Yes, it is, above all, very durable. Especially with my modifications. And I think he is the best all-rounder. In any case, you can't go wrong with the 75 Pro. When it came out I wasn't convinced. But now I'm very happy.
This time it is the tiny whoop pinch cam. You mean the zenchansi cam? Its a great cam! The picture is the best ever analog picture (with good light conditions). Unfortunately it is only 25 fps. And you can see it sometimes in certain light conditions. But it is still a very good cam! czcams.com/video/0gtVZ4s5iB0/video.html
How do we check tinywhoop cam temp ? What is the ranges ? I was also trying new X12 FC and get Core tempt as higher than 70⁰C and more at only 25mW in 2S, would you explain and show OSD of core on 2S tinywhoop aio 5in1 i get scarry day time get line 98⁰C...
Camera temperature? It is not critical. The camera should never overheat. The core temperature of the flight controller can be more than 70 degrees Celsius. That's not a problem. It's only at 80 degrees that there's a higher chance that there's an error. Basically, the heat doesn't do anything to the board as long as it stays below, say, 100 degrees. Theoretically, the boards can withstand 200 degrees (they were soldered at well over 200 degrees in a soldering oven). The only problem is that it would make the board more inefficient and in many cases it would indicate a problem such as bad connector contacts, too tight pid tuning, wrong filter settings, wrong esc settings. Too high vtx power. Poor insulation between vtx and board. It could be due to a lot of things.
@@butterflyfpv there is a big block heatsink on cam that quite hot with only 1S, but it work well on 2S. It's only so hot after time. 1. Thats makes me confuse since none review ever about it, and showing operating temp of an micro fpv cam. Im also in a tropical weather, which temp is crusial during daytime, 2. And questioning this FC X12 Core reaching over 60⁰ and beyond 70⁰ under 2S Li-HV which is recomended in this X12 , i need someone to explain and show X12 FC for 2S in youtube channel ?
Super impressive speed and control!
The result of almost daily practice over three years..🚁 whoop whoop🥳
Nice
Your flying is impeccable! Yes, I definitely agree with you the75 pro is the best! Best bang for the buck!
Yes, it is, above all, very durable. Especially with my modifications. And I think he is the best all-rounder. In any case, you can't go wrong with the 75 Pro. When it came out I wasn't convinced. But now I'm very happy.
Such a nice track :) Good
Great speed you level up tis time!! What cam you use ? What do you think about the fake aliexpress 'PINCH' . Thanks my Whoop friend👌🏼🙌🏼
This time it is the tiny whoop pinch cam. You mean the zenchansi cam? Its a great cam! The picture is the best ever analog picture (with good light conditions). Unfortunately it is only 25 fps. And you can see it sometimes in certain light conditions. But it is still a very good cam! czcams.com/video/0gtVZ4s5iB0/video.html
Looking great as always
Right on buddy. The black frames are the strongest also ;)
is ur pilot name R:1:25 xD, some damn good reception
😂👍🤜🤛
Thoughts on the new air75?
Yes: I made a video about it (and video description with infos). czcams.com/video/o1GGBDw7bAY/video.html
How do we check tinywhoop cam temp ? What is the ranges ?
I was also trying new X12 FC and get Core tempt as higher than 70⁰C and more at only 25mW in 2S, would you explain and show OSD of core on 2S tinywhoop aio 5in1 i get scarry day time get line 98⁰C...
Camera temperature? It is not critical. The camera should never overheat. The core temperature of the flight controller can be more than 70 degrees Celsius. That's not a problem. It's only at 80 degrees that there's a higher chance that there's an error. Basically, the heat doesn't do anything to the board as long as it stays below, say, 100 degrees. Theoretically, the boards can withstand 200 degrees (they were soldered at well over 200 degrees in a soldering oven). The only problem is that it would make the board more inefficient and in many cases it would indicate a problem such as bad connector contacts, too tight pid tuning, wrong filter settings, wrong esc settings. Too high vtx power. Poor insulation between vtx and board. It could be due to a lot of things.
@@butterflyfpv there is a big block heatsink on cam that quite hot with only 1S, but it work well on 2S. It's only so hot after time.
1. Thats makes me confuse since none review ever about it, and showing operating temp of an micro fpv cam.
Im also in a tropical weather, which temp is crusial during daytime,
2. And questioning this FC X12 Core reaching over 60⁰ and beyond 70⁰ under 2S Li-HV which is recomended in this X12 , i need someone to explain and show X12 FC for 2S in youtube channel ?
You Had Me At '75Pro'....... Great Send My Man..