Super Bass Stereo audio Amplifier using PAM8403 | pam8403 5v amplifier bass
Vložit
- čas přidán 24. 07. 2024
- DIY Super Powerful Stereo audio Amplifier using PAM8403 | pam8403 audio Amplifier
Super Powerful Stereo Bass Amplifier with PAM8403 module
Can the output power of the sound amplifier be increased?
In this video I show how to use the pam8403 module and how to amplify its output and build a 5 volt audio system for our car.
-------------------------------------------------------------
Click on the link to see more videos on this topic:
/ @skillmake
---------------------------------------------------------------
The PAM8403 is a 3W, class-D audio amplifier. It offers low THD+N, allowing it to achieve high-quality sound reproduction. The new filterless architecture allows the device to drive the speaker directly, requiring no low-pass output filters, thus saving system cost and PCB area.
Image result for pam8403
------------------------------
Track: Naron - Imagination [NCN Release]
Music provided by NoCopyrightNation
Watch: • Naron - Imagination (I...
Stream/Download: ncn.ffm.to/naron-imagination
-------------------------------
About This Video -:
PAM8403
5 volt amplifier
mini amplifier super bass
how to make amplifier at home
powerful bass audio amplifier
how to make amplifier at home
how to make amplifier
___________________
00:00 pam8403 5v amplifier
07:00 audio Amplifier using PAM8403
#pam8403 #amplifier #superbass #ampli #audioamplifier #PowerfulStereoBass #skillmake
#miniamp #5vamplifire - Věda a technologie
♥️❤️❤️
thanks for comment 🙏🙏🙏 .mr??
@@skillmake 🥰🥰🥰😘
ഇങ്ങനെ connect ചെയ്യാമോ? അടിച്ചുപോകില്ലെ?
these amps are already 4 ohm stable and youre running 8 of them into approximately a 1 ohm load, so each is probably seeing the equivalent load of an 8 ohm load. also youd get more power running them at their rated 5v instead of 3.7 or under load likely closer to 3v. also assuming they were all making their peak rated power you would be getting less than a typical car audio head unit.
no crossovers on the speakers and those smaller speakers and tweeter would be working very hard getting the full frequency spectrum........Also each amp does not have any protection on its output thus some of the amps will be working harder then the others normally when you see multiple fets or amps you use a resistor to load balance. Oh well it was good for a laugh.
each 1 of those little amplifier boards dont push out more than 3W at 5V. they are rated for 5W but they dont do more than 3W at 5V
Red wire basically use for right channel of audio applications
Ini yg kucari.. benar2 meningkatkan daya ..
bukan pakai modif tone control pasif yg hanya mengurangi/menghilangkan suara midhigh nya ..
Kerennn..
Жесть, невероятно, дайте автору премию за гениальность 😁😁😁😁
😂😂
Оскар за гениальность... А может 10 оскаров?
А лучше столько Оскаров - сколько Он плат запараллелил. 😁😁😁😁
@@TheKamarataboba самое интересное что мощность как у одной микрухи по итогу все равно на выходе
@@g-forsemanx4664 и далеко не факт, что все усилки заработали, они ведь D класса и на выходе дросселя нет, фиг знает что с генерацией там происходит, уверен, что синхронно они не запускались
We almost can see the impedance say hello to those speakers... if you going to try this at home, please read about it...it save you a lot of trouble and a bit of money. Btw...you just need one AMP... not 8. Good video tho.
What is the key difference between 1 pam8403 vs 8 stacked pam8403
Does the power is increased sightly?
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 czcams.com/channels/BoZGn08nBAxE9M5T53_UKg.html
@@utkarshchari7931 It depends on the Supply Power and Impedance of the speaker
[ I = V/R ] If your speaker type is 4ohm and your supply voltage is 5v then.
[ 5 divided by 4 = 1.25A ] which means
[ 5 x 1.25 = 6.25watts ] 1 amp of current 6W runs to the Speaker.
Ex 2
If your speaker is 8ohm and your Supply voltage is 24v then.
[ 24V / 8ohm = *3A* ]
[ 24V x 3A = *72Watts* ]
Ex 3
So if you want 1,000Watts 24Volts runs to your Speaker Coil and 4ohms speaker Impedance then.
[ Watts / Voltage = Current ]
[ 1000w / 24v = *41 Amps* ]
Hope this helps to find a suitable speaker and amplifier and also power Supply DC to DC or AC to DC Supply Thanks for reading :)
@@ReimuReimu_Animation very well explained. ..
So is there any point of stacking 8 5v amps over just 1 amp?
They all get 5v 1A 4 Ohm anyway
@@arielbene2013 yep it depends on the speaker ohm if it's 1 ohm then it's like a short circuit it will suck more current than 4ohm
It's not fake it may possible but you need 5 volt 10amps adapter
Hello dear friend, yes, you are right, it has a high amperage
@@skillmake if speaker has 4ohm resistance , then max current will be 1.25 x 2 = 2.5 amp, and current cannot go beyond that. simply its fake
@@lovneetsingh6664 what if he use a lipo battery that can supply a lot of current thought 🤔
@@Roriloty even if using lipo battery, the max current will be 2.5A. 5V cannot give more than 1.25A per channel. Simple ohms law I = V/R
@@lovneetsingh6664 what if I connect multiple batteries in series would it work? (And thick wire)
8 stacked together and still barely enough to push a 20 watt speaker. Super Powerful!
i highly doupt that the 8 amps could drive the two 300W speakers. at 5V the current supplied by the batterys would neet to be 120A . even if that were possible it would let those puny wires and speakers go up in flames imeadietly.
Correct! This video is complete BS!! Super powerful my ass! :( I was doing an audio engineering course where the main amps we used were QSC and Crown 2400W RMS bridged into JBL SRX825s. Even that wasn't "super powerful". It's really just industry standard. Those 300W speakers are also bullocks. The way ratings are applied to car audio, you'll find they're around 25W RMS. Good video for comedic value I guess.....
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 czcams.com/channels/BoZGn08nBAxE9M5T53_UKg.html
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 czcams.com/channels/BoZGn08nBAxE9M5T53_UKg.html
@@maximilianjuli4895
So what do you think this is fake
I m going to try it and i thinks a lot about it what if this isn't work
Please guide me bro
Я извиняюсь, но это что за херня ?! Паралелить усилки да еще в таком количестве?! А резисторы с плюс питания на входы зачем?! что б помехи по питанию слушать?! Срочно отдать на проверку Доктору)))
it just for test 🙏👌
Да это пиздец. Ещё нагромождение спикеров, разной мощности, разного сопротивления, все параллельно. Кажется, чела в школе научили только ПАРРАЛЕЛЯМ. Странно, что он не присоединил несколько входов и к ним несколько телефонов с одной мелодией не запускал параллельно
Хаха ещё этот долбан думает, что там у него выдало почти 50W.Это наверное, какие то параллельные ватты, из параллельного мира
that's insane but awesome. great video.
Great innovation... Keep it up 👍. love you from India 🇮🇳 proudly..
Thanks mr Kumar thanks for watching
Sir
I appreciate your talent.
Thanks for paying it forward by sharing.
Also I love channels who interact with the comment section. Your light shines bright even through these digital boxes we find ourselves trapped in from time to time.
God Bless.
thanks 🙏🙏🙏 mr jailbreak?
He has no talent...
मेरा भारत महान। जब तक आप जैसे नागरिक हमारे भारत ने है। कोई चाइना हमसे आगे बेहतर नही हो सकता। 👍
नमस्कार प्रिय मित्र, मुझे बहुत खेद है, अमल, मैं ईरान से हूँ, लेकिन मुझे आप जैसे भारत के दोस्त बहुत पसंद हैं 🙏🙏🙏
@@skillmake मुझे वह सभी लोग प्रिये है जो सभी की सहायता और एक दुसरे की सहायता करते है बिना किसी स्वार्थ के मुझे किसी भी धर्म, पंथ, मज़हब , रिलीज़न और देश से कोई लगाव नही बस अच्छे और सच्चे लोग मिलने चहिते। ॐ
@@shivsaini3562 ngomong apa sih
Yo Wanna be indian. Memory of arians is coming backto us....soon end of trials and tribulations. Replacement hoomans time is ending. I was always blown away that as a polish lad i was preaching vedic teachings to wanna be indians who should understandit deeper than me...or do they ? Truth is coming to the surface. What's then. Are you panicking ? Cuz im excited.
And that moon landing done in a style of power rangers from 90s 😂
nice job...how about another PAM's module?, have you got experience too?
I think it is the same in other modules👌👌
Keren ... mantap .... kreatifitas tiada batas.... Salam kenal dari Lereng Gunung Slamet saudaraku
🙏🙏🙏
2 таких слабых аккумулятора не подходят для этого, их не хватает. 1 аккумулятор 18650 намного лучше подходит так как он сможет выдать 10 ампер спокойно
👌👌
Congratulations from the bottom of my heart I do a good job for you
Please help me write down the ICs I need to fix this
🙏🙏🙏
Bro im using 3 pam 8043 amplifiers combined with mp3 bluetooth module and im using these amplifier with 25w speakers in pairs for one pam board but when heavy bass comes the voltage drops so can you 3 me a powerfull power supply to the boards.
what value r those rwsistor and filter cap u put on Input leads ?
Details of all items are written below the video Dear friend
gracias por el aporte, con el PAM8610 se podría conectar de la misma forma
Great work. It was interesting. Now i know what i will do tomorrow))
Good luck!
fake hai bhai...thodi electronics parh k dekhlo pehle
Sambil makan sahur hadir dan menyimak menambah ilmu,salam sukses selalu
Shorting amplifier output with other amplifier.
Nice.
Yes, thanks
پرچم ایرانو بالا بردی با ایده هات حجی❤❤❤🔥👌🤟
Wow that's cool concept, i think you should try with more powerful amps that would be pretty amazing if it turns out to be working properly 😍👍
That's the plan!
you can't bridge every amp, check datasheet!
Very good keep it up and do many videos about audio
Hello dear friend, thank you for watching a lot of videos about amplifiers and Bluetooth speakers. I will make a video🙏🙏👌
When i have 5 board then which value of capacitor and resistance i connect?
This is called real experiment full fun with dis
thanks
Wow, great 🧡🧡
Thank you 🤗
Hi
I want to diy multi connection splitter for audio signal.Sir can i use caps,resistor plus 5v supply.just like what you did sir.
Each module has only 3W, and 8 PAM8403 modules are superimposed and connected in parallel. How much W is this driven?
hi mr yan jun around 24+24watt
@@skillmake Thanks for sharing
Huh 3.7v =24w, hardly 5w maybe
@@skillmake are u made
All boards become dead if we use in parallel or series
@@sleepy9817 no waats it become dead
Genious I need a help, I choose speakers which is,
1 subwoofer 4ohm 25 watt and 2 full-range 4ohm 15w.
So how many of pam8403 I need to perallale?
I want to know the calculation for my understanding.
Bro can i use Two 8ohm 10w speakers and two 3w speakers and one 45W speaker with Three PAM8403 ?????
Would you mind making pam8610 parallel? I tried them but failed. Thanks.
Maybe I will test in the next videos🙏🙏
@@skillmake I am waiting for your actions.
try to use 5V 3A power supply with 470uf filter capacitor instead of parallel 3.7V mobile battery for better bass... in my own opinion 😸😸
🙏🙏👌👌
Many parallel speaker can get short circuit...try used just max 2ohm...
hi mr ary yt thanks for comment 🙏🙏
can you connect everything in the same way, but with only 1 amplifier? I wonder how much the result will be different
You can test it
@@skillmake No, i don't can)
1 amp will not be able to handle a load with is below 1ohm.
Yeah please do 1 vs 8 pam8403
Good Work brother
wont the ics get hot easily on that setup?
no dont get more hot me ahyon🙏🙏🙏
As an audio engineer with 10+ years of experience i can definitely say you dont have any research knowledge on how amplifier and speakers ohms works and matter in audio . I won't say stop doing what you love but learn for your past experience and improve yourself
Unless some of those drivers are 16 Ohm, those amps have got to be frying! I know one of those drivers was 4 Ohm. 30+ in audio!
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 czcams.com/channels/BoZGn08nBAxE9M5T53_UKg.html
That was amazing. I be looking at solder guns online wanting to buy one because I want to do this type of work someday I know it looks easy but it takes time to learn
Hello dear friend, please subscribe to my second channel so that I can create the content you deserve. Thank you. Just click on the link and subscribe to it.🙏🙏🙏🙏 czcams.com/channels/BoZGn08nBAxE9M5T53_UKg.html
I have 1x8ohm , 2x4ohm speaker how many pam 8403 do I need and how much power supply does it need ?
I tried it, but it doesn't sound. Can you give me a solution please?
This time you dun well solve ing ampere problem 🔥🔥🔥🔥🔥
Thanks for comment 🙏🙏🙏🙏
Best of the best
thanks
Os alto falante foram ligado em paralelo. Qual a impedância final ?
Olá querido amigo, acho que a potência de saída é de cerca de 48 watts
@@skillmake dijo IMPEDANCIA, no potencia.
Poner todas esas bocinas en paralelo debe sumar menos de 1 ohm. Fatal para muchos amplificadores.
اول فک کردم از این چنلای فیزوریه هندی هستی..😄
دمت گرم دادا
اگ شد ت تایتل ویدیو دو سه کلمه فارسی بزار ویوهات برن بالا
Nice job👍Keep it up.
سلام داداش شما ها از کجا میدونید من ایرانیام
واینکه خودم انگلیسی شروع کردم برا ایندش فارسی به درد نمیخوره 🙏🙏❤️
It work give 24 watt per channel but also impedance became 32 ohms so use for tweeters 16 ohms in series . You just parellel amp but also you need some balance resistor for futher protaction to balance gain
Thanks for your help, this video was for testing
Kya 8 PAM module 4-4 speakers dono taraf ke liye theek hai.
Matlb IC kabhi kharab to nhi hogi volume bhadane se
हाँ य़ह सही हैं
دمت گرم داداش باحال بود
موفق باشی
مرسی داداش
How many volts for the Elcho/capacitor?
😲Amazing 👏👏👏👏👏👍👍👍👍👍
Thanks 😄
Do you hear some noice in the circuit. Because i have this amplifier. But i connected before my phone its hear big noice. How could you achieved that
If you want to hear less noise, I recommend using a battery to power the module.🙏🙏
Wow.
Great Content. Is the Interesting
Tx.
Welcome!
R220k connected to vcc? Explain please
goooood
Thanks mr 😘😘
Make video on pam8610 amp board (use 6 board of pam8610) plzz requested man and do this same experiment
okkkkk🙏🙏
verry good i copy that thankyou
thanks for comment 🙏☺️
Why you added capacitors and resistors? What they do?
Hello my friend, we are doing this to increase the input power
@@skillmake the capacitors and resistors will help to avoid the distortion? when you up the volume?
Creative👍
Thank you 🙂🙏🙏
Nice one sir
Bro why you use capacitor in the circuit?
Sir i have a question
I got an amplifier of 15W+15W output and connect 5W speakers on it but when i open volume my speakers start cracking why
May i have to connect 15W speakers on it?
Use a higher powered speaker and control the input
Ola tudo bem? a utilização deste capacitor seria para essa divisão de frequencia? ou apenas para ruido?
Ele usou aqueles capacitores para desacoplamento de som
Maybe you must try tda7388 to make multi channel amplifier
Thank you for your comment
สุดครับ
thanks mr
Which value of capacitor uf and volt
22microfarad and 16volt
@@skillmake thanks
Can we use less than 8? Say like 3,4,5?
Just use a transistor or mosfet to amplify signal of 1 board it would be million times smaller and more efficient
gooood ❤️🙏
Mantap
🙏🙏🙏👌👌❤️❤️
Ada orang indo juga ya😂
Nice
Thanks mr asyari
why did you connect two inputs to 5v pin with caps and resistors. ?
for increased input power
@@skillmake Thank you..
@@chrisredfield5278 ❤️❤️
Brasil ❤
Obrigado pelo comentário
Bro we can add bt decoder ?
Coba bikin yang tp3116d2 di susun 3 lantai bang?🙏
sangat bermanfaat
a eso se le llama conexion modo bridge ?? esto incrementa la potencia manteniendo el voltage pero aumentando el consumo en miliamper, ciero ?
How many volts for the Elcho/capacitor?
If you measure the total impedance it will give a ridiculously low value that explains why they move so much with the music.
👍👍👍
8 placas PAM8403 em paralelo em 5v assegurando 8x5W=40W por canal!Top !
isso é certo? se eu usar 2 pam8610 vai dar 20w por canal?
no it just for test
no it just for test
@@skillmake you are so cute😂🤣
WOW~! Thanks for the good video~!^)^
Thanks for visiting❤️❤️
porque no hiciste la prueba con parlantes en caja acustica
Maine bhi socha tha ye idea but kbhi try nhi kiya
🙏🙏🙏mr ayush yadav
Bacano están esos módulos. de acuerdo a las necesidades..👍
🙏🙏🙏
Thank you im from việt nam
thanks
magazo !!! mejor que Beto el boticario ...
Mantap 👍
🙏🙏🙏🙏 thanks
Làm ×100 đi bạn
😮😮😮😂😂
Try X 100 bro .
I think very interesting than X 8 👍👍👍
I wait next ur videos X 100
@@darkside7786 💪💪💪🙏🙏ok ok mr johan ❤️❤️❤️
@@skillmake i waiting for next X100 bro 👍👍👍💪💪💪
mantap 👍👍👍👍
why u add resistor and capasitor between ( + ) and L R audio input
To increase the input power of the amplifier
Секрет очень простой, мощность что одной, что двадцати в паралелить будет одинаковая, тут хитрость в другом, динамические головки все в параллель, а это по сопротивлению будет менее одного ома, что и даёт прибавку в мощности)))
MANTAB BOSS .
❤️❤️👍👍
عالی داوش🇮🇷🇮🇷
Keren bang..kl di pakein 2 sub ngangkat g itu bang pam nya...
yes gooood
I think 1 amplifier is enough It depends on the Supply Power, Impedance of the speaker and also Voltage.
[ I = V/R ] If your speaker type is 4ohm and your supply voltage is 5v then.
[ 5 divided by 4 = 1.25A ] which means
[ 5 x 1.25 = 6.25watts ] 1 amp of current 6W runs to the Speaker.
Ex 2
If your speaker is 8ohm and your Supply voltage is 24v then.
[ 24V / 8ohm = *3A* ]
[ 24V x 3A = *72Watts* ]
Ex 3
So if you want 1,000Watts 24Volts runs to your Speaker Coil and 4ohms speaker Impedance then.
[ Watts / Voltage = Current ]
[ 1000w / 24v = *41 Amps* ]
Hope this helps to find a suitable speaker and amplifier and also power Supply DC to DC or AC to DC Supply
Hope will help your Calculations and also it Depend on the volume the Amplifier voltage drop because some of energy may not go through the speaker rather to Heat Due to Parasitic Inductance and Resistance of the speaker and Amplifier Components :)
QQ
Ex 3 is basically Wrong calculation but ex 2 and 1 is obviously correct.
@Black Pepper Usually your correct it depends on the wattage or impedance of the speaker so you can connect this tiny amplifiers in pararel so the components won't heat up and delivers more power depending on your supply power and the output voltage won't collapse :]
@Black Pepper can you give a calculation. Then we can choose the amplifier according to speaker.
You can give us 1 or 2 example like he did.
@@ReimuReimu_Animation can you give a calculation. Then we can choose the amplifier according to speaker.
You can give us 1 or 2 example like he did.
so vai dar mais potemcia se diminuair a quantidade de ohms pois ate vai ter mais corrente ea voltagem permanece ok
👌👌
Just about 5W is the maximum output since the voltage doesn't get any higher. 5 volts divided by 4 ohm speaker is just a bit over 1 amps. 5 times 1 is 5(Watts). RMS power is even lower!
it's only for test
@@skillmake But you are telling to people that each additional amplifier adds to the overall output power, which is NOT true and is misleading!! I've been reading your comments... Not very honest
you are right, its misleading, i used two modules in parllel and I did not get any extra power@@dfn03
Hello can you help me? I tried to make that project but once it's done there is no sound I'm using 5v voltage where is the problem?
use battery
@@skillmake wow this will sure solve his problem, u wasted so many people s money and time, now they get a trash
Hi, can you please suggest me a good Bluetooth audio amplifier?
module or speaker
Why you dont made it serial ?, to add more power?.. ?m err
ใช้เป็นแอมป์โมโน100วัตต์หน่อยครับ
ok mr phonkrit 🙏 thanks for comment