PCM ZZ6 OIL CHANGE!! DIY Series, Episode 21
Vložit
- čas přidán 23. 08. 2024
- MERCH!! www.wakemann.com
Instagram: @wake_mann www.instagram....
WAKEBOAT OWNERSHIP: czcams.com/users/pl...
DIY SERIES: czcams.com/users/pl...
TRICK TIPS: czcams.com/users/pl...
SHOP-DOMINIUM: • Shop-Dominium
Email address for business inquiries: wakemanninfo@gmail.com
Mailing address:
724 15th St W
PO Box 20042
Billings, MT 59102 -
Other ways to support the channel:
Use discount code WAKEMANN at www.wakelife.co
Provide branded merchandise to your audience without carrying inventory using Printful: www.printful.c....
Idaho Water Sports: If you are interested in purchasing a boat please
check idahowatersports.com and take a look at the
inventory. I can also help you with ordering a new
customized boat. Please email me at
wakemanninfo@gmail.com. If you work with me
to buy a boat from Idaho Water Sports I will send you
some WAKE MANN gear!
Do you want to help the channel grow? If your answer is Yes, you can always donate to the channel by sending money via Venmo to @Tim-Mann-4
I guarantee every dollar donated to the channel will go directly to enhancing the content of the channel. Thank you for your support!
Thanks for the video it was very helpful.
@@liviubeleuta4227 you're welcome!
Just did my ZR6 PCM oil change last week on my ole 08 SAN 230. Had more access room. I did warm up the motor in advance to allow for easy drainage. I didn't have an extractor. That 15-40 oil doesn't like to drain when cold. But it does come out nicely when hot without a pump. I tried a drill pump once.... What a mess and it didn't work well. Got my filter from Napa. All good. 950 hrs on the motor when I did it.
Awesome, congrats on 950 hours!
Love your channel. For even easier/ less messier oil changes I got a barbed fitting with a hose clamp to attach to the hose in my oil pump then got a female to female fitting so that it can be treaded directly to the oil drain hose
Thank you! Awesome, I actually had a very similar setup for my first wake boat.
@@wake_mann No problem! Absolutely love the color combo of the nautique! Your content is great to!
Thank you!!
Thanks for the video! Looks like I’ll be using your video to guide me as I perform the 25 hour service on my new G23 since my local nautique dealer doesn’t have any Service appointments available for the next 8 weeks!!
You're welcome! You got it easy.
@@wake_mann the dealer said the 25hr service was an oil and filter change. Is the transmission fluid also recommended?
@jaylarson4465 I would have to check the manual but I believe it is a step to change Trans fluid at break in service.
Just did a tune up too! I went with a self lubricating blue impeller that supposedly can run 15mins dry!!!( not that I’ll ever test that). And my boat specs a weird weight that only comes in dino or semi synthetic… so I run the full synthetic 5w40 amsoil…
Amsoil is the only brand of oil we used in our planes. If go up to the edwards jet center, in their shop… you’ll see its the only oil they use too. And good job doing this yourself.
Nice, amsoil must be a good oil.
Are you not able to gravity drain the oil pan on this one if you didn't want to buy the extractor pump? I run that drain hose down through my plug hole on my old direct drive, is that not a viable option on your v drive?
Out of the 2 Nautique's I've owned this is not possible as Nautique only has 1 center drain and no rear drain. The pigtail does not reach. I was able to gravity drain on all of the Malibus I owned though.
WM - Thanks for these videos. Can you please do raw water impeller and ballast pump impellers someday 😁
Yw, I will definitely do a raw water impeller this winter but hoping I never need to do a ballast impeller, haha.
WM - If this is your break in (first 25 hour) service, I think it’s really important for you to do one important item. Check your drive alignment. The engine mounts settle in quickly (heat and vibration) and can cause a mis alignment. Your v drive bearings will thank you down the road.
Thanks for the tip!
Joe - How do you check drive alignment on 2022 G23?
ZZ6 big enough? Or wish you would’ve gotten the ZR7?
Does doing your own oil change void the warranty?
Valid question. I think it could void your warranty if you screw up your engine and its obviously from your maintenance, otherwise it should not.
WM - Google: Under the Magnuson-Moss Warranty Act, it is against federal law for car dealers or warranty providers to deny a claim or void a warranty because vehicle maintenance was performed by the owner.Dec 15, 2021. You can check if this applies to boats but i think it does.
A friend of mine takes combo photos of hours and hours written and initialed on the filters. And more when in place.
It's cool that you do all this yourself, we aren't brave enough haha! Not related, but we are currently searching for a prop. Heard so many mixed opinions lol and am very conflicted. Rewatched your prop video and it helped, so thanks! In your past experiences, how long has it taken you to get your prop from wakemakers?
I had to get comfortable with it because it's that or miss a week or 2 or maybe more of riding. Awesome my prop video helped you. As long as wakemakers has the prop in stock, I would expect it to be able to get to you within a week.
@@wake_mann 👍🏻 Thanks Tim! Unfortunately dented out prop pulling into my uncles lift. Dinged it up pretty good. My dad and I were fighting to get it off the boat haha, the prop puller was missing a part so made it extremely difficult lol.
@@SupremeSurfers sorry to hear, you can send props to ACME to get repaired if they aren't too bad. It's much cheaper than a new prop typically.
My dad works at PCM in sc
Thats cool, I bet it's a cool job.
@@wake_mann no I’ve been going with him for the past week and just a lot of talking and typing
Oh haha, sounds like my job
@@wake_mann what do you do?
I work for Fiserv, data processing for banks. I am on the phone with bankers all the time and on a computer.
ZZ6 big enough? Or wish you would’ve gotten the ZR7?
Certainly big enough for me at 3600 ft. Many people confuse ballast capacity and people capacity. Ballast is people replacement weight. If you load your boat up with max people capacity and max ballast capacity and expect your boat to perform well you are thinking incorrectly. My G23 with the ZZ6 has 3500 lbs below deck ballast plus my 150 lbs of wife and daughter and does very well while creating huge wakes and waves.