Axicube-I Manual. Assembling and Calibration (Edited)
Vložit
- čas přidán 26. 07. 2024
- Video from Apr 15, 2022 dedicated to assembling built-in digital angle finder Axicube-I for TSPROF K03 Sharpener.
5% discount with promo code YOUTSPROF
The only difference is that Axicube-I is resistant to water splashes, but not fully waterproof.
You can make an order on tsprof.us
Also, you may place an order via this phone number: +1 213-510-09-80
or write us here: sales@tsprof.com.
You also can get in touch with our dealer in
USA:
www.statesllc.com/
www.gritomatic.com/
whitemountainknives.com/
www.omahaknife.com/
www.blueridgeknives.com/
statesllc.com/
Europe:
www.knivesandtools.com/
tsprof.eu/
sharpinator.de/
www.baterky-noze.sk/
www.slipespesialisten.no/
Australia:
zanvak.com.au/
Buy a professional sharpener tool with rotating mechanism: shop.tsprof.com
Subscribe to TSPROF CZcams channel: / tsprofsharp. .
Welcome to our Instagram: / tsprof_en
Facebook: / tsprofen
00:00 - 00:22 Intro
00:23 - 01:15 What Axicube-I Comes with
01:16 - 01:53 Assembling Axicube-I
01:54 - 03:31 Start of Work
03:32 - 04:10 Calibration
04:11 - 04:47 Properties
04:48 - 05:20 End of Work
05:21 - 05:52 Conclusion - Jak na to + styl
Axicube worked perfectly for a couple months, now does not accurately give angle, and attempts to recalibrate do not work. Sets at anywhere between 17.6 and 19.9 on the 14 deg calibration angle with press and hold.
Defective? Hard reset?
Спасибо
What is the difference between the 2 different calibrations styles ? I have the wedge to calibrate with 1 clamp,
My kit also came with the 2 small metal bars to calibrate lowering the adjuster all the way and raising the extender , Why is there 2 separate ways can you please explain ? Thanks
Helllo! I am not sure that I understand which is the second type of calibration. There's just only one :) Indeed, it comes with 2 bars and each bar for each clamp. There' no difference in calibration at all. It's just for convenience to not remove them each time when calibrating.
Any news on when the axicube will finally be available for the kadet pro?
Sill working on this.
У меня уже есть сегодня взял для kadet pro ))))
So i calibrated axicube the way u showed, and when i double checked deviation with angle block cube comparing it to center console, deviation is 1.6 degree, so axicube is off by 1.6 degree
Please, shoot a video for us with the problem and send it to us to sales@tsprof.com. We'll examine the issue.
Is there a video using the axicube and the universal convex attachment on the KO3
There's no far. As soon as we find a suitable knife, we'll do. But the approach is the same. There's no difference at all.
ETA on re-stock (EU shop)?
How do you reset the cube itself back to 14 degrees? When I calibrate it says
14.6 degrees. Then If I do it again in the same spot it reads 13.8 degrees.
Just bought Pro Hunter and having issues with Axi-Cube. Thanks.
John, sorry for the late reponse. I understand the problem. Plese, contact us to sales@tsprof.com and say that Nick told you to contact him. I will provide you with a special video about how to fix it.
Hi, is there a troubleshooting manual or video?
Hello! What was the problem?
@@TSPROFSharpening it is ok I have already emailed, thank you
JUDAS PRIEST!!🤘😆🤘
😎🤘
Already fixed. Sorry for the inconveniece 🙃
my axicube shows 10.9 dps with the whole milled fillet clamps. am i doing this right?🤣
Not sure it I understand you :) Can you describe?
@@TSPROFSharpening oh, i think i fixed it now. one lf the whole milled clamp was way tighter than the other and wasn't seated properly in yhe crossbar so i got a wrong reading.
used it for about a month or two and now it won't start anymore, even though it's fully charged. what a disappointment😢
Hello! Please contact our customer service (sales@tsprof.com) we will see what we can do to solve this issue.