Zener diode voltage regulator, resistor calculation, हिंदी
Vložit
- čas přidán 5. 09. 2024
- The Zener diode as voltage regulator DC supply circuit, resistor calculation of ohms, wattage, electrical current and power loss is explained using ohms law with example in Hindi in this video.
The calculation of ohms and wattage of the resistor with the selection of resistor is explained. Zener diode wattage selection is explained.
An educational learning tutorial on electrical and electronics engineering 368 in Hindi by G K Agrawal. The lecture is given by a person with circuit design and industrial experience.
Note-- In the last slide, right side figure, read Zener diode current with the load as 0.02A, not 0.2A
Also, watch Ohms law wattage calculation
• Ohm’s law - Voltage Am...
Watch Zener diode in series and parallel
• Zener diode in Series,...
• Capacitor types AC vs ...
Also, watch AC neutral earth difference in Hindi
• Neutral और Earth wire ...
LinkedIn / g-k-agrawal
Twitter / gkagrawal1955
WordPress letusshareknow...
Facebook / gopalkrishna. .
Math Puzzles / @pahelisansar
Blog g-k-agrawal-el...
Membership / @gkagrawal2
In this video, you learned about the method of calculation and selection of resistor ohms, wattage and Zener wattage for a Zener based voltage regulator DC supply with Zener diode dc supply circuit using ohms law practical problem calculation and circuit analysis, zener diode in circuit.
#gkagrawal #ElectEnggByDesigner #ZenerDiode #DCSupply #Resistor #ResistorCalaculation
#Resistor #CircuitAnalysis #ElectricalCalculation #ElectronicCircuit
Correction, in the last 2 figures, right side, zener current with load will be 0.02A and not 0.2A. Watch and learn Zener diode resistor calculation
Join czcams.com/channels/O31rZS4_EDYJ8CGXiRZdxg.htmljoin
One more correction in ohms value of resistor when resistance coccects in parallel their ohms value shall remain same
@@muhammadsalman9134 Sir, greetings. Resistance Ohm value reduce in paralal & increase in series , Watt are also increase.
@@pradeep-rajnanavatijain752 Ok sir Now i understood thanks to tell..
Sir I want you mobile number
dear sir,you just surpassed all editing skills by using paper only
Old is gold knowledge
सर नमस्कार पहली बार कमेंट कर रहा हूं वीडियो बहुत देखे थे आपके बहुत इज्जत करता हूं आपकी आप जैसे लोगों को सामने आना चाहिए बहुत समय नई पीढ़ी में बहुत बड़ा बदलाव होता धन्यवाद सर
Super explain sir
Very good sir ap ache se smjate he Sunbber curcite me resistor & capacitor ka value calculate kase kre pl. Video banaye
बहुत बहुत धन्यवाद गुरूजी 🙏🙏❤🇮🇳
G K SAHB AAP BHOT DILSE SIKHARHEHYN BHOT SUKUN HOTAHYN
Sir ji very Good
बहुत धन्यवाद 🙏🙏गुरूजी
Thanks sir ji aapka bhot bhot dhanyawad
Good video sir g
I am your fan sir...Very nice explanation..you teach in such way that after listening the video my feeling is why I did not know such a easiest topic till date..God bless you.
GOOD VIDEO
Sir bhut dino ke bad aap ka vidyo aaya h
Sir please ek bar SCR,IGBT,or TRAIC ko multimeter se kaise test krtehai video banaiye.please sir
Jaise MOSFET ka video diagram banak samjhaye the osi trah
Wow very useful
Very helpful 👍
Thanks ji
Bahut achhi jankari di sir👍👍
Aap se request h ki ferrite core transformer winding calculation ka video banaye sir
Mushkil aasan karne wala tari ka hai yah
धन्यवाद सर
Namaste sir g 🙏
Great video, key points. Thanks for your help and support sir. Kindly make a video on analog oscillators.
Thanks for sharing of valuable information in easy way & neserry corrections.
much informative
Good that you found it useful
👌👌👌👍
Nice informations sir...
Thank you sir
Sir how to calculate dc motor current
Please make a video on this topic.
Great work sir, make more videos plz
Thank you
7:18 Sir ckt 2 me @ zener diode 0.02 Amp current hoga, 0.2 nahi.
Yes. It's important.
I think GK Sir suddenly caught the error during video but seemed ignoring not to break continuity. Moreover, I'm surprised that Sir ji ignored your comment.
Yes you are correct, current will be 0.02A and not 0.2A. I can not correct video now, but I will pointout in comment or descriptions
Ques. Sir मैने inverter phase के output तार का connection single pole 16 amp. Mcb मे किया है जिस साकेट मे inverter का connection है उस साकेट मे neutral व phase मिलाने पर ( touch करने पर ) mcb trip नही होती साकेट मे neutral main line का है
Thank you sir..
Sir 1led hi size 20X20mm 3.7V 10w ka battery hi 3.7V 15Ah ki hai sir resistor kon sa lage ga sir please bataiye
Sir without resistor zener diodes kaam Kare gaa
sir hamne ek house wiring kiye hai usame ek ab fault aa rha hai jab light hai tab fan sahi chal rha hai light jane ke bad jab inverter par koi load diya jata hai to inverter pr ka sabhi fan speed ho jaa rha hai Q???
bas inverter par aa rha hai fault koi bhi switch on krne par.
Ques. 1. Sir rccb मे ampier क्यु दिया जाता है जैसे
16amp. 25amp. 40amp.
घर मे 30ma का rccb लगवाना चाहिए
यह तो समझ आ गया लेकिन rccb कितने amp की लगानी चाहिए rccb मे amp क्या काम आता है rccb मे amp. क्यु दिया जाता है
Vah contact ki rating hai. Contact mey se pure ghar ki current bahti hai. Mera video RCCB breaker concept dekho.
Sir ji STABILIZER ki output phase wire single wire ko use kr skte h kya jese inverter mein hota h ek wire
Stabilizer ki input neutral to attach hi hoti h supply mein
Kya sirf ek wire ka use krke jha jrurat ho us load ko STABILIZER se chla skta h kya ek wire se 🙏🙏🙏
Sir ji STABILIZER ki input output neutral common hoti h sir inke ampere mein to Farq hota h na phir koi dikkat kyu nhi aati h 🙏🙏plz btaye
Sir, resistor parallel karne par to unka watt half ho jayega. 120 ohms 1 watt ki two resistors parallel me lagane se final resistor ki wattage to half watt ho jayegi na...????
Double ho jayegi.
Please reveel,if you can, what is the meaning and origin of word ( hartz) cycle
0.02 amp current Zener se jaayegi not 0.2 amp... Right 🙏
Yes, that is clarified in my comment 3 years back.
Ziner diode me maximum input volt kitni range tak rak skte hai agr 5v output lena ho
Yeh tho es per nirbhar karta hai ki, out load current kitni hai aur zener diode kitni power kaa hai.
@@GKAgrawal2 sir hmne 5amp ka load lena hai 12v output ka transistor use kiya hai TIP3055 aur voltage unregulated aa raha hai around 40v ke kreeb aur 8amp bhi aa raha hai kitne watt ka ziner use hoga
At least 50 watts zener, design not practical. The transistor may burn.
@@GKAgrawal2 thanku sir
0.2 A or 0.02 A ?
Sir 1.5 टन AC के लिए कितने amp. की mcb लगानी चाहिए
5 वोल्ट सप्लाई से मुझे 4.2 वोल्ट में कैसे बदलें मुझे कितने का रजिस्टेंस लगाना है
Itne din kaha the
Sir please make a video on Load Testing for SMPS ... How to test with fixed load resistor ? ... Currently i am working in a private organization where i perform testing of smps .. in testing we are adjusting input ac voltage and at the output side we connect a resistor .. and note the readings ... And from the testing board there are three indicator which are ac input voltage , ac input current and DC output voltage only ... I want to know how can this actually works without changing load resistor ( as i know we have to increase load current with low to high ) but here we are changing input voltage instead of output current . ... We test at three input voltage first 220 volts then 130 volts and then 300 volts ... Whenever we change input voltage then automatically current changes itself ( as per ohms law ) . But sir i have watched a lots of video on your channel . I don't remember which video was that exactly but in a video you said that the total power at primary will be the total power at the secondary side ( in other words you said the total power on input side is always equal to the output side ) .
But when i calculate the input current and voltage and then multiply to get input power and then calculate the fixed output DC voltage and resistance ( fixed load resistor ) but both values are not same 🙄 why ???
For example i test a laptop adapter which has 19vdc and 4 ampere maximum current rating .. so we attached a load resistor of 4.75ohms to get 4A constant current at the output .. and we change input voltage ... I want to know how this load test work without changing load ??? Please please reply sir.
Thank you
According to.me, the test you are doing is not the load test, but it is input voltage varation test at full load. This may come under routing test.
Check your documents for type test done if any.
Okay sir ... Thanks for your kind answer .. i request you , can you please tell me more about it ? Just like how it is different from load testing ? And which one is better for quality test performance ? I know what is load test and why it is used and its importance but i am not aware of input variation test ... what is it ? Why it is used ?what It's advantages ?
You can provide me a web link of any artical or video by which i can understand clearly .. i will be very thanksful to you 😊
@@ravilovekumar750326 pls send your contact number, I will describe regarding testing
@@kuldeeprawat4758 9990269589
Red mercury kia hai
Wa....modiji
There are 2 mistake in this video..
Pm Modi ji
𝙉𝙖𝙢𝙖𝙨𝙠𝙖𝙧
Thanks sir🙏