Tonex Pedal: #1 Tip for Best Tone - Adjust Input Trim
Vložit
- čas přidán 3. 06. 2023
- This video shows how to adjust the "Trim In" setting on the Tonex Pedal to get the best tone. It's one of the most important settings and affects the tone of all captures and presets. Tonex Pedal at Amazon: amzn.to/3oMxqYo (affiliate link)
My website: masters-of-music.com/ - Hudba
I've had my ToneX a few months now and didn't know about this. Thank you so much man!!
Great video Bro. This seems to be the most important part of the entire pedal
Great video thank you! I was starting to think there weren't any clean amp models on this thing until I captured my own and even that was distorted. At that point, I knew something was up and found your video.
I just got this pedal yesterday and was confused by the clean tones being distorted., awesome. Thanks a ton
Gain staging is so critical to good tone. Thanks for this.
Awesome! I just got my pedal and I’m setting it up, so glad I saw this before using it. Thanks!
thanks for making a great video that's to the point and describes the content of the video in the title!
Thanks for sharing. My ToneX was on 8.5 and with my humbuckers sounds nicer at 0. I think IK M fixed this after the 1.0.5 firmware upgrade so everyone who purchased a unit before April '23 should check this setting
Thank you. This answered my issue 👍
Don't know about anyone else, but I immediately subscribed. 🙂
Great vid and needed.
Great Tip, thank you 🤟
You could set your global input trim to 0.00 leave your volume knob at 10 and just adjust the gain knob on the amp no matter what guitar your using. .You can then save the gain adjustment per preset . Global settings shouldn't be messed with once set properly.imo
Very helpful.
I did notice something last night re the trim and levels. It seems the trim, preset volume, gain and master volume all work off of each other when adjusting input gain. I say this because, after getting my trim set, i adjusted the master and patch volumes and started clipping again. This confuses me a bit because that master volume is supposed to control the overall pedal output. If thats the case, then the clip meter really addresses the whole pedal and not just the guitar input.
Overall fantastic tone and feel. Changing guitars is tricky though. IK should make input trim based on preset and not global.
Thanks for this. I was struggling last night with a clean telecaster.
You're the man
That you for making this vid. I've been wondering why my "clean" tones sound more like "edge of breakup" tones. It would only give me a clean sound if I played gently or turned the volume down.
I just got one of these, and the first guitar I plugged in was a 7 string loaded with Seymour Duncan Mick Thompson Blackouts and I was wondering why it was sounding a bit crap. +8 and those pickups just doesn't work for anything. Thank you for the video!
Hey man cool video. Does this thing actually have smoother less fizzy distortions"? Great playing too! Cheers
Thanks so much. This stuff is not intuitive to a lot of us, and IK assume we all have a background in production.
I use Tonex plugin version, and I have hot pickups, and I set the input gain as +15, that way it sounds the best for some reason, it sounds like real amp, and with more sustain, what do I do wrong?
Thanks! Excellent Demo.
Thanks for the advice
🎸🤘🎸🤘🎸🤘🎸
Thanks for the tip. Just got mine a few days ago and hadn't checked the trim setting. Just watched your video and out of the box it was set to 0.0db as default. Just wondering if they've changed it with some firmware update or something? Cool tip on the Dual for wet/dry recording of the same guitar track as well 👍
I thought I remembered it being set to 0.0db initially too, but the manual says the default is +8 so I don't know. Maybe they changed it on newer units.
@@masters-of-music7602got mine a couple of days ago, and it was set to 8.5 (firmware version 1.0.9, from memory).
If the unit can pickup the signal as LOW, OK and HIGH, I wonder it there could be an AUTO function in the future, keeping everything clean.
How are you doing? All good? :) I bought Tonex One and I'm not able to configure the pedal's global equalization to make a "Low Cut - High Cut" in the Frequency Range. To limit the speaker frequencies.. Could you help me? thanks 🤠
Thanks! So you change the input trim every time you change your guitar?
Can you have different input and output levels for each preset like on the hx stomp?
No that’s the global input trim
Where can I find that capture? It sounds amazing!
Thanks. It's a capture of my single rectifier. Maybe I'll figure out how to upload it at some point but I don't really want anything to do with ToneNet.
Does that mean I have to change a global setting every time I go between a Strat (single coils) and a Charver (Duncan JB) for example?
Not really. The tonex is acting exactly how a real amp would react to pickups with different outputs so just set it and forget it. If you want to I would just make different presets with different levels of gain to match the different guitars (preset gain not the global input trim)
I'm confused.... I have a Stratocaster, and even with the trim at max i still got LOW so I added a pedal (fulltone ocd with drive and volume FULL ON: so loud!) and still get LOW. Is my unit faulty or do I misumderstand?
My trim is set to +14 with very weak strat single coils. With a hard strum i get ”OK” in the display.
Unless I'm misunderstanding, this is only a global setting, correct? To that end, how can you set up the pedal to accommodate different guitars/pickups? It would be great to be able to do this per preset, so that you can have guitar/pickup specific presets when using live.
You have to adjust the setting manually for different guitars; it's not set and forget like Fractal modelers.
@@masters-of-music7602 To be clear, if I switch guitars during a live gig, I’d have to reach down and adjust the trim level to match that guitar? And then do it again when switching back? That seems highly impractical for live use.
@@markwest5217How do you currently adjust when switching guitars? By doing exactly the same thing?
@@christianvanhorn8446 no. I twist, a knob or two, lol
Hey! I use a product called The Fixer from Brown Amplification. Super useful and it makes switching from my Jazzmaster to an ESP with active humbuckers an easy thing to switch.
It funny how IKM did not address this trim adjustment very well in the User Manual ... or how to get to it: You did. Push in and hold the Model Knob? Push it in and release? Do you turn the knob when it's pushed in or when it's released? Important information for sure ... if you don't do it EXACTLY right, you don't get where you need to go. This applies to all uses of the Multi-function knobs in the manual and in their "instructional" videos. Don't leave this to the engineers. Please.
Input trim is the real secret of the tone x pedal...out of the box it sounded very bad...all my fav presets of the free software sounds very low and different at first. Then i began working on the input trim and i made a rule myself to match the sound of the same preset as it sounds on the software... now i am enjoying all the sounds at their best....
Most of the captures sound weak in the software version. By raising the input trim, the amps spring to life.
Mine came set to zero.
Input trim should be a per preset option.
mine always says low when using my gibson les paul. 😂
Funny it’s easier to get to on the TomeX one
Imma need those Chinese companies to copy this asap
TRUTH