All About HC-05 For CNC Shield and MKS DLC

In this video we are going to talk all about HC-05 Bluetooth module from A to Z for using in GRBL.
1- A short information about Bluetooth module 00:00
2- Show you the easiest way to connect to Bluetooth module and config it from arduino 01:26
3- Show you the most useful commands in AT mode and how to change them 06:15
4- How to Wiring HC-05 to connect to CNC shield or MKS DLC or other boards 12:02
5- Connect HC-05 to CNC shield and test it with Android App (GRBL Controller) 19:42
6- Connect HC-05 to MKS DLS and test it with Android App (GRBL Controller) 25:14
GrblController apk:
play.google.com/store/apps/de...
Don't Forget to Comment , Share & subscribe
تو این ویدئو قراره درباره ماژول بلوتوث 05 صحبت کنیم و از سیر تا پیازش رو برای استفاده تو جی آر بی ال داشته باشیم
1- یه کمی درباره ماژول بلوتوث - 00:00
2- ساده ترین راه ارتباط و تنظیم ماژول بلوتوث از طریق آردوینو - 01:26
3- چند تا کد دستوری بلوتوث رو نشون بدم و ببینیم که چطوری تغییرشون بدیم - 06:15
4- چطوری سیم کشی این ماژول رو آماده کنیم تا به شیلد سی ان سی یا برد دیگه ای وصل بشه - 12:02
5- وصل کردن ماژول بلوتوث به شیلد سی ان سی از طریق اندروید و برنامه گوشی - 19:42
6- وصل کردن ماژول بلوتوث به برد ام کی اس از طریق اندروید و برنامه گوشی - 25:14
برنامه اندروید:
play.google.com/store/apps/de...
کامنت ، اشتراک و سابسکرایب فراموش نشه

[@pedramkabiri687]

بسیار عالی
موفق باشی مهندس

[@manifa59]

همچنین ، امیدوارم به کار دوستان بیاد 👍

[@pedramkabiri687]

good luck

[@manifa59]

U 2

[@rafa_el9638]

Hey friend, did you solder the Arduino p4 to the Shield V3 terminal? I noticed that you are powering it through the P4 from Arduino

[@manifa59]

Hi
If you mean how I power the CNC shield through Arduino , I just solder VIN pin of CNC shield to positive terminal of Shield and now I can power both from power of Arduino.

[@rafa_el9638]

@@manifa59 just positive pin or negative as well? I want do this because HC05 only works by powering the Arduino, both with 12V in this case.
Thanks for answering me.

[@manifa59]

Yes
just positive pin. negative comes from pin headers and no need for wiring.

[@rafa_el9638]

@@manifa59 In my case I already have a P4 on the CNC Shield V3, if I solder it this way it will power the Arduino in the same way, right?
I'm powering a 12V fan and the Shield V3, in which case will I power the Arduino too?

[@rafa_el9638]

Plug P4 is soldered with a wire and is on back case, then I feed it through the Shield V3, I will solder a wire to Arduino and test it.

[@pablofelipeportelanunespab6633]

Aonde posso encontrar ressistor 1k e 2k

[@manifa59]

to buy:
1k resistor: www.amazon.com/Projects-100EP5141K00-Ohm-Resistors-Pack/dp/B0185FGTSS/ref=mp_s_a_1_1?keywords=1k+ohm&qid=1671400091&sr=8-1
2k resistor: www.amazon.com/Projects-25EP5142K00-Ohm-Resistors-Pack/dp/B01F06T4PU/ref=mp_s_a_1_5?crid=1JLGFMMEBMDA0&keywords=2k+ohm&qid=1671400140&sprefix=ohm%2Caps%2C616&sr=8-5