HOMEMADE CYCLONE SEPARATOR - DUST COLLECTOR SYSTEM
Vložit
- čas přidán 2. 03. 2022
- #cycloneseparator #dustcollectorsystem
Today I build cyclone separator for my workshop dust collector system, from trial and error finally I found the best design for my cyclone separator, with this homemade cyclone separator the air velocity is increase drastically, I can get up to 32 m/s air velocity, actually this is beyond my expectation.
Instagram Jhon arief
@jhonariefdiy
FB page jhon Arief
/ workshopjhonarief
Support me on PayPal : paypal.me/jhonarief - Jak na to + styl
I personally don’t think that your video is to long. It shows an actual step by step process of your project. I like the video just like it is. Don’t shorten them.
Thank you
I have literally watched thousands of woodworking videos and often, I get disappointed by the kind of tools and materials they use because they were all beyond my imagination. Some were just too exotic and most were things, most cannot afford...But you my friend, has shown me something to inspire again. You are doing a wonderful work. Thank you.
The air velocity at the 3 inch pipe being 33 m/s gives 3x3x33 is about 300 “units” of airflow.
At the 4inch pipe it was 27m/s, giving 4x4x27 is about 430 of those same units.
So even though the velocity is higher it forms a serious constriction on the airflow.
It's not a flashy video, but it's real. You are making practical items with an elevated mathematical explanation. Great content sir, thank you.
It's valuable BECAUSE it's not flashy, in my opinion. Whenever a video is flashy I start wondering what shortcomings they're trying to distract me from. This is perfect!
@@branchandfoundry560
😊
@@davidlangston6927 If you get it, you get it 👊
Great project. Well narrated too.
Hi Jhon,
what a brilliant 3 series of dust collection videos! Amazing. Could supply you supply sizes (flanges )for your cyclone video (2nd video) in particular how you drew out your cone. Watching from Scotland 🏴 👋 Many thanks.
you're doing a great job! It's inspiring (and embarrassing ) to see a craftsman working with his own, hand made tools! Kudos to you!
Very nice! But a little disappointed to NOT see a real test with saw dust at the end of video. We can't wait 😉
Great workmanship, great narration!
Great build
Amazing work!
Nice work. That should work wonders for all your machines.
Yes.. A strong motor and a good impeller, reducing the intake at the Cyclone should surely increase air speed, which keeps the dust/chips moving..
The 1hp Motor with 2800RPMs must be a good strong motor. I noticed in that video, when you put the plywood over the impeller intake, there did not seem to be much motor slow down or drag.. I was wondering how much space/tolerance you had in your build of your impeller to increase the Static pressure, but, you really could not have made it much tighter than you did.. Excellent job... I will likely try to duplicate this some time in the future when I move into a larger shop.. Thank you.
That is awesome Jhon, great build videos!
Good jobs, thank for your share this video🙏💪
keren banget uyy, nunggu video test nya
keren keren videonya bang
Mantap bang.. Saja juga butuh mesin ini.. Untuk hisap debu amplasan cangkang kerang..
Excelente proyecto muy bien desarrollado y mejor ejecutado , un ciclón magnífico , muy necesario en cualquier carpintería , por favor subtítulos en español , gracias por compartir tanta creatividad y conocimientos , un saludo cordial y por supuesto un gran like desde Narón (Galicia) 🤓 🛠️ 🔝
Consider myself inspired!
Nice work, sounds like a jet :-)
Greate work!
amaizing
Berkelas, gak sabar nunggu full project nya jadi
makasih banyak mas yoyok🤗
Wuih mantaaap
Mantap 👍🏻👍🏻👍🏻👍🏻.. thanks my brother 🙏
Makasih mas🙏
Hadeer mas jhon 😁
Congratulations on the excellent work. Thanks for sharing. I will just build the top part of your project. It would be possible to provide the necessary measurements for my construction to look like yours. Thank you very much.
👍👍👍👍👍
Jhon, amazing manufacturing and precise design, very well done, looking forward to seeing the testing!!!
Thank you 👍
Siap2 bikin dust collector ni 😁😁
Jooss semangat masee
Great Video! nice work
can you please share the measurements q plan?
Excelente proyecto muy ilustrativo e interesante
Tengo una pregunta
¿Será que se pueden recojer particulan micrómetricas como harina o maizena?
Saludos y estaré muy agradecido si alguien aclara mi duda gracias
Where does the exhaust air go? Did you had any filter behind that during you measure the air velocity of the cyclone inlet.
But is it like a vacuum or shop vac - high pressure / low volume? So it may be blowing harder but not necessary picking up more dust??
Hi hi John, I made a change from traditional dust collector to cyclone conversion, however I am having a problem with the suction. The impellers work fine but they suck from the side extraction pipe as well as the bottom of the cone so the saw dust never goes down to the drum. Any idea of what I'm doing wrong?
Nice job! How did you transfer the drawing for the inlet onto the side of the top hat
Also, how did you decide the rotation
I use the pipe leftover of cut for the template, and the rotation I just follow the rotation of the impeller
Hello friend, a good hug from Santiago de Chile, I greet you. Would you be so kind as to give me the measures of the cyclone to make one of the same measure that you have.??? Thank you very much. I appreciate your kind friendship. Your work is very good. I appreciate it.
Amazing video, could the unit be installed with a wood housing? )
Of course it can be mounted on wooden frame
Great build and fantastic gain in air velocity! 👍
Do you think that using 5” hose instead of 4” would improve air suction even further?
It depend on you impeller size sir?
Because like you see in video I use inlet for impeller is 4" and inlet for cyclone is 3", that mean my pipping installation is using 3", my impeller if you see in part 1 impeller build I use 33cm impeller diameters and 5 cm width of the blade, that's the most suitable for my 1hp motor
@@jhonarief i have an impeller of 35cm diameter with 6 fins, would tou recommend using 4” or 5” hose?
@Alessandro Suppini with 6 fins I think 4" is the best velocity you will get if you reduce 1" from that 4" for the inlet cyclone, 6fin you will get loud noise and lower air velocity
@@jhonarief thank you for the advice 🙏
6:11 can u say this two part: height and diameter (up and down) thnx.
I really like your video's. Can you please center your voice instead of only on the left.
Thank you I think I need to replace my mic
Velocity increase can only happen when the cross section is smaller. (For the same blower) this has limitations up to a point when you reach max velocity. A cyclone adds resistance (drag) which is normal. Every obstacle in the flow causes drag. It just cannot happen that for the same diameter with added drag you get higher fpm. This means, that either your measure method is not consistent, or the diameter has changed.
yes, actually if you see the video you will find that my inlet diameters between impeller and cyclone are different, btw thank you.
@@jhonarief that explains. What is your CFM when fully assembled?
@@tamas7555 tomorrow i will upload the result for thesting this my diy dust collector with all the pipe instalation assembled
@@jhonarief thank you. We are sitting in the same boat, check out my version!
czcams.com/video/VpjlOGDOTSI/video.html
Hey, I'm a new subscriber and I'm just wondering why is there 3 hidden videos on this playlist? I mean what happened to them? If you don't mind me asking.
Which playlist that you see, let me check it
Oww in dust collector playlist that 3 videp is because failed to upload cause by interupted internet connection sir,
But already uploaded all parts, right now it just 3 parts of the dust collector but I will adding more video on my next DC project
@@jhonarief Man, it's just amazing what you do. Keep it up and thanks for sharing us such wonderful projects and I'm hoping to build one soon.
selamat sore pak, apakah aman membuat cyclone separator menggunakan sanyo? kebetulan ada sanyo tidak terpakai karena sudah ganti jet pump.. terimakasih
Gak rekomendasi om, soalnya powernya kecil klo menggunakan pompa air
@@jhonarief ohh iyaa pak terimakasih informasinya, untung belum di bikin, kalau sudah jadi nanti menyesal 😂🙏
Watch later dulu, lanjut nanti
Asiaaaap
my left ear....
1
Mantap pertamax
13
bandsaw nya berapa inch om ???
14" om
@@jhonarief 🙏🙏
klo pesan sama om boleh 😂😂. mesinnya kita
Untuk saat ini masih belum buka order om mungkin habis lebaran aja
Pak arif kalau pesan ini apa bisa ? Dan biayanya jadi berapa ya pak
maaf mas untuk saat ini saya belum bisa produksi untuk pesanan
@@jhonarief siapp, menginspirasi terus ya pak, terimakasih
@@ThePutrayasa terimakasih kembali mas🙏👍