How to break in a brand new Suzuki Outboard Motor
Vložit
- čas přidán 10. 07. 2024
- Here is the perfect instruction on how to break in a brand new Suzuki Outboard motor. The process is fairly simple but very important, to say the least. following these simple steps help seat the piston and make sure the motor adapts accordingly. Not following these instructions could lead to piston or motor failure and could void your warranty. Here are the steps in perfect sequence:
Step 1: Idle the engine in gear for 15 minutes or longer, keep the RPMs low.
Step 2: Run the boat for one hour and forty-five minutes at 3000 RPMs. Do not exceed 3000.
Step 3: Run the boat at 4000 RPMs for one hour. Do not exceed the 4000 RPMs.
Step 4: Operate the boat normally but do not run at full RPMs for longer than five minutes. It's best to fluctuate the RPMs and do this for the next seven hours.
That is all there is to properly break in your new Suzuki. I must admit, I have been very satisfied with my purchase thus far and look forward to years of reliability.
www.onsitemarineonline.com/
/ chris_onsit...
Address: 1114 N U.S. Hwy 41, Ruskin, FL 33570
Phone: (813) 944-8662
#suzukibreakin #300suzuki #howtobreakinoutboard
0:00 Intro
0:53 Step one motor break-in
2:20 Step two Suzuki break-in
3:33 Final break-in step
4:37 Run FULL Speed
5:27 Close
▬▬▬▬▬▬▬ SUBSCRIBE ▬▬▬▬▬▬▬
Click Here to Subscribe! ► / fishing19. .
NEW FISHING VIDEOS EVERY SUNDAY!
▬▬▬▬▬▬▬ WEBSITE ▬▬▬▬▬▬▬
Official Website → saltyscales.com
▬▬▬▬▬▬▬ STAY CONNECTED ▬▬▬▬▬▬▬
Twitter → / saltyscales
Instagram → /
FaceBook → /
Google+ → plus.google.com/+Saltyscales/....
** Use & search hashtag: #SALTYSCALES **
▬▬▬▬▬▬▬ SUPPORT OUR SPONSORS ▬▬▬▬▬▬▬
• Okuma Fishing Tackle → okumafishingusa.com/
• Castaway Customs→www.castawaycustoms.com
• Badfish → www.badfishsupply.com/?rfsn=4....
• Power Pole → www.power-pole.com/
• Onsite Marine → www.onsitemarineonline.com/
• Down South Lures → downsouthlures.com/
▬▬▬▬▬▬▬ BUSINESS INQUIRIES ▬▬▬▬▬▬▬
Email Address → JOSHUA@SALTYSCALES.COM - Sport
Just finished the first 3 hours of break-in on my new twin 250's now for the remaining 7 :)
Watched this video when it first dropped, Bought my 2005 24' CC Sea Pro Bay Boat in need of a re power earlier this summer and just this week, Took it to Chris @ On Site in Ruskin, he seems awesome, straight forward, knowledgeable and fair. Boat is there now for a new White 250 and a Bobs Action jack plate combo, probably be done next week and I get to do the break-in between Christmas and New Years. Living in Bradenton Ruskin was a short drive and worth it !! Enjoy your videos and good be able to patronize someone you deal with locally.
Fantastic, he should take care of you.
thank you great video im getting a 200 suzuki for my new boat being built a pair custom 21
Kudos to Chris for taking 5 hours out of his day for breaking in that engine, most outboard shops would have you do it on your own time. Also I would look into that spray coming off the powerpole spraying onto the motor.
Good guy for sure. The spray is from the transducer but we manged to get it positioned properly.
@@Saltyscales nice i know a guy who had a new f150 corrode out quickly due to a transducer spraying like that
@@gulfcoastsurf I beleive it, that is why I wanted to get it fixed asap. She is all good now. 👍
Awesome captain 👍🏾
Thanks bud
Fire thumbnail 💯 congrats on the new zuki zuki
Thanks buddy
That 80% off sounds really nice on a 200hp.
Awesome, ....
Do i need to change oil after the first 20 hours? And how do i know i’ve reached 20 hours if i have the regular rpm gauge and not the digital one? Will the oil light turn on?
Thanks!
Thanks for creating this video.
If someone doesn't have enough time to do the run-in after 3000rpm, say, and then comes back another day to do the 4000rpm, should they go through the 15min idle also?
How long is it recommended to warm up an engine (eg 140hp) before driving off, normally?
Thanks again
We missed the boat parade. :( Go Bucs and to you, the boat is looking good just too bad she's off the water again being worked on.
She will be back!
Awesome
Hey Josh. That first three hours had to seem sooo long..lol. I know you, you were ready to just go.. But gotta do things the way you have to go just to expensive not too. Great video Josh and thanks for sharing.. Always your friend, fan, and subscriber..
I am impatient but know the importance. We had a good time so it was all good.
Very nice. I had to get a new 200 Suzuki this week. Can't wait to try it out
How are you liking your 200hp
@@Honda1k oh I love it. I cruise at 42mph
@50 Shades Of Blue 42mph nice!! What kind of boat? I'm in the process of repowering with a 200ap. Coming from a mercury 200hp 2stroke worried I'm going to lose some mph but excited. I have been wanting a 4stroke for a long time now.
@@Honda1k I’m running it on a Sea Pro SV2100. It’s a pretty light boat and max at about 49mph. Super quite engine. I let it sit for six months once and it didn’t skip a beat and fired right up. I’m always on other boats so I don’t always get to use mine
Hi Josh, HEY ~ nice wrap on your steering wheel. So sorry to hear how Boring breaking in a motor can be. I mean out in a boat All day does seem like a real drag! lol Now your all done and ready to go. Hope you will be happy with the new Power Plant. BTW, CZcams is up to not sending out notifications when your videos drop. (At least for me. I missed this one and the previous one.) Take Care my friends. Stay Well and God Bless ✝
So far so good. Should slay a bunch of fish. 👌
@@Saltyscales Hey Josh, my bad. It wasn't until after I wrote the comment that I realized it isn't a wrap. DUH!!! 😆
This winter at the MN boat show, I decided to re-power my boat with a 140HP Suzuki. Traded in my 150HP Johnson 2 stroke. I have not had it on the water yet (next week hopefully 10 Apr 24) Have to do the break-in. Can't wait to get it wet!
How do you like it?
@@207shenanigans Love it. Runs very quiet. very smooth
@@bgronni1where did you do it? I am looking to do the same in MN.
@@smiley3303 I did mine in April on the St Croix and Mississippi river. you can go a long way at a constant speed. Of course this was before the floods.
@@bgronni1 I meant the dealer you used!
Repowered my action craft flatsmaster with a 150 Suzuki...love it! Always wanted a four stroke. I hope yours treats you a good as mine is treating me.
I feel good about the purchase. We will see. 👍
What size flatsmaster?
@@grantgauvreau2744 1820
Had to remove the poling platform
Will the breakin still work by following the manuel instructions?
What is attached to your lanyard?
what oil did you use for the break in? Book says ecstar 10w30/10w40 or equivalent. Been doing a little poking around and 90% of marinas, suzuki outboard mechanics..ect say to use 100% conventional for break in.
So the last 7 hours you can run to your favourite fishing spots and stop and fish for the rest of the break-in?
Cant wait for my repower with my new suzuki - df300btx5- buying it from chris at on-site
Awesome, he should take good care of you.
Hey Josh
I have a new Suzuki 140 my question is do I have to run at those rpms the whole time or just not to exceed those rpms? Just wondering if hit no wakes can I go from 3000 to idle for a while then back to 3000?
I have a small 20 HP Suzuki. Do you recommend the same warm up time? Also is this break in all during the same day or can I separate it out?
Same applies, you can break it in at different intervals.
*Josh... I didn't see the "in" part of break in when I saw the title header... So, the first thing I thought was that this was going to be a Chris-cuss-out-in-up--down-sideways...The Header really does change if you remove or you don't see the "in" part of it* ..gw
😂😂😂
Not bad, need a marine company near me that treats their customers like them
Chris is a good guy, he takes good care of his customers.
Fix the transducer splashing the sea water onto the engine. Garmin makes a transducer cover to fix this issue.
Fixed a long time ago, don't even own that boat anymore
Judging by the hat...subbed. Back the blue!
Where did you get it installed? I live in the Tampa Bay Area to.
Onsight marine in Ruskin, tell them we sent you. He'll take care of you. 👍
I was only able to get into the 1.45 hours at 3K R/PM and had to pack up for the day. Can I finish my last stage of 4K R/PM in the morning like I had planned?
I for the most part stayed at 3K for 1.45 hrs with maybe 10-15 minutes of reduced idle in that whole time, is this also ok? Thanks!
Hello Steve, you can do the remainder on another day. It doesn't have to all be at once.
@@Saltyscales just wanted to make sure, I did not see in the manual that it can or can’t be done this way. Do you think I got enough reduced throttle in the first procedure?
Just bought a Suzuki. I have a question if you don’t mind. Do you have to drive for one hour and forty five minutes at 3000 RPM continuously or can you do it in stages?
You can do it in stages
does the HOURS have to be straight, or can you break it up? So take it up to 3000RPM for 1.45 hours or 30 minutes here 30 minutes there?
I was wondering the same thing..... I hope you get a reply
It doesn’t have to be continuous, ideally if you have the time or the location to make a run that long continuous would be best, but smaller lakes that’s just not possible. I think as long as you go the recommended hours at the recommended RPM it could be achieved in multiple trips. Just keep a log and follow it to a T, those computers under the cowling know exactly what RPM ranges are ran and for how long, if not broken in properly Suzuki could push back on a warranty claim, Good luck
I just got my brand new boat today. Its a 2022 so its a leftover. The dealer said he took it out the day before I showed up to get it. He said he ran it a bit and got it up on plane and maxed out the rpms for a minute. He didnt say anything about breaking it in or letting it idle first. Is this going to void my warranty? Should i be concerned or should i just go through the break in process? Thank you in advance
Definitely go through the break-in process. They can see from the computer if it was done.
Thank you
👍
Can i do the 7 hours on another day or preferably same day?
It can be split up.
What does it mean when the motor vibrates?
Bent Prop
“ How to break in a new motor !” Load boat with enough provisions for four days , fill up gas tank ! And take extra gas , take plenty of bait and ice, drive to choice locations and cast repeatedly till arm wants to fall off , return to port load boat , and clean mass amounts of fish , oh and explain to you wife and kids why your smiling all the time ! 👍🏼😁
Lol...love it 👌
These motors last 6-10,000 hours so that break-in period should be worth it.
Suzuki over Yamaha every time 👍
need to fix whatever is causing spray on to the side of your outboard something is dragging kicking up water
Transducer, it was fixed. 👍
@@Saltyscales good to hear i had issues with setup on my outboard had to move it up to get rid of spray. So i know the struggle of setting the boat up lol
You going fishing? Nope I’m going on a 10 hour motor break in 🤯🤯🤯no fishin?😵😵😵
Ordered Two DF175AF's 6 weeks ago for my 25' Refurbishment - where's my motors Suzuki....?????
They had mine in stock, it was pretty fast.
@@Saltyscales cool- give them a call for me and tell them to get the motors to Fort Walton beach asap cause 8 weeks is way to long.
lol. %80 off
🤐🤐🤐
How to waste 100 bucks of fuel
Yup and it has to be done.
hahahahah seafog Geoengineered crap hahahahahahha wake up
what a bunch of bs. this isn't needed
Okay lol. Tell the manufacturer that. 🤦♂️
Until they blow you off for a warranty claim.