I am just in awe of the skill this man has.. Eventho it’s not all flawless, he did convert and “rebuild” a whole car, just to be able to relocate his plant.. 😅 you have to be able to pull it all of in the end !! Awesome build❤❤
That reminds me of earlier in the 70s, when we welded rusty cars like this back together in Germany... but we had to go to the technical inspection with it... installing the rims the wrong way would have been an absolute absurdity... even though the colleague acted very brutally, but still he deserves a medal for welding with electrodes...all respect! 🥇🏆... we used acetylene and oxygen for welding, until the mig mag or the wire welders came up. he did a lot of work, disassembled everything... he could have worked a little nicer... but he's still a talent👌😎
You are very polite. I respect the time Mr.Hô engaged into this conversion/restoration BUT it is not a proper work. In the mad Europe, the German TÜV would NEVER APPROVE this car. To me the worst about this car is the suppresion of structure bars in the trunks.
@@alexandrhrouz666 Early in the 70's doesn't mean "today". Nowadays, it is not about the police but about the official check to allow your car on the roads.
Welding sheet metal with a stick welder isn't easy. It looks great, however, I am concerned about the rear shock towers not being strong enough. How do you plan to get at the mounting nuts now that they are covered with fiberglass?
Một trong những kênh CZcams đáng xem nhất Vn nhưng hầu hết khán giả đều là người nước ngoài vì sao? Vì nước ngoài thích tài năng khoa học kỹ thuật sáng tạo chứ không phải những cái vô bổ câu like câu view
Vì người nước ngoại ko có thợ lặt vặt như vn. Bên mỹ làm gì cũng phải có bằng. Ko như VN. Lên họ ko biết sửa chữa lên thíc xem video này. Vn thì đầy việc bạn thíc học sửa chữa oto miễn phí cũng có
1) как заменить в случае дтп задние фонари 2) как заменить в случае неисправности задние стойки 3) ручку задней двери можно было заварить, и зашпаклевать 4) зазоры на задней двери можно было сделать тоже самое что и с ручками 5) развернуть колеса и установить странное решение Есть много недочетов я так понимаю авто было сделанно только для контента. Но многие и такое не смогут сделать.
As always, your work is nothing short of amazing. You put a great deal of hands on engineering into your work, and the level of ability & knowledge is simply priceless. I was hoping the rear doors would have been sealed up to look like a factory ute also, but if it was intended to identify a modified sedan, then i get it 😁well done bro, fantastic job. Here in Australia, unfortunately, it would never pass an engineers modification certificate. There is a big list of structural compliance and requirements that must be met before they even look at the project. But who cares, You're not in Australia 😂
Good job Mr ho I weld and fabricate trailers myself and I much appreciate how you do your videos all the process at once as compared to seeing months worth of videos in real time it is better for me to see the entire process in a timelapse version
This is pretty amazing. And I say this as someone who worked around body shops selling PB&E for years. I've seen a few conversions of this type done, and the only thing I can say that I would do differently would be a little stronger material at the top of the rear shock/strut towers and a heavier box system to tie the two upper rear towers together (probably a u shaped box to go under the rear window, with a couple of pillars down to the floor "frame"). Without it, I see some flex issues on the body/chassis, but overall it's amazing. I see some rust I would have cut out replaced as well to make it structurally stronger, but overall, I get the "where do I stop" question on an old beater like this... Also, MAD PROPS for using the stick welder on your sheet metal!
Nice idea 👍 Shame the rear towers didn't get reinforced, and then get completely covered with fibreglass! Lots of issues, with body, suspension, steering, even those rear lights are half done... Nice idea, just a bit rushed.
Don’t you recognize that all tool and equipment he have is : grinder , welder , antique hammer , and some very basis tool ? The point is he did an amazing job with what ever he has on hand which nothing .
I'd use the trunk lid and the piece of the roof to make a removable tonneau cover for the new bed. also since the bed seems to be water tight you might want to drill one or two small drain holes at the lowest end of it for rain and any spills.
not downing him in this video and (Imm not good at that stuff ) but the door handsfor the back and the back door outline i would of try to bondo all of it where it look more cooler like it was really made like that but thats cool little truck
I appreciate the time to retrofit this vehicle and make the video. Yes there are things I would do differently, but well done, keep improving. Blessings from the Caribbean.
Check out Merlin’s Old School Garage channel. He took a Volkswagen Jetta and made a ute. He used a kit. It’s pretty interesting. Here in the states, we don’t see that much. However, I would drive one. Cool looking trucks….
I like the conversion a lot! Excellent planning, but I see that the turning is going to be an issue. Also the rear door handles and door gaps could have been filled at one point to where it would look like a factory offering.
@@franksanta-teresa971 also how does he adjust the rear shocks because it appears he fiberglassed over them, they should be covered but made a removable cover for repair
NO D.O.T (Department Of Transportation) regulations we love 3th World Countries.. Just paying for tags once..free rides for ever.. ahhhhhh.. Much love from USA United States of America ahhhhhh
Прикольный пепелац получился, по дешману пойдёт. Но я бы заварил задние двери, убрал бы задние внутренние арки заменив пружины на торсионы, тогда бы и погрузочный объем бы увеличился. Заменил обычный ручник на электро ручник, тогда бы можно было поставить задний диван в салон вместо двух седений. Для мультимедиа сделал бы подиум и перенёс бы наверх вместо часов.
If you had the hatch 4 door, or the tailgate from a Corolla FX, you could make a gate to extend the bed into the passenger compartment for larger items. My family had an 84 Corolla back when it was brand new. I had an 88 FX AE88.
Awesome!! Love seeing stuff like this and your really the only one I've seen doing it. Maybe you should update along the way? Just do extra stuff to it and post videos. I know me and a lot of others would love to see it. But great jib man!! I'd drive it and use it all the time !!
I like it alot man your work is amazing! If i might suggest weld that door full so there is no more door line, and remove handel and also make it smooth. That way it would look more like one panel. Its only my personal opinion, but like i said man great work!
Fantastic transformation and effort :) I just would have added some tie-down points in the back to secure loads safely. Also a drain hole somewhere with all the rain you get :)
My grandpa did basically the same thing to an old four-door sedan he had years ago when I was a kid. The main difference is he left the back doors where they opened. That way he could load stuff from the side without lifting it over if he had to.
Тачка металлолом, побыстрому решил продлить ей жизнь не на долго и просмотров срубить за одно, с их влажным климатом она за 5 лет в труху рассыпется после такого "ремонта".
Gorgeous! Really enjoyed the yellow color. Even though the black and white "dream" at the beginning showed the design, that yellow was a beautiful surprise when you started painting!
для первого раза отличный результат. учитывая то, что всё делалось на глаз, на коленке. вот только как менять задние стойки? хотя, судя по видео с лодками, это пробный вариант. надо ждать продолжение. паренёк неугомонный, респект и уважуха!
I really like the way it came out, just be aware that running your wheels like that puts a lot more stress on your wheel bearings as well as some differences in handling.
@@nostreamavailable9090 or weld two rims together, have you seen the guy from russia building the cyper punk car, you should check that out its pretty cool.
The only thing I would have done extra is to spray the roof lining. Superb craftsmanship sir! It wouldn’t pass for registration in Australia with those tyres protruding though. 😱🙈😂👍🏻🙏🦘
love the work , love the ingenuity . But please anyone watching DO NOT copy this lug nut /spacer design for anything but slow off road use . Extremely dangerous and likely to fail at any moment . Anything over 20mph and this car will start to shake itself to pieces from those lug nut extensions .
great build....but... why leave on the rear door handles ? why not fill the shuts in ? the wheels are wrong on so many levels, turn them around. and the plant was still there ??
Bảo sao kênh toàn người nước ngoài coi. Người nước ngoài họ coi trọng nội dung sáng tạo, sự khéo léo trong kỹ thuật cơ khí làm ra những sản phẩm độc đáo đầy thú vị. Người xem Việt Nam hiện nay đa phần lại là phụ nữ và đám nhóc ác đam mê toàn thứ rác rưởi hèn chi nội dung của kênh này không được đề xuất nhiều! Respect you!Content creator good for life
Chuẩn bạn, nãy tui cũng xem kênh một ông kia cũng v, kênh Việt Nam luôn mà toàn người nước ngoài khen, mấy ông Việt Nam vô chửi xối xả, k hiểu kiểu gì. Đúng nhân tài ở VN k thể sống đc, ra nước ngoài mới phát triển đc @@
I think he cut too many corners here compared with his previous video where he restored an engine from the bottom of the ocean. Things he can work on are.. 1) restore the engine bay 2) install a back up light 3) roll out the fenders to cover the wheels 4) cover up the rear door handles 5) lift the front of the car 6) clean the suspension parts.
I've watched many of your videos over time. You are quite the talented craftsman & artist. I think it's time I subscribed. Thanks for all the great inspirational videos. Wish you the best from here in Canada.
Ok Mr. Ho this one is wild! Really Cool great job! LoL I'm so busy myself, I'm actually watching two of your shows right now at the same time trying to catch up😂🤣😂🤣😂 keep building my friend!
Still needs work, but much better than it was. Hose the bed down with bed liner. Remove the door handles and fill in the holes and seam. And for Pete's sake, finish cleaning up the interior. Glass and paint everything. Maybe even splurge on a layer of carbon fiber on the dash just for kicks.
Chỉ vì chở 1 cái chậu cây mà mất bao công sức và tâm huyết làm nên chiếc xe, khâm phục bác tự làm từ A-Z mọi công đoạn. Thuần thục các kỹ năng
I am just in awe of the skill this man has.. Eventho it’s not all flawless, he did convert and “rebuild” a whole car, just to be able to relocate his plant.. 😅 you have to be able to pull it all of in the end !! Awesome build❤❤
Você é muito inteligente 👏👏👏
Seus vídeos de conserto e restauração são ótimos e muito inspirador 👏
Excellent effort , using what you have , keeping cost down and very inexpensive , viewing from Detroit Michigan USA 🇺🇸 .
80系カローラ。もう30年以上前の車なのにきちんと整備すればまだ動く。というトヨタ車の耐久性の高さに加えてそれを配送車として活用してしまう動画作成者の手腕に感動しました。
テールが８６みたい
That reminds me of earlier in the 70s, when we welded rusty cars like this back together in Germany... but we had to go to the technical inspection with it... installing the rims the wrong way would have been an absolute absurdity... even though the colleague acted very brutally, but still he deserves a medal for welding with electrodes...all respect! 🥇🏆... we used acetylene and oxygen for welding, until the mig mag or the wire welders came up. he did a lot of work, disassembled everything... he could have worked a little nicer... but he's still a talent👌😎
amazing indeed :) well done
You are very polite. I respect the time Mr.Hô engaged into this conversion/restoration BUT it is not a proper work. In the mad Europe, the German TÜV would NEVER APPROVE this car. To me the worst about this car is the suppresion of structure bars in the trunks.
I've allways thought the german police was very strict about vehicle condition. This sounds like a sci-fi to me
@@alexandrhrouz666 Early in the 70's doesn't mean "today". Nowadays, it is not about the police but about the official check to allow your car on the roads.
@@alexandrhrouz666how did WV car pass the emission tests ? Lol
Welding sheet metal with a stick welder isn't easy.
It looks great, however, I am concerned about the rear shock towers not being strong enough.
How do you plan to get at the mounting nuts now that they are covered with fiberglass?
These builds are like Bic lighters, when it wears out you throw them away.
Angle grinder, inspection, more fibreglass... The whole build only took half an hour...! : )
У чувака есть плазменный резак, но нет полуавтомата?! 😂
He doesn't post often , but when he does you know something cool is gonna happen
Một trong những kênh CZcams đáng xem nhất Vn nhưng hầu hết khán giả đều là người nước ngoài vì sao? Vì nước ngoài thích tài năng khoa học kỹ thuật sáng tạo chứ không phải những cái vô bổ câu like câu view
Vì người nước ngoại ko có thợ lặt vặt như vn.
Bên mỹ làm gì cũng phải có bằng.
Ko như VN.
Lên họ ko biết sửa chữa lên thíc xem video này.
Vn thì đầy việc bạn thíc học sửa chữa oto miễn phí cũng có
Ijlv9087😊😊😅😮😮😮😢😢0😢😢😮😅😊
4ty ff 😮😅
Kjjk7980
❤is 🎉❤🎉6 😢ri
1) как заменить в случае дтп задние фонари
2) как заменить в случае неисправности задние стойки
3) ручку задней двери можно было заварить, и зашпаклевать
4) зазоры на задней двери можно было сделать тоже самое что и с ручками
5) развернуть колеса и установить странное решение
Есть много недочетов я так понимаю авто было сделанно только для контента. Но многие и такое не смогут сделать.
Зделано на отьебись,таким мастерством многие азиаты в ютубе страдают ,вечно по верх ржавчины красят
Согласен полностью, хотя бы разварки сделал, а не это убожество, видос чисто просмотры срубить
Он сделал для себя и как ему захотелось + на коленке грубо говоря. У него хотя бы инструмента дофига@@lexdrive3127
Ещё и внутри арок дыры от коррозии оставил сквозные😁
Muy lindo su corollita el que tiene un Toyota sabe lo que tiene desde costa rica 🇨🇷 saludos amigo
คุณเก่งมากๆซ่อมเป็นทุกอย่าง👏👏
#จากไทยแลนด์
Beautiful work on the car transform into pickup.
As always, your work is nothing short of amazing. You put a great deal of hands on engineering into your work, and the level of ability & knowledge is simply priceless.
I was hoping the rear doors would have been sealed up to look like a factory ute also, but if it was intended to identify a modified sedan, then i get it 😁well done bro, fantastic job.
Here in Australia, unfortunately, it would never pass an engineers modification certificate. There is a big list of structural compliance and requirements that must be met before they even look at the project. But who cares, You're not in Australia 😂
Yeah, fuck the gov regulators. Health and safety? They can kiss my ass.
Good job Mr ho I weld and fabricate trailers myself and I much appreciate how you do your videos all the process at once as compared to seeing months worth of videos in real time it is better for me to see the entire process in a timelapse version
Bạn rất giỏi và sáng tạo! Tôi bái phục bạn!!!
This is pretty amazing. And I say this as someone who worked around body shops selling PB&E for years. I've seen a few conversions of this type done, and the only thing I can say that I would do differently would be a little stronger material at the top of the rear shock/strut towers and a heavier box system to tie the two upper rear towers together (probably a u shaped box to go under the rear window, with a couple of pillars down to the floor "frame"). Without it, I see some flex issues on the body/chassis, but overall it's amazing.
I see some rust I would have cut out replaced as well to make it structurally stronger, but overall, I get the "where do I stop" question on an old beater like this...
Also, MAD PROPS for using the stick welder on your sheet metal!
In places like Asia no one there has much money but they have sometime some tools and are afraid to take on job like this
Great job, terrific idea Mr. HO! Thanks for taking the time to make a video of your creation.
This is amazing! For using what you have you really transformed that 4 door Toyota into something that reminds me of a Subaru Brat. 👏
Очень похоже 😂
I was thinking the same as soon as he pulled that rear window forward and started attaching it.
Mr HỒ Thánh Chế this super crazy but as well super cool!! Great job as always!!
you should have welded the backdoors and make them disapear, would look much better...
I was just about to say the same thing and he should not have put the wheels that way he's lost half of his turning radius
Disaper 😎
Good
Bro there is some cabin 💭
I agree. Welded the door seams. And shaved the handles.
1984 Corolla SE. my first car in 1994. Man the memories.
Nice idea 👍
Shame the rear towers didn't get reinforced, and then get completely covered with fibreglass!
Lots of issues, with body, suspension, steering, even those rear lights are half done...
Nice idea, just a bit rushed.
Don’t you recognize that all tool and equipment he have is : grinder , welder , antique hammer , and some very basis tool ? The point is he did an amazing job with what ever he has on hand which nothing .
I'd use the trunk lid and the piece of the roof to make a removable tonneau cover for the new bed.
also since the bed seems to be water tight you might want to drill one or two small drain holes at the lowest end of it for rain and any spills.
Well done and thank you for sharing! 😀 Mark from Australia!
Very Goody!! Sao paulo Brazil!!
Very cool build, you have some severe dedication. Great job!
Is there anything this guy can't do? Really admire your ingenuity.
Decent welds
يا ايها الذين آمنو لا تلهكم اموالكم ولا اولادكم عن ذكر الله ومن يفعل ذالك فاولئك هم الخاسرون......
سبحان الله وبحمده سبحان الله العظيم. الباقيات الصالحات وللذكر الله اكبر.......
not downing him in this video and (Imm not good at that stuff ) but the door handsfor the back and the back door outline i would of try to bondo all of it where it look more cooler like it was really made like that but thats cool little truck
Someone please send this man a welding helmet!
I'll try to contact him.
And a proper paint mask xD
@TyBraek, he also needs welding gloves.
Mr Ho deserves his own show on Motor Trend TV.
@@pauldrusch1805 today on motor trend tv Vietnam edition Ho here is gonna turn this clapped out 88 corolla into a pickup truck.
I appreciate the time to retrofit this vehicle and make the video. Yes there are things I would do differently, but well done, keep improving. Blessings from the Caribbean.
Very good mate 👍
In Australia we call that car type a ute and it's common here, like a mini truck
This is basically a brumby
@@tbagindustries4331 yeah totally 👍
Check out Merlin’s Old School Garage channel. He took a Volkswagen Jetta and made a ute. He used a kit. It’s pretty interesting. Here in the states, we don’t see that much. However, I would drive one. Cool looking trucks….
I like the conversion a lot! Excellent planning, but I see that the turning is going to be an issue. Also the rear door handles and door gaps could have been filled at one point to where it would look like a factory offering.
I thought the very same thing. Also he did not make any provisions for drain holes for the bed in the event of rain...
yeh i would have welded them up
@@franksanta-teresa971 also how does he adjust the rear shocks because it appears he fiberglassed over them, they should be covered but made a removable cover for repair
NO D.O.T (Department Of Transportation) regulations we love 3th World Countries.. Just paying for tags once..free rides for ever.. ahhhhhh.. Much love from USA United States of America ahhhhhh
I like the fact he left the handles and gaps! if he filled them in, who would have looked twice thinking its just another mini truck..
Tôi rất phục em .Em rất giỏi.
Looks great except for the wheels. You have to turn them back around or get new ones.
Yeah, not much turning radius with the tires hitting the fenders?
Lột cái sàn ra nhìn chán luôn, nhưng bác vẫn làm từng tí một, thật nể quá! Không phải nể vì kỹ năng mà nể nhất là sự kiên nhẫn vô cùng! Respect!
You made the BEST version that car has ever seen. AMAZINGLY practical and badass.
You, sir, are an absolute inspiration. Please keep doing whatever it is you are doing!
Талантливый человек! Хорошая прокачка 🎉
Прикольный пепелац получился, по дешману пойдёт. Но я бы заварил задние двери, убрал бы задние внутренние арки заменив пружины на торсионы, тогда бы и погрузочный объем бы увеличился. Заменил обычный ручник на электро ручник, тогда бы можно было поставить задний диван в салон вместо двух седений. Для мультимедиа сделал бы подиум и перенёс бы наверх вместо часов.
@@contactmeonnicegramdiybyja2278 what is it nisegram?
Excelente trabajo . Saludos desde Apodaca Nuevo Leon Mexico.
Bonjour, super ce projet, amities de Narbonne 👍🏻
I didn't want one of these until now. Go Mr. Ho!
If you had the hatch 4 door, or the tailgate from a Corolla FX, you could make a gate to extend the bed into the passenger compartment for larger items. My family had an 84 Corolla back when it was brand new. I had an 88 FX AE88.
Bạn giỏi quá bạn ơi
Quá tuyệt vời!!! Mong 1 siêu phẩm khi bạn kết hợp du thuyền dưới nước và đi được trên bộ!!! 🤝♥️☕️☕️☕️
Awesome!! Love seeing stuff like this and your really the only one I've seen doing it. Maybe you should update along the way? Just do extra stuff to it and post videos. I know me and a lot of others would love to see it. But great jib man!! I'd drive it and use it all the time !!
I like it alot man your work is amazing! If i might suggest weld that door full so there is no more door line, and remove handel and also make it smooth. That way it would look more like one panel. Its only my personal opinion, but like i said man great work!
Greetings from Barcelona Spain. Good videos.
Absolutely gorgeous and super practical, I truly am impressed.
Thank you for posting this great job!
Fantastic transformation and effort :) I just would have added some tie-down points in the back to secure loads safely. Also a drain hole somewhere with all the rain you get :)
My grandpa did basically the same thing to an old four-door sedan he had years ago when I was a kid. The main difference is he left the back doors where they opened. That way he could load stuff from the side without lifting it over if he had to.
Smart man
Photos would be cool,
There was a guy in Virginia who did this to a Cadillac.
Fantastic! I actually want to do that same thing with my car! All you need to add to it now is a simple cargo net tailgate!
Toyota c'est fantastique !!👍 Encore plus 30 ans a rouler 👏👏👏
I LIKE it!!!!!!👍👍👍👍👍
Пару вопросов: зачем такой большой вылет колес, и, было бы неплохо дренажное отверстие в кузове на случай дождя. А вообще Супер! Успехов!
А ещё не мешало бы зачистить ржавые места
Тачка металлолом, побыстрому решил продлить ей жизнь не на долго и просмотров срубить за одно, с их влажным климатом она за 5 лет в труху рассыпется после такого "ремонта".
Аплодирую стоя! Красавчик!🎉🎉🎉уникальный молодой человек, знает авто как пять пальцев, от электрики до кузовщины.
Но делает ×уйню
Quá tuyệt vời bác ạ!!!
Like it, effort well rewarded
Damn, your creations are always magical, a joy to watch!
Việt nam mình có quá nhiều nhân tài…..
Quá ngưỡng mộ anh quá giỏi❤❤❤
Cai gì cũng lam dc
Ilke very good VDO 🙏🤠💞 happy New year ♥️♥️♥️
Gorgeous! Really enjoyed the yellow color. Even though the black and white "dream" at the beginning showed the design, that yellow was a beautiful surprise when you started painting!
The biggest achievement in my mind is taking all of that apart, especially the dash, and putting it back together.
для первого раза отличный результат. учитывая то, что всё делалось на глаз, на коленке. вот только как менять задние стойки?
хотя, судя по видео с лодками, это пробный вариант. надо ждать продолжение. паренёк неугомонный, респект и уважуха!
Он какой отморозок, просто в шоке с него😂
Absolutely stunning. Super welding skill.
Rất hy ay chúc sức khỏe nhé bạn
Good job ! 👍
I really like the way it came out, just be aware that running your wheels like that puts a lot more stress on your wheel bearings as well as some differences in handling.
A LOT more i'd say. still, it should work, esp if its not daily driver on long distances ;)
He should widen the front wheel wells so he doesn't have the tires stop when turning
I wonder if he could lengthen the wheel studs and run twin rears like a dually?
Looks a bit like a Subaru brat with that raked stance
Very cool 😎👍
@@nostreamavailable9090 or weld two rims together, have you seen the guy from russia building the cyper punk car, you should check that out its pretty cool.
I am impressed, I did almost the same thing with a 1966 Ford Mustang but it was a two door and almost easier to do because of that.
Quá đỉnh giỏi đẹp Anh
The only thing I would have done extra is to spray the roof lining. Superb craftsmanship sir! It wouldn’t pass for registration in Australia with those tyres protruding though. 😱🙈😂👍🏻🙏🦘
I am a little worried for the rot and the rear coil mounts, but seeing as they are fiberglassed over, it may be fine for a while
until you want to replace those struts
That is a1985 Toyota, had one new in 1985 nice to see it lasted this long! Nice job!
quá trời đỉnh luôn, am hiểu và khéo tay thật sự
I don’t always agree with every aspect of your designs, but there is no denying your skill and attention to detail. Good work, good video!
يا ايها الذين آمنو لا تلهكم اموالكم ولا اولادكم عن ذكر الله ومن يفعل ذالك فاولئك هم الخاسرون......
سبحان الله وبحمده سبحان الله العظيم. الباقيات الصالحات وللذكر الله اكبر.......
Should have removed the rear door handles and filled it in as well as the space around the rear door and it would be perfect :)
love the work , love the ingenuity . But please anyone watching DO NOT copy this lug nut /spacer design for anything but slow off road use . Extremely dangerous and likely to fail at any moment . Anything over 20mph and this car will start to shake itself to pieces from those lug nut extensions .
great build....but...
why leave on the rear door handles ?
why not fill the shuts in ?
the wheels are wrong on so many levels, turn them around.
and the plant was still there ??
"Mom, can we have a Hilux?"
'We have a Hilux at home..."
Well done, Mr. Ho.
Bảo sao kênh toàn người nước ngoài coi. Người nước ngoài họ coi trọng nội dung sáng tạo, sự khéo léo trong kỹ thuật cơ khí làm ra những sản phẩm độc đáo đầy thú vị. Người xem Việt Nam hiện nay đa phần lại là phụ nữ và đám nhóc ác đam mê toàn thứ rác rưởi hèn chi nội dung của kênh này không được đề xuất nhiều! Respect you!Content creator good for life
Chúng tôi đánh giá rất cao! Cảm ơn bạn!
Chuẩn bạn, nãy tui cũng xem kênh một ông kia cũng v, kênh Việt Nam luôn mà toàn người nước ngoài khen, mấy ông Việt Nam vô chửi xối xả, k hiểu kiểu gì. Đúng nhân tài ở VN k thể sống đc, ra nước ngoài mới phát triển đc @@
Fantastic job. Please continue to give us transformations like this one...
عمل جيد انا اشجعك👍
I think he cut too many corners here compared with his previous video where he restored an engine from the bottom of the ocean.
Things he can work on are..
1) restore the engine bay
2) install a back up light
3) roll out the fenders to cover the wheels
4) cover up the rear door handles
5) lift the front of the car
6) clean the suspension parts.
Thấy bạn💪🇷🇺
Beautiful job. Ver6 good
Nice job !!! 👍
In Italy isn’t possible bild or modify a car easily like this...there’re a lot of burocratic problem... 😡
Chỉ tiếc VN ko cho đăng kiểm ^^ chứ rất đẹp
Ông này càng ngày càng hay... thích đoạn đầu video ghê kkkk mãi ủng hộ nha❤
I've watched many of your videos over time. You are quite the talented craftsman & artist. I think it's time I subscribed. Thanks for all the great inspirational videos. Wish you the best from here in Canada.
Ok Mr. Ho this one is wild! Really Cool great job! LoL I'm so busy myself, I'm actually watching two of your shows right now at the same time trying to catch up😂🤣😂🤣😂 keep building my friend!
Tuyệt vời! Kỷ năng và sự kiên nhẫn
Muy buen trabajo amigo,excelente
Đúng là quá Đam mê. Vừa tốn tiền lại mất công. Nhưng lại không thể tham gia giao thông được.
Nice transformation car to pickup. Well done.
Flared wheel arches, excellent build.
Still needs work, but much better than it was. Hose the bed down with bed liner. Remove the door handles and fill in the holes and seam. And for Pete's sake, finish cleaning up the interior. Glass and paint everything. Maybe even splurge on a layer of carbon fiber on the dash just for kicks.
quá khâm phục tài năng
em nghĩ anh bỏ tất cả máy móc ra rửa sạch sẽ và sơn lại cả máy móc bị rỉ sét bên trong thì video này sẽ hay hơn ạ
My first car in 1995 was a 1985 Toyota Corolla Seca 5 speed manual 1.6 L petrol hatchback. My second car was a ute.
Dọn lại quá chất .Đi đăng kiểm luôn Hồ.