My 2 cents. Don't waste time on 1:00. There's no need to remove the rubber element. Simply unscrew the Torx over the rubber. It's simpler, faster and both components never need to come apart or get lost. BTW the rubber already as a pass through hole, on the center, precisely for that. Cheers ;-)
Great Peugeot 107 videos. Have you experienced noise issues coming from the engine room (rattling noise) just around 2800-3000 rpm? Or do you know what can cause that?
A ok, that sucks. Ill try to record the noise and upload a video. Just read that in UK - Department for Transport that they have a Recall for Peugeot 107 con-rod bearing: www.dft.gov.uk/vosa/apps/recalls/searches/expand.asp?uniqueID=3F7DF112AA6E56A180257AA90031F978&freeText=Blank&tx=0.8505976
This engine is 3 cylinder and have a natural unbalanced vibration that give a bit of noise the engine have a very good internals and lubrication system rarely give crank problems. A have 6 of them and rent them out I even have the oil service interval extended to 30 000 km with full synthetic oil. But then I flush the engine properly to clean it out inside when I replace the oil
Pokaż jak wyciągnąć plastikowe nity łączące zderzak z błotnikiem i nadkolem. Próbowałem to zrobić i w przednim i tylnym zderzaku i był to czysty horror:-(
Can I only remove the bumper without the rear lights? I did the rear lights today and the thirds light yesterday, but it's still leaking so must be grids....
No, you need to remove the rear lights before removing the bumper. Did you see this? I tried all kind of sealing and only changing the window seal helped czcams.com/video/hQZzO-3m4w4/video.html&ab_channel=FixandDrive
Almost everything on the triplets is interchangeable. With some notorious exceptions. The rear bumper cover being one of the exceptions, that don't fit. Notice where it meet the rear lights. On the other hand the fixing points are exactly the same!
My 2 cents. Don't waste time on 1:00. There's no need to remove the rubber element.
Simply unscrew the Torx over the rubber. It's simpler, faster and both components never need to come apart or get lost. BTW the rubber already as a pass through hole, on the center, precisely for that. Cheers ;-)
This was really helpful and saved me lots of time - PayPal donation sent, purely for the effort you saved me working on an unfamiliar car! 👍🏻
Thanks
Great video and easy to follow. Bumper from my 107 removed, vents resealed and bumper replaced. 👍
Nice and clear video, thank you
Great stuff! Good video, easy to follow, helped me a lot. Thank you!
👍👍👍
Thank you. Good help!
Great Peugeot 107 videos. Have you experienced noise issues coming from the engine room (rattling noise) just around 2800-3000 rpm? Or do you know what can cause that?
I've heard of a 2-3 cases, mate. Sadly they were all crankshaft bearing issues. Looks like they crack sometimes.
A ok, that sucks. Ill try to record the noise and upload a video. Just read that in UK - Department
for Transport that they have a Recall for Peugeot 107 con-rod bearing:
www.dft.gov.uk/vosa/apps/recalls/searches/expand.asp?uniqueID=3F7DF112AA6E56A180257AA90031F978&freeText=Blank&tx=0.8505976
This engine is 3 cylinder and have a natural unbalanced vibration that give a bit of noise the engine have a very good internals and lubrication system rarely give crank problems. A have 6 of them and rent them out I even have the oil service interval extended to 30 000 km with full synthetic oil. But then I flush the engine properly to clean it out inside when I replace the oil
Czy w tym aucie tez bł woda w bagażniku?
Nie.
Hi I have a 107 and all the locks don't work or even turn any ideas why as I need to remove my bumper but can't any help would be appreciated thanks.
Still can't get that connection undone ...you should show how you did it
Pokaż jak wyciągnąć plastikowe nity łączące zderzak z błotnikiem i nadkolem. Próbowałem to zrobić i w przednim i tylnym zderzaku i był to czysty horror:-(
też zerwałem, kupiłem zamienniki
Can I only remove the bumper without the rear lights? I did the rear lights today and the thirds light yesterday, but it's still leaking so must be grids....
No, you need to remove the rear lights before removing the bumper.
Did you see this? I tried all kind of sealing and only changing the window seal helped
czcams.com/video/hQZzO-3m4w4/video.html&ab_channel=FixandDrive
Eccellent
Is the bamper from 107 the same as Aygo (1st generation)? And can be replaced instead
Almost everything on the triplets is interchangeable. With some notorious exceptions. The rear bumper cover being one of the exceptions, that don't fit. Notice where it meet the rear lights. On the other hand the fixing points are exactly the same!
Thanks. Does this apply for 2010 Argo?
Pretty much the same.
Do you know how to remove the fuel flap? Is it bolted or riveted?
I am also interested in this question🤔
I would've cleaned the car underneath the bumper and lights...