Other than FULLY turning the bottom screw, which does nothing but either hug or push the cover away from the body, here are some instructions I hope you find helpful. Location of attachment points: BOTTOM: Measuring 1 centimeter from the bottom corner along the bottom edge on each side, you will find one plastic hook attached to the back case clipping onto the internal plastic frame. A very thin flat blade screwdriver should release it. Otherwise no other hooks or snags along the bottom. SIDES: This is where the real fun begins. Strangely the back cover has inset attachment points, instead of between the case edge and the screen. 4 U-hook anchor points located at: 1). Horizontally: 1.8cm in from the outside edge, Vertically: 7.8cm up from the bottom outside edge 2). Horizontally: 1.8cm in from the outside edge, Vertically: 14.4cm up from the bottom outside edge 3). Horizontally: 1.8cm in from the outside edge, Vertically: 19.5cm up from the bottom outside edge 4). Horizontally: 1.8cm in from the outside edge, Vertically: 28.8cm up from the bottom outside edge These are the MOST difficult to disengage. Simply running a guitar pick or screwdriver or slidey bar between the edge and screen doesn’t work. In the past, I’ve been too gentle on the edges and like a surgeon separated the screen glass from the screen digitizer ruining the entire PC. My suggestion is to stick a screwdriver or a block of something inside the stand hole, between the cover and the body to keep up the pressure on the back case as you go along. Since there is nothing to release along the visual edges, you have to pull the bottom, slide along the side, relax, pull, slide, relax, technique along the bottom and edges until something eventually gives. Hopefully, it won’t be your patience. Fingernails are sometimes the best weapon. TOP: There are 8 cover plastic nibs spaced evenly along the top edge, 4 to the left and right of the camera slide switch. You might try inserting a very thin guitar pick along that edge. I didn’t because I was too afraid of killing another PC again. Getting the plastic cover away may be tricky. There are no delicate cables to worry about. You might get a string of rubber coming out from between the side edges but you can lightly glue them back, I used a slight brush of Elmers rubber glue. This is the worst case I’ve ever seen for repairs. The attachment points are way too hard and certainly not made to easily open. I would never suggest this PC because the next repair guy might have to buy you a new one out of his own pocket. Good luck friend, you're going to need it. 😄😉
EXCELLENT video. This was a difficult repair, but your video guided me through it. Thanks!
Other than FULLY turning the bottom screw, which does nothing but either hug or push the cover away from the body, here are some instructions I hope you find helpful.
Location of attachment points:
BOTTOM:
Measuring 1 centimeter from the bottom corner along the bottom edge on each side, you will find one plastic hook attached to the back case clipping onto the internal plastic frame. A very thin flat blade screwdriver should release it. Otherwise no other hooks or snags along the bottom.
SIDES:
This is where the real fun begins.
Strangely the back cover has inset attachment points, instead of between the case edge and the screen.
4 U-hook anchor points located at:
1). Horizontally: 1.8cm in from the outside edge, Vertically: 7.8cm up from the bottom outside edge
2). Horizontally: 1.8cm in from the outside edge, Vertically: 14.4cm up from the bottom outside edge
3). Horizontally: 1.8cm in from the outside edge, Vertically: 19.5cm up from the bottom outside edge
4). Horizontally: 1.8cm in from the outside edge, Vertically: 28.8cm up from the bottom outside edge
These are the MOST difficult to disengage. Simply running a guitar pick or screwdriver or slidey bar between the edge and screen doesn’t work. In the past, I’ve been too gentle on the edges and like a surgeon separated the screen glass from the screen digitizer ruining the entire PC. My suggestion is to stick a screwdriver or a block of something inside the stand hole, between the cover and the body to keep up the pressure on the back case as you go along. Since there is nothing to release along the visual edges, you have to pull the bottom, slide along the side, relax, pull, slide, relax, technique along the bottom and edges until something eventually gives. Hopefully, it won’t be your patience. Fingernails are sometimes the best weapon.
TOP:
There are 8 cover plastic nibs spaced evenly along the top edge, 4 to the left and right of the camera slide switch. You might try inserting a very thin guitar pick along that edge. I didn’t because I was too afraid of killing another PC again. Getting the plastic cover away may be tricky. There are no delicate cables to worry about. You might get a string of rubber coming out from between the side edges but you can lightly glue them back, I used a slight brush of Elmers rubber glue.
This is the worst case I’ve ever seen for repairs. The attachment points are way too hard and certainly not made to easily open. I would never suggest this PC because the next repair guy might have to buy you a new one out of his own pocket.
Good luck friend, you're going to need it. 😄😉
Good job! I need one display
PERFECT TUTORIAL. THANKS.....
I do❤❤❤ all model i love this job
Cost.?
Hii
Where u get the screen? And the price? Thank u
where didi the screen come from
Sir, I need this, how can I order pannel
bueno el video, la musica esta muy alta y es fastidiosa!!
Display kitne me aayega
Lenovo all in one ka display kitne me aayega?
Local is 16k original is I think 23K
@@lolmaster9029bro tf new pc costs 28k
half price is display bro
@@PARASJA8T
model ?
Where to buy panel and its cost? urjent
I bought it al Lenovo Direct, price aprox $120
I assume you broke the screen?
I PAID 125 DOLLAR FOR SCREEN
Ou acheter la dall svp
How do you entry USB boot mode !?
Without boot disk that mode appears
Display price
23k
Where to buy panel and its cost?
Any contact
Display price.?
display price
price
How to purchase online
23k
@@adepumahesh2579