DIY VACUUM FORMED STENCILS FOR CRANKBAIT PAINTING
Vložit
- čas přidán 7. 09. 2024
- DIY VACUUM FORMED STENCILS
MAKING YOUR OWE STENCILS FOR LURE ART IS NOT A COMPLICATED PROCESS BUT FOR THE BEGINNER I HAVE CREATED A INFORMATIVE VIDEO ABOUT HOW TO FORM A STENCIL AROUND THE LURE OF CHOICE WITH MOST PRODUCTS YOU HAVE AT HOME.
Updated Link for Plastic sheets: amzn.to/3r0i2DG
heat gun I use: www.harborfrei...
Links to other videos:
picking 1st airbrush: • PICKING YOUR FIRST AIR...
Airbrush paint selection: • Selecting Airbrush Pai...
Products to use as stencils: • TUTORIAL ON PRODUCTS U...
Thanks for stopping by, please leave comments and suggestions below.
The links below are affiliate links and I may receive a small commission which helps me continue providing great content to you.
---------Products I use---------
Master g22 starter brush: amzn.to/3dctQ1z
Iwata eclipse: amzn.to/3baTYaf
Iwata air compressor: amzn.to/3jQha1D
Iwata airbrush cleaner: amzn.to/3qntPLZ
Airbrush holder: amzn.to/3aoZ5EV
Airbrush Cleaning tools: amzn.to/3plOtL5
Cheap Airbrush hose: amzn.to/3artmmB
High quality hose: amzn.to/3tXP5tU
4 way manifold for multiple brushes: amzn.to/3pgN6xi
Blower motor for paint booth: amzn.to/2ZpzEfP
Createx paint----
Opaque starter set: amzn.to/3dfjSMN
Transparent starter set: amzn.to/3rTsTPK
Fluorescent set: amzn.to/3rX03hC
Createx wicked starter set: amzn.to/2NuWDDy
Wicked Iridescent: amzn.to/3rX1HzO
Wicked pearl starter set: amzn.to/2LRRZz8
Auto air by createx: amzn.to/3pj7ZYN
Autoair Candy: amzn.to/3u1lQq3 ( good set but may need few additional )
Paint---(not above but need)
Sepia: amzn.to/3pp8VKW
Magenta black: amzn.to/3alg2zL
Moss green: amzn.to/3pl0lwL
Stencils-------
Artool mini- amzn.to/3u4795x
Texture fx: amzn.to/3phULeI
Insane Custom stencils: www.insanecust...
Clear coat-----
KBS: amzn.to/3jRd753
tamco : tamcopaint.com...
Camera and Gear-----
Go pro 7: amzn.to/37gZkj7
Nikon d3300: amzn.to/2ZgPfyv
35mm lens: amzn.to/3plWxLR
Rode compact mic: amzn.to/3amM92n
Rode wireless lavalier mic: amzn.to/2OIp2H1
Cheap lavalier corded:amzn.to/3rYK2b0
K&F tripod: amzn.to/3rOd0Ku
Editing equipment---
Computer: amzn.to/2LRkXiA
Davinci Resolve studio: amzn.to/3jTh9K8
My contact info:
green country baits
105251 S. 4580 rd.
Vian, ok 74962
Social sites:
Instagram: greencountrycustom
Tweeter: @jstreun36
website: www.greencountrybaits.com
Can't believe I just found you guys. I have been fighting with my Dremel and my stencil burning tool to make these Christmas presents and I can't believe how much I have been doing to make my life harder lol thanks
Glad the video helped.
Great video… thorough instruction and great idea!!! Thanks man! Your work space is WICKED😮
Just a small space in garage. after many years you figure out what works and what hasn’t.. thanks for comment
I just started painting lures and making vacuum stencils. I haven't used the framing technique, but I see how that can make it much simpler. I absolutely love the simplicity of your videos. It's amazing how much you can learn from such simple videos without all the extra hoopla thrown in. I don't sand those edges on my craw stencils, the rough jagged look makes it so realistic! I use a soldering gun to melt the template for my cutouts. I already have guys lined up wanting to buy my lures.
Glad you value the videos kevin. The frame is simple but several other ways to get good results just they way I do it. Thank you for watching
I really like that frame idea.
GLAD I COULD HELP
This is the answer to my prayers Thanks.
Glad it helped.
I use the same technique by utilizing a frame to hold the thermoplastic in place. I also use a hot knife which comes with a soldering kit you can purchase at Walmart. Makes very clean cuts and almost like using a pencil
Great tip thank you for comment
That was awesome..great work and thanks for sharing..
Glad you enjoyed it. Thanks for watching
I have the same basic set-up except I cut the baits I use for the mold in half.I actually sacrifice two baits because when you use the Dremel cutting wheel you want to cut offset to the center of the bait to get a true half that will lay flat when heat forming. So to get two true halves you need to use another bait and cut offset to the center line on the opposite side of that bait. Another tip is sometimes, when applying heat, you can melt or warp the bait you're using for a mold. I solved that by packing the bait half with milliputt putty. The putty dries rock hard. Your mold bait won't melt or warp and you actually pick up a little more detail on the vacuum formed stencil shell because the milliput putty warms as well during the process.
Great info thanks for leaving comment.
i havent tried it yet read where a needle mounted on the end of soldering stick might work and be cleaner and less work i used the air high speed dentist drill, but those burrs/rough edges are a pain to get perfect,and if you leave the smallest amount , it will raise stencil up causing bleed through, great video
Yes they make a stencil cutter that is basically a soldering iron with a small tip. I will do video on that soon. Not perfect melted edges are ruff also but it is another way.
I saw where the lure making plant has a set of tongs with a stencil for both sides at once. I wish I could figure that out
Have not seen that
Thanks that was cool
Glad you liked it
Gran bel video veramente...che materiale usi per fare lo stencil?e che punte sono quelle che usi col dremel per intagliare??grazie
What was the number dremel bit you used? Thanks
very small i can’t even read it now. its was a set purchased from harbor freight, and they still sell that kit.
Lol how did you put together the wood frame? I had a lot of plastic but it all curled up.
You can just buy two wood picture frames and place plastic between and add wood screws to each side how i made my first one
Jeff, where do you get your vacuum forming sheets and what mm do you use?
Thanks, David Pickell
David been so long I can’t remember but i have a link in video description. I haven’t checked it in a while so not sure if still good link
I use empty milk containers a 6 pint one gets u enough for 2 baits the stuff in sheet form is pricey.
I will try that out Peter. Thanks for comment
I also need to know what those drimal bits look like ty
They are micro carbide bits that are from harbor freight
What’s that rattling ever few seconds?
Not sure old video. Probably old air compressor
You didn't show making 2 of those. Did you make them both at the same time? Or did you make the second one off video?
Made 2nd off video. yes need both right and left side
@@greencountrycustoms8387 thank you
What thickness of stencil sheet do you use? And where do you get these - I’m looking at Amazon?
amazon link in all video descriptions I can’t remember the thickness
What type of bit do you use for it? What would I search to find something like that?
I use what is called micro carbide bits, i purchase them from harbor freight.
Ever get the correct link to the plastic sheeting
No haven’t approved of any I’ve ordered since first batch. Plastic milk jugs work well. I will look into it again all been to thick
Where did you get the speed trap blank?
They are not blanks those are the real deal Pre -rapala traps. 1/4 ounces have all be painted and sold have a lot of the smaller size.
why don't you leave them in the frame when you drill them out?
You could but the thermal plastic is rigid and the frame isn’t needed except to keep the heated material from curling up until cooled.
How much to paint a few Scranks?
go to www.greencountrybaits.com all info there. depends on pattern and if your sending lures or not.
How thick is the wood?
It is 1/4 inch pieces i ripped. you can buy 2 small wood picture frames and get same thing it is just something to hold plastic firm while melting occurs so it does'nt curl up
I went to the link you sent me to and there was 3 sheets and it is Wayyyyyy to thick man! I am ticked off
I will check the link.
The plastic in your description i paid 20 dollars for is 1/16" Thick WHITE! Not clear. Looks 2 time's thicker than what you are using! You said you would try to drop a link. You did and i wasted 20 dollars and alot of my time. Can you please tell me the right link to get the right plastic from and clear! I wander how many others purchased the same damn plastic and lost money! Some bad info. Good video with the materials that you are using but some very bad info. Also we have no clue what bits you are using in that dremal
When i purchase i copy the link and paste not sure what could have happened but will investigate and provide update.
thank you for bringing to my attention, a new link has been added. contact my email and i will settle up with you.