Bro you teach me alot and it's clear you know your stuff but one thing i never ever see u solder and use soldering flux, your solder joints are a mess it's very important to use rosin flux it makes your soldering joints stronger.
Hola profesor,me interesa sus enseñansa,pero no hablo ingles,habría alguna forma de poder traducir sus videos,le saluda Gustavo desde colonia Thompson Paraguay.
Purtroppo la vecchia scuola insegna che mettere duo o tre diodi in parallelo non compensa la somma dell amperaggio totale ci sarà sempre un diodo che conduce di più e facilmente andrà in corto circuito conviene metterne uno con amperaggio adeguato ed un piccolo radiatore termico se necessario....per quanto riguarda il recupero dei diodi non sempre è conveniente.. ..conviene mettere dei componenti nuovi visto il costo molto basso qualche centesimo .. Un saluto a tutti da Milano Italy.
Mr Tevz, change your stupid solder wire to some imported solder wire and also get a needle point soldering iron, you are Effing up customers circuit boards. Please listen to your viewers.
Thank you Mr. Tevz. I always following your video.
Very good again Prof T. Pls continue Master
good
les diodes toujours les diode ou condensateur panne courante bon travail merci
Watching po master
Interesting renovation! Thanks for the information! Peace and good luck to You!
Very good 👍 my teacher.
.high dear tevz.
It was a nice job .
But I wish you would say the part number of the diod!!
sorry.
Nice video sir❤❤❤
Very good my teacher
Nice video sir
Thanks for the content. Greetings from Ukraine.
Good. Nolage. Thanks
continuamos aprendiendo, saludos amigo.
Thank you for the knowledge my teacher
Thanks so much for nice videos sir
sir thank you for your vdeo,
nice video and very good job. thanks very much
Thank you too
Wonderful knowledge Mr Tevz! Thankyou.
Very welcome
Buenas tardes colega excelente trabajo saludos desde Argentina.
Nice new Fluke 289! Good choice! 😊
newbie is watching master
Ok, thanks Mr. Tevz. I like very much. You're 👍😀
Emeğine sağlık ustam. Türkçe altyazılı yayınlamaz oldun. Sağlık ve huzur dolu günler dilerim.
Bro you teach me alot and it's clear you know your stuff but one thing i never ever see u solder and use soldering flux, your solder joints are a mess it's very important to use rosin flux it makes your soldering joints stronger.
I bought a low-quality soldering lead online. a good soldering lead dont need a flux or rosin.
@@tevzTVTevatronicsFlax causes cancer in the long term. It should only be used when necessary
❤❤❤❤❤
Sir please make a video str w6053 in use crt tv supply modification sir please make a video I am waiting
I will
I have a video watch this czcams.com/video/bua5NvWYXBw/video.html
Nice multimeter 🙂
Thanks 👍
Thanks sir.
شكرا
Watching by KDL
Tanks
Thanks ..
👍👍
Hola profesor,me interesa sus enseñansa,pero no hablo ingles,habría alguna forma de poder traducir sus videos,le saluda Gustavo desde colonia Thompson Paraguay.
Turn on subtitle then sellect your language.
Hello . Why did you install the fluctuating voltage but the power board?
New multimeter?
It's not new, My friend sold me at a low price.
Hi engineer
Why did the voltage fluctuate after the repair and before installing the board, and why did you install the board despite the fluctuation
As I said some PWM power supply fluctuates when there is no load or not connected to the main board.
Hello. In such power sources, is it possible to put a consumer on all voltages and test it, except for the main board
a resistor will do, 100 ohms
@@tevzTVTevatronics Hello. Will this 100 Ohm resistor work for any of the voltages (3.3, 5, 12,...)?
Hello
I need software to this board
5844-A7M41G-OP00
Not available.
Purtroppo la vecchia scuola insegna che mettere duo o tre diodi in parallelo non compensa la somma dell amperaggio totale ci sarà sempre un diodo che conduce di più e facilmente andrà in corto circuito conviene metterne uno con amperaggio adeguato ed un piccolo radiatore termico se necessario....per quanto riguarda il recupero dei diodi non sempre è conveniente.. ..conviene mettere dei componenti nuovi visto il costo molto basso qualche centesimo ..
Un saluto a tutti da Milano Italy.
Bro Not Turkish language subtitle
It has, try selecting it on the setting.
@@tevzTVTevatronics not setting Turkish language
You could have removed the bad diode
Pin 8 is vcc 3.3v not pin no 5
Mr Tevz, change your stupid solder wire to some imported solder wire and also get a needle point soldering iron, you are Effing up customers circuit boards.
Please listen to your viewers.
good
Nice video sir
Thanks