the Flipsky 75100 Alu PCB's and new Pro's also have 3 electrolytics and 3 ceramics in the same sort of setup just like the Spintend, seem to also have 3 NTC's the new Flipsky (75100 and 75200) Pro V2 series are also directly compatible with unmodified vesc firmware which probably means 3 sensors aswell the X9000, Torp, Flipsky, Makerbase and KO use Huayi HYG015N10NS1TA fets i know Spintend used JieJie JMSH1001 fets in some other Ubox's but i don't know what they use in the 150
I think Spintend uses Jie Jie in everything. I did later confirm that the 85-150 uses the SH1001 from Jie Jie. 85-250 does as well...just double the amount.
btw makerbase is going HARD now, they made a controller thats basically a 75200 but redesigned with real phase filters, INA241 amps, phase shunts, inbuilt bluetooth and imu, remote on/off etc.. all the good stuff with the HYG fets, and for like €125 off ali with 21% VAT it's called the 84200HP it doesn't have the creme de la creme current path but no doubt best "VESC" alternative for the price
I've been looking at the Pro series from Flipsky. Makerbase and Flipsky are one and the same. Looking at the Pro series they are effectively the same build as a Spintend in every way...including current sense amps and a very few ceramic caps. Well except the mosfet used. It's hilarious that Flipsky calls following the minimum specs for VESC their "pro" product line!
@@de-bodgery yea, atleast the Makerbase 84200HP is different tho, the older 75 series was the exact same as the Flipskys and the 84200HP is an actual different development, by no means perfect but hey Makerbase has it for way less money and actual high side phase sensing lol
@@BH4x0r High side phase current sensing? What's that? Shunts are on the low side to deal with certain facts of voltage spikes that you don't have to deal with as low side shunts. Current sense loops are 100% disconnected from the phases and are neither high or low side. I guess I'd like to see one of these Makerbase 84200 controllers. So far, everything I've ever seen from them is sold as is by Flipsky...aka one and the same company for all intents and purposes!
@@de-bodgery i mean actual phase shunts i.e. after the fets before going into the motor wires like in Benjamins 75V controllers, they're using the new INA241A's which is the 120V version of the INA240s that were/are used on the actual Vesc 75 series (by Vedder) my apologies for not explaining stuff properly sometimes, English is not my first language
thanks for the upload. been waiting for your videos
the Flipsky 75100 Alu PCB's and new Pro's also have 3 electrolytics and 3 ceramics in the same sort of setup just like the Spintend, seem to also have 3 NTC's
the new Flipsky (75100 and 75200) Pro V2 series are also directly compatible with unmodified vesc firmware which probably means 3 sensors aswell
the X9000, Torp, Flipsky, Makerbase and KO use Huayi HYG015N10NS1TA fets
i know Spintend used JieJie JMSH1001 fets in some other Ubox's but i don't know what they use in the 150
I think Spintend uses Jie Jie in everything. I did later confirm that the 85-150 uses the SH1001 from Jie Jie. 85-250 does as well...just double the amount.
keep going man🎉
Great content as usual, well done mate! :)
couldn't have done it without you!
btw makerbase is going HARD now, they made a controller thats basically a 75200 but redesigned with real phase filters, INA241 amps, phase shunts, inbuilt bluetooth and imu, remote on/off etc.. all the good stuff
with the HYG fets, and for like €125 off ali with 21% VAT
it's called the 84200HP
it doesn't have the creme de la creme current path but no doubt best "VESC" alternative for the price
I've been looking at the Pro series from Flipsky. Makerbase and Flipsky are one and the same. Looking at the Pro series they are effectively the same build as a Spintend in every way...including current sense amps and a very few ceramic caps. Well except the mosfet used. It's hilarious that Flipsky calls following the minimum specs for VESC their "pro" product line!
@@de-bodgery yea, atleast the Makerbase 84200HP is different tho, the older 75 series was the exact same as the Flipskys and the 84200HP is an actual different development, by no means perfect but hey Makerbase has it for way less money and actual high side phase sensing lol
@@BH4x0r High side phase current sensing? What's that? Shunts are on the low side to deal with certain facts of voltage spikes that you don't have to deal with as low side shunts. Current sense loops are 100% disconnected from the phases and are neither high or low side. I guess I'd like to see one of these Makerbase 84200 controllers. So far, everything I've ever seen from them is sold as is by Flipsky...aka one and the same company for all intents and purposes!
@@BH4x0r I'd like to see this controller.
@@de-bodgery i mean actual phase shunts i.e. after the fets before going into the motor wires like in Benjamins 75V controllers, they're using the new INA241A's which is the 120V version of the INA240s that were/are used on the actual Vesc 75 series (by Vedder)
my apologies for not explaining stuff properly sometimes, English is not my first language
Hey man what happened to your home setup? Missing the videos still love the content
See my last video.
@@de-bodgery oh shit sorry to hear the bad news
how much phase amps does it make ?
spintend.com