Installing An HEI Distributor, Easy Upgrade For Your Ford Small Block!
Vložit
- čas přidán 6. 09. 2024
- I was surprised how cheap it was to buy an HEI for this Ford 302. Came with the coil and control module so all you have to do is give it 12V. Here is the one I bought - amzn.to/3BvhWce (affiliate) and the wires - amzn.to/2YBBLjO (affiliate)
Check out struggleville.net for the latest AMAZING deals on tools, automotive, home improvement and tech items!
This is my 2nd channel, be sure to subscribe to the main - / thestruggleville
E-mail - PJ@struggleville.net
Shipping address:
PJ
2205 S. Perryville Rd. No. 138
Rockford, IL 61108
As an Amazon Associate I earn from qualifying purchases.
I havd fitted many of these dizzys. They work amazingly well.
12volts WITH A RELAY AND THICK WIRES TO GIVE PROPER VOLTS AND AMPS REQUIRED FOR PEAK EFFICIENCY.
MAKE SURE THE DIZZY HOLE IS VERY CLEAN FOR A GOOD EARTH!!
Hope this helps.
Make sure HEI is connected to =12v and not though a ballast resistor or ballast wire.
What people say you cannot wire the distributor hot and choke hot together.... it's 12v switched!
I like how you say "It works just fine for me".
That's the difference between people who just repeat what others say and people that do things. You will know if it works or not when you do it.
I put one of those on a Cleveland back in the 90s it was called a DUI Davis unified ignition it was a 10000 RPM distributor Plus I loved onewire install I paid 500
Great video. The part about it needing to sit flush on the oil pump shaft saved me. Thank you
What kind carb do you have and where did you hook the vaccum to
Hey! So, I have a '74 K20. I got it running, but it didn't have much power when I stepped on the gas. I thought I needed to adjust the timing and tweak the carburetor. I started with the HEI distributor, set it to top dead center, dropped the distributor in, and put the spark plug wires in the right order. But it's still not running right, even though I know there's spark and it's getting gas. It cranks but won't fire, and now the carb is spitting gas out the top.
Its not running right or not running at all? I dont know what issue you had to begin with but I would guess you have the distributor 180 degrees out right now. Take the cap off and see where the rotor is aiming then pull the distributor and rotate it 180 degrees.
Make sure you have firing order correct. If it's a 5.0 ford none ho it's a different firing order than a 5.0 H.O or 351
Points and condenser's aren't really difficult to do, the issue for most people though is, the distributor has a bad reputation with moisture already, the points and condenser's only add to the misery, plus they need to be adjusted often. It's dead tech (if you can even call it that) and no one wants the hassle lol going electronic is cheap and soo much better.
Stop putting apostrophes in condensers!
Where was the number 1 plug on the HEI I can't find it any where
2:19 Used a 90 degree fitting and my HEI clears it, on the 351 & 5.0
how many volts are going to the coil? there is a resister in the stock wire, its not getting the full 12volts
Could you tell me the circumference of the cap? Not sure if I have enough room for that distributor.
I dont blame you for going to electronic ignition but points are very easy and simple to adjust and work with. Dwell is an easy adjustment with a cheap dwell meter. Could you put a 90 degree fitting on the intake manifold for the heater hose would that stop it from hitting the cap? Looks like you have a lot of restoration work to do on the mustang.
Yeah at some point that is probably what I will do with the heater hose. The mustang definitely looks rough but has come a long way. My dad and I replaced everything from the firewall forward like 15 years ago. Frame rails, shock towers, torque boxes, radiator and radiator support, springs, shocks, control arms, ball joints, tie rod ends, brakes... everything. Hoping to work on it this winter but that means putting the Caprice or Corvette in the tent and I have to figure out how to keep mice out first. Might try one of those zip up car covers.
I was asking myself the same thing put a 45 or 90 piece !!!
I feel you might have skipped a few steps, like the whole installation side.
It needs 12 volts to the distributor. The hot wire from the original coil is not 12 volts if it has points.
I have a 302 in a 2000 mustang with a single wire distributor where do I wire it properly?
Find your ignition wire and tap it into that wire so when you switch the key to the on position it’ll receive power I just did this on my 08
Where does the coil spark plug wire go to when converting with this exact same distributor? I bought one of these off of Amazon as well as the two wire plug separately and I’m having a difficult time figuring out where to put the ignition coil wire from the factory ignition coil it used to go to the center of the old distributor cap.Thank you in advance for any help
The old distributor had an external coil to you had a short wire going from the coil to the distributor. This new distributor has an internal coil so you no longer need that short wire.
What gear does that HEI cone with? I assume you are running a flat tappet cam?
Hey I done a efi to carb swap on my 1990 f250 302, im installing one of these hei distributors, I have everything down so far but im not sure what to do with the efi wiring harness, like the harness for the lights and all that. Do you know what to do? Cause the hei distributor didn't come with a plug for the harness
Haber hombre yo acabe de finalizar una conversión de un Ford 392 de efi a carburador, tuve que quitar todo el arnés de cables y rehize la electricidad completa del carro, el +vcc, del hei se conecta al swich de encendido del vehículo además de la bomba de gasolina qué en este caso se debe poner una que sea Para carburador osea, la presión debe ser especifica para carburador, y lo otro que se debe conectar al swich es el +vcc de los relojes del panel frontal, pues esos deben prender cuando el carro encienda, en si eso es muy fácil, el dolor de Cabeza es el Tema de luces, eso si es algo complejo , en mi caso tuve que usar diodos de 10 amperios, de rectificacion, para poder separar los canales de direccionales, izquierdo derecho y unir además las luces trasera para las direccionales, los diodos son la clave para separar y al mismo tiempo unir las líneas de luces, el resto es pan comido, a mi lo que más me complicó es el Tema de esas líneas, el resto lo que es conectar el distribuidor hei y la bomba de gasolina es fácil van en una sola línea tienen que encender ambas al accionar la llave del carro y el arranque va en la Linea de arranque de la llave, después va a la bobina de arranque y esta acciona el mismo, en si es sencillo, pero si toma tiempo de trabajo. Al hacer esa conversión lo unico qué se debe quitar son los cables el resto se deja igual, el canister todo debe quedar en el mismo lado, y según como quiera hacer la adaptación, se puede dejar el mismo manifold pero se debe hacer un adaptador para el mismo que conecte al carburador o en su caso se debe cambiar el múltiple de admisión completo, en mi caso hize un adaptador para conectar el carburador a la misma toma donde hiba el cuerpo de aceleración, de esa manera no tengo que desarmar medio motor y queda más Estetico pues eteticamente queda muy similar al sistema fuel inyection, pero con carburador, estoy en eso, es algo experimental, lo he visto en carros más pequeños y si funciona pero jamás lo he visto en un Ford 302 aun así debería funcionar, debido a que se usa la misma admisión del egr para en vez de meter humo por hay se mete combustible + aire, y la valvula egr queda en su misma pocision tal cual, en pocas palabras lo único que se saca es el arnés, la computadora y la mariposa de aceleración. Y en vez de esta se pone el carburador.
Chevy ignition on a ford defiantly an upgrade
Could you swap out the old ford gear to this distributor.don't chevy hei dizzy have that pin for the pump, and ford's the Allen type ? Can you do this on a BB 460 . Just curious.
Where does the vacuum line from the distributor should go?
There's a vacuum port on the carburetor. It will vary between different makes of carbs, though. On a 4 barrel Holley it's located on the front lower left hand side, on the base plate.
get the module out dont test it drop it in the bin get a bosh not a bosh like BOSH and go. my 67 mustang is to hot under the lid so i moved the module to the radiator bulk head , you will need double earthed armoured multi core wire to it
Здравствуйте! Купил такой же только с красной крышкой.Какой зазор у шестерни и перемещение вала вверх- вниз. У меня 5мм. Это много?
We're can I put number 1 on the distributor
Let me know if you find this I’m having the same issue
Should the spark plug gap change?
Gap .035
You didn’t have any issues with the pink resistance wire stopping it from running?
Nope
What headers are those, did they clear your power steering? I have a ‘67 with a 289 with some junk shorties that i wanna swap out for long tubes
you showed no install. distributor on a table then it installed. How did you keep the gear on bottom of shaft? mine just falls off
Put a dab of grease or vaseline on it. Will stay on long enough to get it in place
What distributor would this engine be from?
Would you mind telling me exactly which distributor is the. ????
Nice video an helpful. Wish it was a little more detailed on how you set the timing and found #1 on the cap etc etc
What?
Super easy all you have to do Is set the distributor in with the rotor on and turn engine to TDC on number 1 and where the rotor is pointing Is where the number One is on Cap then mark with marker for the next sorry sap who has to work on it 😀
Is this the summit blueprint distributer?
how do you know what number on the plugs? the caps are not numbers
i know right
I had an issue with my HEI DISTRIBUTOR. I was wondering why wasn't my C10 truck starting . At first it was, no problem starting. Than I decided to install spark plug wires insulation sleeves. I had concerns about the wires to close to the exhaust. Anyway, once I remove the wire from the distributor. And putting everything back on the the same way. It wouldn't start. I said to myself what the heck is going on. I had fuel, New battery, New Starter. The engine would crank. I remove the power to distributor and reclip it back in the HEI BATTERY TACH. It started first turn on the key. I believe once you remove the wires from the distributor, u have to reboot the HEI BATTERY tachometer. I'm I correct? Please advise. Thank you Robert
Absolutely not. You're thinking to hard. 12v goes to BAT, tach wire goes to tach.
Do these HEI’s on a Ford interfere with a standard size air cleaner?
they are bigger than the oem distributor
Should the vacuum only face forward towards the radiator? Mine is facing closer to the passenger tire?
Does not matter
When lining a distributor up, the only thing that matters is that the spark goes to the correct spark plug and at the correct time. I'm more use to a Chevy but the concept is all the same. Hell, you could have rotor facing backwards at TDC when normally it's supposed to be forward, but the main thing that matters is that the plug wires are changed to adjust for that.
Where is your coil? I didnt see it in the video
For the HEI the coil is under the cap. The wires on the side of the cap connect to it
Which wire would I use on an 85 mustang 5.0?
Neither
Should of got a duraspark n hei that
Hey great video, I saw when you turned on the car that the oil pressure gauge worked. On my 67 I have a 351w and I can't get the oil pressure to work right I have replaced the oil pressure sensor, but still nothing. My gauge reads high. I know my gauge works, what oil pressure sensor do you use?
If your gauge runs High that means you got good oil pressure Lol
How far does this distributor rev to?
This one can rev up to 8,000 rpms
Now you need to replace that carburetor with a Holley Sniper EFI
I just need the car to move so I can switch around the cars when working on it.
Nice!
I dont know anything and don't want to learn. Thats the world we live in now, computer says no.
My wife a school teacher and most the kids are going into high school not able to tell time unless it’s digital. Hell, in my area the of the country the best thief deterrent is a manual transmission in your automobile. Gen X don’t know how to drive a stick shift
Did not see anything changed out just explanations
Did you need to see people wipe their ass or did you just need an explanation?
@@Struggleville2 full details please 67 mustang owner with a 1970 302 i know its hard but you know how did you set and seat the rotor for example or how is it wired i am just saying man you left allot of important details out
Worst vid ever,how do you put it in,i tried what you did n it didnt magicaly apear in the engine? Weird
The best thing going for that Ford(Fix or repair daily) is that GM HEI distributor being used to make it run better. Who ever made this conversion distributor happen . I envy .
Actually the Hall Effect Ignition isn't near as good as the Dura spark ignition. it uses the same components as MSD. except for the ignition module. and the Dura spark is a direct wire up to the MSD module. and Dura spark is a true CDI (capacitive discharge ignition). and HEI distributors have an issue with the bushings failing. because of all the weight from the mechanical advance being up high on the distributor shaft. not to mention the fitment issues.
Jesus Christ, man that was the most uneducational thing I've ever seen. You focused on a lot of BS when you could have gotten to the important facts. Like one, it doesn't matter where the MF distributor falls, you can run number one from there. Did you know that!!! Ok number two, it only takes a Electronic Ignition distributor off an old Ford and the PCM off the driver fender and the four wire harness that goes from the PCM to the distributor. Run a hot wire from a fuse to the red wire coming in the PCM, it will be with a while wire. It's done
I agree. Waste of 5 minutes
It's not a PCM it's an ignition module.
you didn't show installing the distributer. useless
Why put a big goofy looking gm distributor in a ford.😂