MR Configurator2: How to Install, Read & Write parameters MR-J4 Servo Amplifier - P14 | MELSERVO-J4
Vložit
- čas přidán 6. 09. 2020
- Video này mình hướng dẫn cài đặt phần mềm MR Configurator2.
Phần mềm MR Configurator2 được dùng để cài đặt thông số, điều chỉnh, bảo trì, kiểm tra lỗi, đọc và ghi thông số,... của Servo Amplifier Mitsubishi.
In this video, I instruct to install MR Configurator2 software.
MR Configurator2 software is used for parameter setting, adjustment, maintenance, error checking, parameter reading and writing, ... of Mitsubishi Servo Amplifier.
Automation | Mitsubishi
1. GX Works2 : Installation & Simulator - P1 I Cài đặt và chạy mô phỏng PLC Mitsubishi 👇
• GX Works2 : Installati...
2. How to install GT Designer3, HMI Mitsubishi - P2 | Cài đặt phần mềm lập trình HMI Mitsubishi 👇
• How to install GT Desi...
3. How to Upload & Download program Mitsubishi FX3U PLC by GX Works2 - P3 | Upload và Download PLC FX 👇
• GX Works2: How to Uplo...
4. GT Designer3: Upload and Download program HMI GOT2000 by USB cable - P4 👇
• GT Designer3: Upload a...
5. GT Designer3: Upload and Download program HMI GOT2000 by Ethernet cable - P5 👇
• GT Designer3: Upload a...
6. GX Works2: Upload & Download program Mitsubishi PLC MELSEC-Q Series by ethernet cable - P6 👇
• GX Works2: Upload & Do...
7. How to connect GOT2000 HMI with MELSEC-F Series PLC - P7 . Tạo kết nối HMI Mitsubishi với PLC FX 👇
• How to connect GOT2000...
8. How to Upload, Download and Monitor the PLC program via GOT - P8 | Download chương trình PLC qua HMI 👇
• Upload, Download and M...
9. GX Works3: Installation & Simulator - P9 I Cài đặt và chạy mô phỏng PLC Mitsubishi 👇
• GX Works3: Installatio...
10. How to simulate GT Designer3 with GX Works2 - P10 | Kết nối GT Designer3 với GX Works2 qua mô phỏng 👇
• How to simulate GT Des...
11. GX Works2: How to connect KEPServerEX with MELSEC-Q Series by ethernet driver - P11 👇
• GX Works2: How to conn...
12. FX3U PLC: Communication Modbus RTU with E5CC Temperature Controller - P12 | Truyền thông Modbus RTU 👇
• FX3U PLC: Communicatio...
13. How to connect WEINVIEW HMI with FX3U PLC - P13 | Tạo kết nối HMI WEINTEK với PLC FX 👇
• How to connect WEINVIE...
14. MR Configurator2: How to Install, Read & Write parameters Servo Amplifier - P14 | MELSERVO-J4 👇
• MR Configurator2: How ...
Các bạn nhớ ủng hộ mình bằng cách nhấn Like và đăng ký kênh mình nha.
Nếu có yêu cầu gì thì comment bên dưới giúp mình .
Remember to support me by clicking Like and Subscribe to my channel.
If you have any questions, please comment below.
#ThuanAutomation
Thank You & Best Regard !!!
***********************************
☆ FOLLOW " Thuan Automation "
▶ Email : thuan.automation3003@gmail.com
▶ Phone : +84 931359303
▶ Subscribe : bit.ly/2RKbVD3
▶ Facebook : / thuanautomatic
▶ Zalo : zaloapp.com/qr/p/hjzjeafqnsei
***********************************
© Bản Quyền Thuộc Về Kênh Thuan Automation
© Copyright by Thuan Automation Channel
⛔️ Do not Reup - Věda a technologie
Phần mềm MR Configurator2 được dùng để cài đặt thông số, điều chỉnh, bảo trì, kiểm tra lỗi, đọc và ghi thông số,...
MR Configurator2 software is used for Setup,Tuning, Maintenance, Alarm display, reading and writing parameters, ...
Thanks you so much
A Thuận cho e hỏi, Driver J4-b e dùng qdmh4 khai báo thành j3-b, bây giờ e muốn phục hồi thành j4 thì làm thế nào ạ ?
@@thanhbinh7687 nó kêu chỗ motor hay driver
@@ThuanAutomation motor kêu a ạ, a có thể giúp e được không
@@thanhbinh7687 đem ra tiệm sửa
Cám ơn anh đã chia sẽ kiến thức của mình cho mọi người
hướng dẫn của anh rất hay cho ai quan tâm phần mềm này
Cảm ơn em
Cảm ơn bạn đã chia sẻ cài phần mềm rất hay chúc bạn thành công
Cảm ơn bạn nha
Bạn cho mình hỏi điều khiển vị trí.toi vì trí đó nó dùng.nhung sau đó nó dịch thêm 1 đoàn nhỏ nữa.la cái đặt như thế nào vậy bạn?
I have similar error with u sir, there is alarm 20.3 about communication encoder. What should I do if occur that alarm sir?thanks!
Hello Thuan thank you for your knowleldge
Can you please make a video just for errors codes and how to solve them ?
Ok you
Anh cho Em xin link tải phần mềm phiên bản này có được không ạ? Em cảm ơn
Anh cho xin đường link tải phần mềm này được không ạ?
anh ơi cho em xin link tải app với ạ
Chào anh, anh cho e hỏi: servo khi dừng thỉnh thoảng nó bị kêu hú chói tai, khắc phục hiện tượng đó như thế nào ạ ?
Motor kêu hay driver kêu em
@@ThuanAutomation motor kêu a ạ, a có thể giúp e được không
cho em xin link tải với được không ạ
i download program from MR-JE-40A servo. but the project is read only. axis writing option is disabled here( faded)
how to enble this option?
You created new project or upload parameter from servo then download
@@ThuanAutomation my problem was pc was not connected with servo. when i connected through usb then the axis writing button enbled
@@techideas6876 you open the device manager, check accept usb driver ?
Cho em xin link với ạ
The mrj3usbcb3m usb data cable is the same as the usb cable on the market
Ok you.
@@ThuanAutomation that same or not?
Thầy ơi cho em xin link tải MR confirator2 ạ
Em check mail
Bạn cho hỏi sevor báo lỗi 16:3 phải làm thế nào
Servo hãng nào, model là gì bạn
@@ThuanAutomation melsevor J4 của misu
@@vanhieungo9822 gửi model cụ thể nó có nhiều dòng A,B,..
@@ThuanAutomation e kiểm tra dây không sao vậy nó hỏng ở đoạn nào a
@@vanhieungo9822 anh hỏi model của em là gì
anh ơi, anh cho e xin link tải với ạ
Ok em
buenas... alguien que tenga el instalador del programa por favor.........
what ?
me imagino que ya lo encontraste porque hay mucho de donde descargar, buscas versiones mas antiguas las cuales son mas faciles de encontrar e instalar en modo full