The cutting accuracy on these is so impressive. At my place of work, the normal process for cutting our brackets is going through 3 processes starting with a shear, then onto a punch press, and then a splitter to make 2 brackets. The trumpf laser cuts the brackets so precise that it makes a super sharp edge on the brackets that actually shaves off bits of brass on the bracket welders. I'm not in that department anymore, but I've heard they're having to change the process for the final welding of the brackets to prevent having to change the brass in the bracket welders after every production run of a certain size. Our old laser cuts at about 300 in/min. Our new trumpf laser cuts at 960 in/min! Impressive piece of engineering! I put in for the job to run it, but unfortunately didn't get it.
@@rnicko86 as long as the machine gets regularly serviced I work a c02 trumpf 3030 manufactured in 2006 still going strong I used to work the old 3030 Bosch control one that was still going after 20 years the worst thing to happen is getting water into the resonator.
always test cut with this machine....the number of parameter changes I had to make was ridiculous ...check the head and make sure its clean...dial back the speed test it
Hi Vijay, This is Kevin from ruijie laser. Are you interested in fiber laser cutting machine? pls feel free to contact me. Whatsapp/Wechat: 0086 15662784401.
I don't have much experience with newer lasers, but with an older laser after much fine-tuning my parts still needed a bit of deburr work. I think it's the reflective nature of aluminum that makes it especially difficult to cut without dross/burr. Keep fine-tuning, and good luck to you. Anything over .063 aluminum having a burr is normal. .090 or .125 thick it is well known you will have a burr, very little you can do about it.
The cutting accuracy on these is so impressive. At my place of work, the normal process for cutting our brackets is going through 3 processes starting with a shear, then onto a punch press, and then a splitter to make 2 brackets. The trumpf laser cuts the brackets so precise that it makes a super sharp edge on the brackets that actually shaves off bits of brass on the bracket welders. I'm not in that department anymore, but I've heard they're having to change the process for the final welding of the brackets to prevent having to change the brass in the bracket welders after every production run of a certain size. Our old laser cuts at about 300 in/min. Our new trumpf laser cuts at 960 in/min! Impressive piece of engineering! I put in for the job to run it, but unfortunately didn't get it.
I like the music :)
I ran a 3030 for 12 years and you check the center the beam at the start of every shift.and there great for doing government jobs
I assume you mean tapeshot you check it more than once
Hello sir.. For 12 years the laser beam still stable or any degradation capacity normal?? Please answer..
@@rnicko86 as long as the machine gets regularly serviced I work a c02 trumpf 3030 manufactured in 2006 still going strong I used to work the old 3030 Bosch control one that was still going after 20 years the worst thing to happen is getting water into the resonator.
@@jamesirvine2579 what happen the resonator on a long periode of time?
máy thích quá. Mơ ước của tôi
Very good
I like it
song?
You have to change and modify parameters
Does this laser have the welding option?
no
No
I'm oparating one of this
always test cut with this machine....the number of parameter changes I had to make was ridiculous ...check the head and make sure its clean...dial back the speed test it
В 2014-м году моя нокия 3310 снимала более качественно. Вот вам и супертехнологии
А они камеру рекламировали, да? Я не сразу понял
trabalhei com corte a laser
me gustaria conseguir un manual de laser trumpf 5000
olá
me passe seu email
inakiimb@gmail.com
Yo también :) pero in inglés por favor 🙏
abubakeraltamih@yahoo.com
Muchas gracias
HAVE ANY JOB OF CNC TRU LASER OPERATOR
how are you
Good
Do you know me?
How much price?
Hi Vijay, This is Kevin from ruijie laser. Are you interested in fiber laser cutting machine? pls feel free to contact me. Whatsapp/Wechat: 0086 15662784401.
Das Video wurde doch in der Bearbeitung beschleunigt! Um die eigentliche Schneidgeschwindigkeit zu verfälschen.
Hab das Ding schon live in meiner alten Firma gesehen, ich kann dir sagen: Nein. Das Ding ist so scheiß-schnell.
aluminum seems to have bur all along the edges every part I cut. I don't know what the proper settings are. trumpfs settings don't work
Please contact service. It could be a few reasons. Maybe something as simple as bad pressure settings or 3rd party nozzles.
Ridge means the focus settings must be adjusted.
it is also the nature of the material. aluminum will always leave a ridge more aggressive than any other material.
It will always have a bur on it unless it is very thin aluminium. Try cutting 15mm aluminium the bur is ridiculous
I don't have much experience with newer lasers, but with an older laser after much fine-tuning my parts still needed a bit of deburr work. I think it's the reflective nature of aluminum that makes it especially difficult to cut without dross/burr. Keep fine-tuning, and good luck to you. Anything over .063 aluminum having a burr is normal. .090 or .125 thick it is well known you will have a burr, very little you can do about it.
fiber laser
If their software wouldn't be such a mess it would be awsome. But the interface system is so bad, I only can say it's broken by design
Potato video quality
salvagnini is better!!
240p quality video? really?