Err 35 occurred before the run contactor pick-up 1 .check whether the 1st down forced deceleration is valid 2 .F4-01=1 3 .whether the inspection switch on the inspection state and able to done the inspection run 4 .F0-00=1 Err 35 occurred as soon as the run contactor pick-up 1 .check whether the inspection switch on the inspection state Err 35 occurred during running 1 .check whether running overtime, , run over the time of Err 35 occurred when meet the 1st levelling position 1 .Whether the F4-03 INCREASE WHEN UP, DECREASE WHEN DOEN, switch the main board PGA and PGB if it is not . 2 .Level sensor N .O, N .C .setting error . 3 .level sensor signal flash, check the plate Err 35 during running: 1 .check whether run overtime of F9-02 setting value, and no receiving of levelling signal 2 .the floor distance less than 50cm, check the sensor 3 .the F6-00 setting too small Run to the top floor: 1 .the 1st forced slowdown is valid and juadge on the door-area, check whether the learned floor amount are same as the setting of F6-00 and F6-01 . 2 .Error occurs if the lifting height less than 50cm Err35 occures when power-on Check whether the plate length is 0 after power-on
Group F0: Basic parameters F0-00 Control mode 0: Sensorless vector control (SVC) 1: Closed-loop vector control (CLVC) 2: Voltage/Frequency (V/F) control 1 - ★ 192 F0-01 Command source selection 0: Operation panel control 1: Distance control 1 - ★ 192 F0-02 Running speed under operation panel control 0.050 to F0-04 0.050 m/s ☆ 193 F0-03 Maximum running speed 0.250 to F0-04 1.600 m/s ★ 193 F0-04 Rated elevator speed 0.250-4.000 1.600 m/s ★ 193 F0-05 Rated elevator load 300-9999 1000 kg ★ 194 F0-06 Maximum frequency 20.00-99.00 50.00 Hz ★ 194 F0-07 Carrier frequency 0.5-16.0 6.0 kHz ★ 194 Group F1: Motor parameters F1-00 Encoder type 0: SIN/COS encoder 1: UVW encoder 2: ABZ incremental encoder 3: ECN413/1313 absolute encoder 0 - ★ 195 F1-01 Rated motor power 0.7-75.0 Model dependent kW ★ 195 F1-02 Rated motor voltage 0-600 Model dependent V ★ 195 F1-03 Rated motor current 0.00-655.00 Model dependent A ★ 195 F1-04 Rated motor frequency 0.00-99.00 Model dependent Hz ★ 195 F1-05 Rated motor speed 0-3000 Model dependent RPM ★ 195 F1-06 Encoder initial angle (synchronous motor) 0.0-359.9 0 Degree (°) ★ 196 F1-07 Encoder angle at power-off (synchronous motor) 0.0-359.9 0 Degree (°) ★ 196 F1-08 Synchronous motor wiring mode 0-15
Err 35 occurred before the run contactor pick-up 1 .check whether the 1st down forced deceleration is valid 2 .F4-01=1 3 .whether the inspection switch on the inspection state and able to done the inspection run 4 .F0-00=1 Err 35 occurred as soon as the run contactor pick-up 1 .check whether the inspection switch on the inspection state Err 35 occurred during running 1 .check whether running overtime, , run over the time of Err 35 occurred when meet the 1st levelling position 1 .Whether the F4-03 INCREASE WHEN UP, DECREASE WHEN DOEN, switch the main board PGA and PGB if it is not . 2 .Level sensor N .O, N .C .setting error . 3 .level sensor signal flash, check the plate Err 35 during running: 1 .check whether run overtime of F9-02 setting value, and no receiving of levelling signal 2 .the floor distance less than 50cm, check the sensor 3 .the F6-00 setting too small Run to the top floor: 1 .the 1st forced slowdown is valid and juadge on the door-area, check whether the learned floor amount are same as the setting of F6-00 and F6-01 . 2 .Error occurs if the lifting height less than 50cm Err35 occures when power-on Check whether the plate length is 0 after power-on
Good vedio 💓💓
السلام عليكم بجي عطل 35 ازاي ترتيب مفناطيسات البير ؟
Err 35 occurred before the
run contactor pick-up
1 .check whether the 1st
down forced deceleration
is valid
2 .F4-01=1
3 .whether the inspection switch on the inspection state and able to done the inspection run 4 .F0-00=1
Err 35 occurred as soon as the run contactor pick-up
1 .check whether the inspection switch on the inspection state Err 35 occurred during running
1 .check whether running overtime, , run over the time of Err 35 occurred when meet the 1st levelling
position 1 .Whether the F4-03
INCREASE WHEN UP, DECREASE WHEN
DOEN, switch the main board PGA and PGB if it is not . 2 .Level sensor N .O, N .C .setting error . 3 .level sensor signal flash, check the plate Err 35 during running: 1 .check whether run overtime of F9-02 setting value, and no receiving of
levelling signal
2 .the floor distance less than 50cm, check the sensor 3 .the F6-00 setting too small
Run to the top floor: 1 .the 1st
forced slowdown is valid and juadge on the door-area, check whether the learned floor amount are same as the setting of
F6-00 and F6-01 . 2 .Error occurs if the lifting
height less than 50cm Err35 occures when power-on
Check whether the plate
length is 0 after power-on
Please talk and explain. Sir
what's you need to know telling me
I want to know how to start inspection run and control wring.? Please explain step by step.sir.
Gearless and geared.
Group F0: Basic parameters
F0-00 Control mode
0: Sensorless vector control
(SVC)
1: Closed-loop vector control
(CLVC)
2: Voltage/Frequency (V/F) control
1 - ★ 192
F0-01 Command source
selection
0: Operation panel control
1: Distance control
1 - ★ 192
F0-02
Running speed under
operation panel
control
0.050 to F0-04 0.050 m/s ☆ 193
F0-03 Maximum running
speed 0.250 to F0-04 1.600 m/s ★ 193
F0-04 Rated elevator speed 0.250-4.000 1.600 m/s ★ 193
F0-05 Rated elevator load 300-9999 1000 kg ★ 194
F0-06 Maximum frequency 20.00-99.00 50.00 Hz ★ 194
F0-07 Carrier frequency 0.5-16.0 6.0 kHz ★ 194
Group F1: Motor parameters
F1-00 Encoder type
0: SIN/COS encoder
1: UVW encoder
2: ABZ incremental encoder
3: ECN413/1313 absolute
encoder
0 - ★ 195
F1-01 Rated motor power 0.7-75.0 Model
dependent kW ★ 195
F1-02 Rated motor voltage 0-600 Model
dependent V ★ 195
F1-03 Rated motor current 0.00-655.00 Model
dependent A ★ 195
F1-04 Rated motor
frequency 0.00-99.00 Model
dependent Hz ★ 195
F1-05 Rated motor speed 0-3000 Model
dependent RPM ★ 195
F1-06 Encoder initial angle
(synchronous motor) 0.0-359.9 0 Degree
(°) ★ 196
F1-07
Encoder angle
at power-off
(synchronous motor)
0.0-359.9 0 Degree
(°) ★ 196
F1-08 Synchronous motor
wiring mode 0-15
Saalam aliykum sir, thanks. Plz make video all errors solution with your voice.
Help nice 3000 error 40 what to do?
sub code?
How to remove Error 35 during shaft learning please tell me?
Err 35 occurred before the
run contactor pick-up
1 .check whether the 1st
down forced deceleration
is valid
2 .F4-01=1
3 .whether the inspection switch on the inspection state and able to done the inspection run 4 .F0-00=1
Err 35 occurred as soon as the run contactor pick-up
1 .check whether the inspection switch on the inspection state Err 35 occurred during running
1 .check whether running overtime, , run over the time of Err 35 occurred when meet the 1st levelling
position 1 .Whether the F4-03
INCREASE WHEN UP, DECREASE WHEN
DOEN, switch the main board PGA and PGB if it is not . 2 .Level sensor N .O, N .C .setting error . 3 .level sensor signal flash, check the plate Err 35 during running: 1 .check whether run overtime of F9-02 setting value, and no receiving of
levelling signal
2 .the floor distance less than 50cm, check the sensor 3 .the F6-00 setting too small
Run to the top floor: 1 .the 1st
forced slowdown is valid and juadge on the door-area, check whether the learned floor amount are same as the setting of
F6-00 and F6-01 . 2 .Error occurs if the lifting
height less than 50cm Err35 occures when power-on
Check whether the plate
length is 0 after power-on