How to replace Toyota AYGO Front Brake Pads
Vložit
- čas přidán 6. 09. 2024
- How to replace Toyota AYGO Front Brake Pads
From start to finish.
Link to all tools used, www.amazon.co....
Link to buy Big Grips, amzn.to/389NbM1
Link to new brake pads, £17 amzn.to/31WzsVO
Link to new pads and discs, £40, amzn.to/2Hl9IJx
Link to Pad Lube paste £10 amzn.to/3ijKPzL
![How to change front brake pads / front brake pad set on TOYOTA AYGO 1 (AB10) [TUTORIAL AUTODOC]](http://i.ytimg.com/vi/D-ZMwJW6b8A/mqdefault.jpg)
You have been a great help doing jobs on my aygo with leaks getting lights out I am a bricklayer and get ripped off with garages thanks
Glad to help, Thanks for the great comments👍🏻👍🏻🛠
Thanks for the videos, I’ve been using them to do bits on our work car and alls been good so far plus I’ve enjoyed doing it with my lad. Going to do the break pads this weekend and get the wife to take it out first time to check them.
Thanks again.
😂 Alway best to let the wife do the test run, Thanks for the great comments👍🏻👍🏻🛠
I've always wanted to change brake disks on my car, but have been too worried about ballsing it up! You make it look so straight forward I'm going to give it a go. Thank you.
Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 I still haven't done it yet! I read my Haynes manual and it mentioned clamping the brake line when winding back the caliper, to avoid the possibility of flipping the rubber seals on the master brake cylinder! Do you ever clamp? I'm assuming you've never had any problems with flipping the master cylinder. Thanks again.
Proper helpful video, cheers mate.
I've never really worked on cars before but got to start somewhere! Saves me a few quid on labour
Glad I could help, Thanks for the great comments👍🏻👍🏻🛠
Thank you very much for your proven quality guidance in reducing my Aygo tyre pressures ......I had weekly, religiously kept all four tyres previously inflated to 32psi, I've dropped all four to 25psi & instantly noted a far comfier all round ride x...your advice is priceless xxx
Thanks Charlene, you got me thinking the other day, I was thinking about doing a live questions answers thing, maybe seeing if viewers would send me videos of problems by email or uploading to CZcams, I could maybe give advice, what do you think would you watch it" be honest" or is it a duff idea 👍🏻👍🏻🛠
@@aaanton11 I think that's a great idea!
i would replace those disks on my car at the same time tbh, great vids mate
Thanks for the great comments 👍🏻👍🏻🛠
@@aaanton11 Hi, will i have to do a engine light reset after changing the oil on these mines a 2014 model? Thanks.
@@gtibruce - No. Your car's ECU is not aware when you change the oil. Nothing to reset or do in that regard.
brilliant honest mechanic, how refreshing...wish you lived next door....great video.
Glad you enjoyed it, Thanks for the great comments👍🏻👍🏻🛠
This is amazing man, thank you so much, very clear explanation, very neat and tidy, perfect !
Glad it helped! Thanks for the great comments👍🏻👍🏻🛠
Awesome video thank you, bought the pads & will change my own now rather than pay the garage
Thanks for the great comments 👍🏻👍🏻
Hi mate great video just by watching this I've decided I can replace brake pads meself instead of paying someone else thanks.
You can do it, Thanks for the great comments👍🏻👍🏻🛠
Many thanks, rather than brake dust the deposits around the front wheel were looking like rust ! Down to the metal needless to say, all the best
Glad it helped, Thanks for the great comments👍🏻👍🏻🛠
I'm grateful, successfully changed them today
well done, Thanks for the great comments👍🏻👍🏻🛠
Excellent video, just found the one for changing the brake shoes.
Thanks for the great comments👍🏻👍🏻🛠
So simple, Toyota wanted a fortune for 20 minutes work.
Thats why these cars are fantastic, well done Thanks for the great comments👍🏻👍🏻🛠
1.34 used a chisel to grind down the edges & circumference of my discs on my 2002 Yaris,although not as bad as the Aygo thou.4.53 was like my pads lol Got mine fro £26 Brembo pads from Euro car parts in a sale.You should show the viewers you should remove the cap from the brake resevoir at the start thou....good video all in all.
Thanks for the great information👍🏻👍🏻🛠
A tiny bit more than 35 years messing with nuts and bolts and a formal mechanical education to go along.
Unless I'm doing some brake oil/pipes/hoses intervention the cap NEVER comes off. Never spill, never any issues...
Why in the world people continue feeding ridiculous myths beats me! :-O
Thanks for taking the time to put this up - expertly done. Got to do the same on my IQ so looking for tips - subscribed. Take care
Thanks for the sub! and Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 I recently replaced the brake pads. My garage is now saying they want to put in new brake discs as well, but that they also have to put in new brake pads because the ones I put in are now grooved to the old ones. I've only driven 30 kilometers with the brake pads I put in, so I feel like the brake pads can still be used on new discs. Are they right?
Ordered a set of replacement slide pins, one every so slightly different what one goes on top & bottom respectively x
I thought they were the same,😂 check the newer video this has some close ups of the sliders, czcams.com/video/OBXpOLzVrI0/video.html Thanks Charlene for the great comments👍🏻👍🏻🛠
nice helpful video, especially the bit about the brake fluid, didn't know that. Thanks for helping us out.
Thanks for the great comments👍🏻👍🏻🛠
This is why I love youtube....
Great tutorial video, you broke it down so that the intructions were idiot proof.
I had an idea how to do it but this video saves me haveing to work it out.
Camera angles were perfect, I got to see everything I needed. You should consider
a job as camera man in the porn industry!!!
Thanks Ma man !
Thanks for your comments 😂😂CZcams is great 👍🏻
Didn't see you using an axel stand just a jack to support the vehicle?
Why didn't you usesome brake cleaner spray to clean away the dust and dirt first, didn't see you using any brake pad lubricant either on the reassembly?
Any torque setting's for the brake caliper or wheel bolts?
But otherwise a good video
Great helpful video, Just about to do mine this week. Thanks for the tips.
Thanks Garry for the great comments👍🏻👍🏻🛠
Excellent job mate! Well done. Helped me a lot!
Thanks for the great comments 👍🏻👍🏻🛠
Have you got a video on how to bleed the brakes and replace brake fluid? please make one, thanks
Got one coming soon, Thanks for the great comments👍🏻👍🏻🛠
Thanks mate saved me a garage rip off.
Glad I could help Thanks for the great comments👍🏻👍🏻🛠
Those discs should not have been reused, left side heavily lipped and both completely corroded.
I like to get my wear out of components, they will be replaced next service, as the pads are getting low again, Thanks for the great comments👍🏻👍🏻🛠
Just had my MOT and been told the front discs and pads will need changing soon.
So looking how to do it.
Now, all the pads I've replaced on previous cars have had a spring that pushes the pads away from the disks.
Where are the springs on these pads and if they have no springs what stops them rubbing on the discs constantly?
TIA.
There are no springs, they will only rub when pressed by the piston, Thanks for the great comments👍🏻👍🏻🛠
Gi I have a problem/question about my aygo 2012 reg .
When you press the brake say 65mph down to 50mph there is a vibration in the footwell (I was not driving my son was ) but I felt the floor vibrate he said NO vibrations in the peddle or steering wheel .
Iv checked the disks not worped an no score marks
Pads almost new .
Nothing lose or broken that I can see .
There is no vibrations driving up or down the gears it only happnds slowing down from 60mph above
If your doing 50mph an slow down to 40mph nothing..
Only from above 55mph down
Brand new tyres (less than 3 months old all 4) .
What do you think it might be an how to fix it . Thanks
I would have said warped brake disc, you will only see with a DTI Gauge, but there is also a chance one of the front wheels might be out of shape on the inner edge (pot hole damage) that causes the same issue, Thanks for the great comments👍🏻👍🏻🛠
Nice video, what is the liquid your put on the brakes before placing them, Thanks
amzn.to/3ijKPzL here is the link Thanks for the great comments👍🏻👍🏻🛠
Helped me out a treat, Thank you
Thanks for the great comments 👍🏻👍🏻🛠
Thank you!
Thanks for the great comments👍🏻👍🏻🛠
I would replace the disk too but other than that great video :)
I Like to get all the miles out of the discs, save the planet and all that 😂👍🏻 Thanks for the great comments👍🏻👍🏻🛠
I'm about to replace my aygo brakes with borg and beck, the discs i ordered through parts in motion, yet the pads i got off amazon, the driver dropped the box with the pads in and ive now found one of the shims a little easier to move around than normal on its clips, should i rebend the clips to get it on tight or should i be fine once its clamped down in thr caliper, i'll likely be doing them and the drop links on my next day off next week, any help would be appreciated. Thanks
It should be fine once its clamped down, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 to be honest, I've just found parts in motion we're selling them for £13 less than Amazon, so I'm gonna return them as damaged just to be safe and save a few quid too as I might be needing a water pump, as I've a weird knock on the belt side of the engine though it might be rod knock but it's when I first start and when the engine is idle, what makes me think water pump is I've just changed the belt and this new one is under the correct tension as the other had stretched, I suspect you would probably agree with that analysis as the water pump pulley has seen some decent use from visual inspection and I did an oil service 2 months ago without any weird noises expect what the 1kfre engine is known for😂, some of the pinking noise has gone with a can of liqui molly fuel additive suspect carbon build up doesn't help that which you had is one of your other videos that worried me at first😂. Thanks for these repair videos
How come on autodocs video they show retaining clips but on yours there’s none?
Which clips do you mean, was it a different make of calliper Thanks for the great comments👍🏻👍🏻🛠
Nice wheels ? What size are they and where did u purchase it from? Thanks
Its all in this video czcams.com/video/IjdEhu_2j3w/video.html Thanks for the great comments👍🏻👍🏻🛠
not sure if i’m going to be able to get my hands on some big pliers to push back the brake piston, any other alternative ways of getting it back into position??
here is the link to the grips, amzn.to/389NbM1 or you can try and prize back the piston by wedging a big screw driver behind the pads while the calliper is in place, but it might be difficult.Thanks for the great comments👍🏻👍🏻🛠
Hi if you need to push the piston back in you can make a tool to do it . Get two bits of flat steel say 2 inch wide 6 inch long an 4 mil thick drill a hole thro the two bits of steel in the middle then put a nut and bolt 🔩 thro it then drill one peice again in the middle about 2 inch from one end then put another bolt thro the hole an the nut between the two bits of steel then put one peice of steel on the piston the other peice on the caliper then tighten the one 🔩 to work like a see saw one side will open up pushing the other side down pushing the piston back in to the caliper . Only cost two bits steel and two nut an bolts . 🔩
The silver thing you painted on the ends of the brake pads, what is that and is it 100% necessary if i wanted to do this at home? Thanks
Aluminium grease, you can do it without, Thanks for the great comments 👍🏻👍🏻🛠
@@aaanton11 Awesome. Thank you. And thanks for the great vids :D
Hi aaanton
Any chance you could do the wish bones on the aygo mate would really appreciate a bit of hELP with this 👍
I showed how to disconnect them on the AYGO gearbox removal video, hope that helps 👍🏻thanks for the great comments 👍🏻👍🏻🛠
Ok great
I will take a look 👍
@@aaanton11
Sorry man that video doesent hELP me at all
I have a squeaky front right break pad though it's only making a noise when I lightly press the breaks.. would this indicate the need to replace the break pads or maybe just a clean?
usually some good hard breaking will shift any debris, Thanks for the great comments👍🏻👍🏻🛠
thanks very helpful indeed
Glad it helped Thanks for the great comments👍🏻👍🏻🛠
hi, bought my aygo from 2007 for 1100 euros in nederlands... good runner today passed mot but they said front brakes need replace. I saw that the aygo originaly uses Ferodo rear brake shoes so im putting feroddo front pads. but i noticed that you don t open de brake fluid resservoar ??
You don’t need to open the fluid reservoir if the level is correct. You would expect it to be low if the pads are worn, when you retract the callipers the level will rise to the maximum. Thanks for the great comments 👍🏻👍🏻
Fantastic video!
Thanks Louise for the great comments 👍🏻🛠🛠
Can you get to the tip pens on the Peugeot 107 please
Watch all your videos all been very helpful thank you
what's a tip pen? not sure what you mean, has spell check altered something, Thanks for the great comments👍🏻👍🏻🛠
Hi,
How does wheel sensors work 2016 .. on a aygo
could u produce a video fo a replacement of a faulty senso.
Bob
I have a video on the rear hub replacement which incorporates the abs sensor, czcams.com/video/fTr4a8oz_ic/video.html I think the idea of a dedicated video to the sensors is a great idea Thanks for the great comments👍🏻👍🏻🛠
What's the make of the wheels on the aygo they look smart looking for a set for misses car
I have a video on them czcams.com/video/IjdEhu_2j3w/video.html Thanks for the great comments👍🏻👍🏻🛠
Very useful, thank you.
Thanks for watching 👍🏻
I ended up snapping my spanner trying to get a seized caliper bolt off my Aygo xD
oh no, how are the knuckles, Thanks for the great comments👍🏻👍🏻🛠
Thank you my friend!
Thanks for the great comments👍🏻👍🏻🛠
Bro I want same alloys were I buy?
video is here czcams.com/video/IjdEhu_2j3w/video.html Thanks for the great comments👍🏻👍🏻🛠
Thanks for the vid! I really like the look of those rims, what are they called?
these are calibre wheels, I have a video on the alloys,czcams.com/video/IjdEhu_2j3w/video.html , enjoy Thanks for the great comments👍🏻👍🏻🛠
With your proven ability, me & hubby class you more so as an Engineer opposite to a motor technician, if you proved warning as to what you wish to document, given the correct timing for you coupled with the car, your set up will get mega following......xx me & John , think your proving an amazing service to decent & genuine positive followers xxxxx
@@charlenepoole4869 appreciate both your support, I have loads of videos coming up due to the lock down Thanks for the great comments👍🏻👍🏻🛠
Which tyres are these ? And red pad ???were special buy ? Can you tell me plz many thanks
The tyres are hankook check out my other video on wheels and tyres, the brakes are just normal painted callipers, thanks for the great comments 👍🏻👍🏻🛠
Get a hammer and tap away those rust on the edge of the disc then wire brush them.Are these Aygo's any good? I was thinking of getting one and get rid of my 2002 Yaris.
I will replace the discs next time🔨, the AYGOs are great, just like the Yaris thanks for the great comments 👍🏻👍🏻
My car needs pads badly my light is on it pass its mot and they said my pads are low if I did it myself what to use to squeeze the caliper pistons in?
I use big grips, but have also done it with a big screwdriver, levering the calliper with the pads still inserted, give it a bash !!!👍🏻👍🏻Thanks for watching
Is there a torque setting for the wheel nuts or is it just as tight as you can get? Don't have a rattle gun
Wheel nut torque is 100nm, hope this helps, thanks for the great comments 👍🏻👍🏻🛠
@@aaanton11 cheers dude!!
That's a croky one
Thanks for the great comments👍🏻👍🏻🛠
Hi. I have an OT question. On my Aygo the air recirculation lever it's hard and I would like to oil it to prevent any issue. Do you know how to repair it? Thank you very much.
Have a look behind the dash, you will see the cable levers, pop off the cable to see if it’s the lever or the the flap that’s stiff👍🏻👍🏻
aaanton11 I'll check for it. Thank you very much.
I think it's the flap, It needs a lot wd40 but I don't know how to reach it :D.
How did you attach your number plate to the bottom grill on your aygo?
On the right side of the grille it is not hollow, so you can use long 20mm screws to reach the plastic behind the pattern 👍🏻👍🏻Thanks for watching 👍🏻
Complimenti per il video grazie e complimenti x i cerchi bellissimi mi sai dire marca e modello? Vorrei metterli sulla mia Aygo grazie
Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 what model are the alloy wheels? they are beautiful I would like to mount them on my Aygo. thanks
What’s the best way to dispose of the old pads?
Throw them in the bin😂 Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 they’re not classed as hazardous or anything like that then? Good to know 😊 Thanks.
Any idea whats the minimum thickness of the disk brake?Thank you
I believe minimum thickness is 19mm 👍🏻👍🏻
Thank you very much and btw very nice and informative video
Thanks for watching and your comments 👍🏻👍🏻
What make pads are you using?
I prefer BREMBO or Pagid, but depends on the car, sometimes the cheap ones are ok, Thanks for the great comments👍🏻👍🏻🛠
@@aaanton11 thanks for the reply I was considering Blueprint or Pagid for the Citreon C1, I think my pads are lose and making a clunk sound on braking
Nice!
Thanks for the great comments👍🏻👍🏻🛠
Hi... what size are the wheels and tyres?
I have another video devoted to the wheels and tyres worth a watch
czcams.com/video/IjdEhu_2j3w/video.html
Thanks for the comments 👍🏻👍🏻
should have changed the discs too they got big rust rings on them./
Could have changed them, but they were above the minimum thickness so next time, thanks for the great comments 👍🏻👍🏻🛠
your disc are gone to lol... why ditten you change them ?
That will be in another video, Thanks for the great information👍🏻👍🏻🛠
Those brake disks are cheap i would just change them too.
Thanks for the great information👍🏻👍🏻🛠
Those brake discs had to be changed for 2 years already
😂Thanks for the great information👍🏻👍🏻🛠
@@aaanton11 🤣
Name of rims ?
Calibre, I have another video on them, check it out, thanks for the great comments 👍🏻👍🏻🛠
Them brake discs need changing.
😂 Thanks for the great information👍🏻👍🏻🛠
What about disc brakes??? New pads on these terrible disc??
If they are above the minimum recommend thickness and don’t judder, why change them, you are just throwing money away 💰👍🏻
You should have chipped the build up of rust off the discs, new pads just get torn at edges.
Just for you, when the pads wear out again I will replace the discs lol
i bib my horn all the time acciidentally
Always doing it 😂 thanks for the great comments 👍🏻👍🏻🛠
Hi mate. My front o/s brakes are very rattly when going over rough roads. I've linked a video below showing the noise they make.
czcams.com/video/9LypBMFV78w/video.html
I took the pads out and put them back in the other day, the noise disappeared for a couple of days but has come back. Any idea what the issue would be? Cheap pads? The pads are just over a year old.
Thanks for the video, you need to remove the bolt , lift the Caliper, then pull out the slider as in the video 9.08 but pull it all the way out, the rubber boot pops off, pack it with copper grease and refilt, I would do top and bottom sliders, hope this helps👍🏻👍🏻🛠
UK WEATHER IS TERRIBLE FOR CARS ....... RUST IS THE ENEMY. BEAUTIFUL WHEELS ... WITH CENTER CUP?....MANUFACTURER?
these are the calibre wheels, Thanks for the great comments👍🏻👍🏻🛠
An amateur's work. Discs is completely worn and rusty - must be replaced! New brake pads won't do it alone.
If they are above minimum thickness and don’t judder, why change them!, you are just throwing money away 💰 they have been on the car for over 12 months with no issues. Thanks for the great comments 👍🏻👍🏻🛠