Helpful videos. just a small input please recommend your visitors, they should use sprue break after plasticizing not before. If they use sprue break first and then start plasticizing, the chances are you will be wasting lots of material as melt will drool through open nozzle while plasticizing. How much will it drool? it depending on how much back pressure you are using, type of material and melt temperature. So inject, plasticizr and then sprue break. Try the other way and you will find out.
Helpful videos. just a small input please recommend your visitors, they should use sprue break after plasticizing not before. If they use sprue break first and then start plasticizing, the chances are you will be wasting lots of material as melt will drool through open nozzle while plasticizing. How much will it drool? it depending on how much back pressure you are using, type of material and melt temperature. So inject, plasticizr and then sprue break. Try the other way and you will find out.
nice
Sir mould opening speed kam and runner bush polish krke bhi is problm ko dur kr skte h
Sir what is barrel temperature and how is control but don't heating temperature
Sir pvc matesial ka runner breaking problm aati h isme bhi suck bake rakh skte h
Very nice bro , keep it up ...
Nd thanks for supporting us ..
👌👌🤘🤘
Sir what is the reason of nozzle leakage
sir make video on part sticking ..without runner type mold(HRC)
Thanks brother ur done good job
Sir step me injection speed or pressure kaise set karte hai please is baare me bataye.
Thank u so much sir
Nice Thakur Sahab
Thnku mere bhai
Sir please total trouble shooting injection molding I want to need
Nice 👍
Mould louding ke time locking kaise lete h sir please visually video banaye 🙏🙏
बहुत बढ़िया भाई।
Shukriya bhai
Thanks sir
👍👍👍👍
इंजेक्शन मोल्डिंग में सुख बाइक किसे कहते हैं
Ejector ko kaise operate karenge
I have this probleam brother.
Thank you bro
Runner mai flash k kya karan hai
Sir agar San kuch ok ho fir BHI runner again to again stik
Thnx Bhai
good sir
Thnxx dear
Nice video
Thnxx dear
Very Nice. It will be better if u load trouble shooting chart at the end of the video.
Sure iwill make blogs for them
Thanks bro
Tq sir
Sir ji mere me same problem aata hai and I have second used machine included inside panel board so how to set sprue break ( and suck back)
Suckback ka ek aur video hai use dekho shayad samjh aa jaye kuch
@@PLASTOTECH mere machine me muje maloom nahi hai kaha se set hoga aapka number do to aapko me video se Bata sakta hu machine if possible sir
Who can check barrel problems
Thankyou bro
Wlcome bro
Mould startup ke time plc me kaha locking and tonage kaise set kRte hai sir plz make a video
Ok bro
Sir incorder ke bare me bataia
Sar Injection moulding machine clamping force / tonnage calculator process video
First troubleshooting start kiya than use finish kardun phrr age inhi sab p banayege don't worry
Ok
boss part sticking cavity said. this one video give bro
PLEASE MAKE IT ENGLISH VERSION TOO BECAUSE I AM FOLLOWING YOU VIDEOS
Hi
Sir cushion ke bare me bta dijiye
I am opreter of the injection molding machine
Cushion p video hai jao dekh lo bhai phrr batana jaise ho
@@PLASTOTECH sir aap bhut Hi achche video bnate sari ki sari problem solve kr dete ho
Thank you so much sir
Always wlcome mera bhai
Bus channel subscribe kal lena aur baki dosto tak share kar dena
Request to descuss in english language
How to recover username and password
English please
Sure we already created a channel named as plastotech english and videos will b out very soon
English please 😭
Don't worry bro i have planned to start another channel as plastotech english it will be just starting as soon as we can so stay tuned u will get all.
@@PLASTOTECH ok thanks u
Thanks bro
Wlcom bro..@keep sharing
@@PLASTOTECH
On all pej hindi send molding menu