@@novicelumberjack I brought down the lowers on mine last year for saw fest. Lost a bit of torque unfortunately, but still had the grunt to place second. That mod doesn’t always work I’ve noticed. Maybe if I knew what I was doing it would🤔
Impressive for what was done👍🏻 in some cases, piston work definitely pays off! I've only ported about a dozen saws but have only fully polished to a nearly mirror shine 2 exhaust ports. Typically call it good after 800 grit or scotchbrite on a split mandrel.
Hard to beat some good Ole machine work. I think you move the transfers up a few degrees, a muffler mod, and a slight timing advance, you'll have a screamer.
I'm so glad i became a Lumber Hack/member!! The extra membership content is sooo worth every penny! 🧟♀️aahh Need more Captain Chainsaw aahh aahh more aahh!!😊
Can’t go wrong with those rough timing duration’s… I don’t ever really cut out my torque and I’ve found those Hyway aftermarket coils from hls almost always help my performance so I just immediately start there anymore…. Dragging down those lowers in the 660’z to help that fuel charge get to the uppers…. Just good solid fun anytime you are playing around and trying to get a little bit more out of a chip ripper!!! Keep kicking butt, dude!!!
Ye man I'm looking forward to this! Not only upper Transfers need raising but I think the Intake duration may be a little short too... Maybe 78 to 80 is ideal.... But hey... You can raise the uppers and test and then maybe lower Intake and test to see what's what! While all still maintaining over 40 degrees case compression..... Keep it up dude love these vids!
@@novicelumberjackI build two of the 660 kits and the cylinder s were Int 82 amd ex 96 stock... So I didn't move them just widened the exhaust.... I have one with tramsfers at 119 and the other with Transfers at 115. This if course leaves me with only 37 and 33 degrees case. Comp respectively so since case comp is low I compensated by running really open Exhaust so the back pressure doesn't combat the case charge through the Transfers. I feel that is future builds if I can get the machine work done, I will drop the jug to get Ex to 98 or 99 and jb the Intake back up to 78/79 Keep in mind the 660 Ex port width is limited because of the Piston pin locations so I think that's why these saws tend to like a higher Ex roof so they can breath. Mine run awesome at 96 roof but I Havnt cut big wood.... So torque may be lacking.... Anyhow looking forward to whatever you do!
Hey I don't know where you're getting your information at but they're dead wrong because who Savannah is not ending their gas chainsaw lineup they just come out with a new one
Lookin' good my friend. Welcome back. Enjoyed the vlog on the trip to Japan.
Hey RF
👍🆙RF
I've checked out his stuff on ebay. Just never pulled the trigger. I may give em a shot. I like the look of the 372 spikes 👍🏻 great build tho buddy.
Hey BP, Coming along nice!
These 660 clones are great, good one big dog👍🏻
Yep, really liking this thing. Still a lot of other things to do to it though. Hopefully I'll be able to get a good bit more power out of it still.
@@novicelumberjack I brought down the lowers on mine last year for saw fest. Lost a bit of torque unfortunately, but still had the grunt to place second. That mod doesn’t always work I’ve noticed. Maybe if I knew what I was doing it would🤔
Good gain!!
Impressive for what was done👍🏻 in some cases, piston work definitely pays off!
I've only ported about a dozen saws but have only fully polished to a nearly mirror shine 2 exhaust ports. Typically call it good after 800 grit or scotchbrite on a split mandrel.
Hard to beat some good Ole machine work. I think you move the transfers up a few degrees, a muffler mod, and a slight timing advance, you'll have a screamer.
🙋♀️T-Dubb
I'm so glad i became a Lumber Hack/member!! The extra membership content is sooo worth every penny! 🧟♀️aahh Need more Captain Chainsaw aahh aahh more aahh!!😊
HOOOOO
Holy smokes you are really pumping content for members👍
Yes I am. And if they don't like it... well, you know.
@@novicelumberjack 😁
Good stuff!👍👍
looking forward to this
Glad to hear it!
👍👍running good!
Thanks, Doug!
👍🆙CF
🙋♀️CF
Can’t go wrong with those rough timing duration’s… I don’t ever really cut out my torque and I’ve found those Hyway aftermarket coils from hls almost always help my performance so I just immediately start there anymore…. Dragging down those lowers in the 660’z to help that fuel charge get to the uppers…. Just good solid fun anytime you are playing around and trying to get a little bit more out of a chip ripper!!! Keep kicking butt, dude!!!
Thanks Dave. Always appreciate your thoughts!
Ye man I'm looking forward to this! Not only upper Transfers need raising but I think the Intake duration may be a little short too... Maybe 78 to 80 is ideal.... But hey... You can raise the uppers and test and then maybe lower Intake and test to see what's what! While all still maintaining over 40 degrees case compression..... Keep it up dude love these vids!
Thanks man. Yeah, still quite a bit of playing around left to do. It's a fun saw to work on.
@@novicelumberjackI build two of the 660 kits and the cylinder s were Int 82 amd ex 96 stock... So I didn't move them just widened the exhaust.... I have one with tramsfers at 119 and the other with Transfers at 115. This if course leaves me with only 37 and 33 degrees case. Comp respectively so since case comp is low I compensated by running really open Exhaust so the back pressure doesn't combat the case charge through the Transfers. I feel that is future builds if I can get the machine work done, I will drop the jug to get Ex to 98 or 99 and jb the Intake back up to 78/79
Keep in mind the 660 Ex port width is limited because of the Piston pin locations so I think that's why these saws tend to like a higher Ex roof so they can breath. Mine run awesome at 96 roof but I Havnt cut big wood.... So torque may be lacking.... Anyhow looking forward to whatever you do!
Stock carburetor or did you swap out for the Tillotson?
That's actually still the stock Chinese carb. It's really running great considering what little I have done to it.
Have you ever done cedar wood with these chain saws
If you want more rpm, advance the timing some more and shorten you blowdown a bit. They can usually be advanced quite a bit in my experience.
🙋♀️Boedy
👍🆙AW
Comment from me today
Thanks Coolguy
👍
👍🆙BigGuy
What's up Doc!
@@novicelumberjack Hellooo & HOOOOO!😁
@@novicelumberjack enjoying some cooler weather finally, time 2 start working on some stuff!
Hey Doc, Hoooo...!
@@TightWad1 Hello, TightWad!
Yeah Husqvarna is not changing their lineup they just come out the new line of gas chainsaws this year
Hey I don't know where you're getting your information at but they're dead wrong because who Savannah is not ending their gas chainsaw lineup they just come out with a new one
Comments helps the youtubes!!!!
Bring it on Boedy if you can build that Chinese chainsaw to hang with Ike Turner and Boby Booshay you can say you did something special!!!
I'm thinking I can do it. But we'll see. Both those saws run soooo well.
Try a timing advance, n muffler mod before you go back into it 🤷🏼♂️