"ТАЛАНТЛИВЫЕ ЭЛЕКТРИКИ"! ЭТО ПИ...ДЕЦ, ТОВАРИЩИ)))) Я здесь увидел только "талантливых" маляров, мотальщиков и слесарей, забивающих болты молотом!!! )))
1) Медный провод первичной обмотки был БУ с налипшей старой изоляцией?!! 2) Изоляция катушек не была пропитана полностью, а только верхний слой?! 3) Трансформаторное масло, которым заливали трансформатор пенилось?! 4) Масломерное стекло на баке расширителе при покраске и не думали заклеивать. 5) Для изоляции использовался в основном картон и дерево 6) В процессе испытаний была снята только ВАХ трансформатора?! Эти парни никогда без работы не останутся. Видно по количеству перематываемых ими трансформаторов. Но лучше так, чем сидеть вообще без света.
@@meerasiftalpur1388 Why worry? You need to measure the tangent phi. And in order not to face the problems of transformer oil, you need to switch to narrower medium voltage transformers.
Я в самаре на трансформаторном заводе работал, там намотчики на специальных станках катушки делали, а тут практически в ручную 😄 жаль не показали как сердечники магнитопровода штампуют по виду на наши похожи были 😀
@@meytv5691 У меня лежит,3 перфоратора,и одна жисковая пила. На всех сгорел статор. Перемотать часа два пропитать лаком и готово. Думал на..... надо. Зашел посмотрел цены,и начал искать провод.Кончается дешевый китайский ширпотреб. Разорили всех дешовым товаром ,и теперь подняли цены. Китайцы более 5000 лет государству. Теперь перемотать не так тяготит по нынешним ценам.
У нас сами провод из алюминиевой катанки делают и изолируют. Потом почти так же наматывают на старом оборудовании. На специальных современных станках катушки тоже делают.
@@frendofkromanions не совсем из алюминиевой они комбинируются. На этом видео собирали трансформатор по типу нашего ТО-630 только более кустарным способом. Неудивлюсь если они взяли старый трансформатор и попросту перемотали его
законы ютуба, чем заманчивее название, пусть и не правдоподобное, тем больше просмотров. по факту то да, не создали а перемотали первичку вторичка осталась черная подпаленая
The guys who put those things in service must have balls of steel. I would never dare to switch that thing on when I am not at least half a mile away. If there are air bubbles in the oil and the insulation breaks down, a transformer like that hums very loud for a few seconds and then it blasts off like a 500 pound WW2 dam buster bomb. No chance to switch it off in time. I've seen it happen more than once.
@@gengetoneke10 If that thing shorts out internally, you have several megawatts of power which have to go somewhere. No pressure relief valve can handle that sort of power transferred to steam pressure.
@@gengetoneke10 depends on what kind of oil. some oil can be flammable, and if the transformer is completely air sealed then internal arcing will build up pressure inside of it and explode.
I get it when I see these guys rewinding motor coils or refurbishing lead acid batteries etc. Some of their knack for learning a trade and being good at pumping out the same thing over and over is impressive, but being cleverly resourceful in a poor country can only get you so far. The way they slap these things together just reminds me of people who are repeating a process without much thought into the physics behind it. It looked like they literally just poured oil into this thing through an open cap at the tank. That's the type of shit I might do at home dicking around with some self wound HV transformer where it's just tossed in oil. Yea that might work for a little while slightly helping resist arcs wherever the oil has nicely impregnated and filled. You have to wonder how they are even in business but the more I think about it the more impressed I get. These guys know what they're doing but they don't.. They are highly efficient at somehow creating the bottom of the barrel in order to actually turn a profit from it and are somehow doing it. Someone who is paying so much less is going to know what they are getting.
This transformer would not be very efficient due to bad harmonics, BUT would be far less expensive to produce as long as resources were reused. This may become a bit more warm under heavy load, but in a third world nation, less load could be expected. This is far beyond high school level maths.
I used to design transformers like this and the winding assemblies should be dried in an autoclave before being assembled into the housings, and when filling with mineral oil this should be done over a couple of days under vacuum to remove any gasses from the oil and make sure the oil penetrates right into the core of the windings leaving no voids. These transformers risk air pockets in the windings causing arcing when energised. Would be so dangerous being around these when they get put into service.
It's Pakistan a poor country. Compare their manufacturing with that of Indias' and it's rudimentary/stone age. Unfortunate state of affairs in Pakistan.
Damn, this is the worst transformer construction I've ever seen, I can't even believe that they just put those bolt in with a wrench and throw all the torque specifications out the window
@@AKAtheA not india. India exports transformers to around 150 countries from US to Europe to Africa and Asia. In the year 2020-2021 (Apr-Nov), India has exported Transformers worth of 1369.98 USD million. The total volume of export in 2020-2021 (Apr-Nov) was around 54777949.
Super fun to watch them build this, that said not sure I'd classify these guys as "electricians" any more than I'd classify guys stamping out metal parts for a car as "mechanics" unless the terminology is just different over there.
Safety not just for the workers. I also wonder how save those devices are in the end! And at 13:10, you can see how the QA inspector is also watching a CZcams video on his phone while testing ...
@Darrell Dobson Obviously, entire transformer is so cheaply made you expect them to splurge on Rustoleum paint, which is one of the best brands of paints in the world!
In fact, you can manufacture ALMOST anything you need. In Cuba, for example, there are no clothing stores, cuz the clothes are made by Cubans themselves. Just like it was done here in the US, in the 50's and 60's. A sewing machine is all that is needed.
"ТАЛАНТЛИВЫЕ ЭЛЕКТРИКИ" (из Пакистана?) 😂 похоже на новый мем вроде "БРИТАНСКИЕ УЧЕНЫЕ" особенно впечатлила пропитка катушек лаком - аплодирую стоя такому лайфхаку
While at present I do not speak your language, I can learn! I feel it would be amazing to work with you and learn from you with your hands on approach to technology! Great Job!
Где талант ? Это получается что любой работник добросовестно и исправно исполняющий свои обязанности талантлив ? Тогда получается что например работники автозавода - концентрация талантов ? Ну вы даёте ...
Так и есть.В любом заводе,или производстве есть незаменимыйе люди.Талантливые.Смотри как они собрали трансформатор с простыми дедовскими инструментами.И тепер представ что произайдет, если у них будет технологии 21 _го века?(и между ними не надо завидовать.🙂)
It looks like a 20 KV to 380 V oil - cooled transformer. The way they build it will make it fail after one year, instead of the twenty years normally expected by a static machine. We phased out oil cooled transformers twenty years ago in favour of ceramic transformers. The old transformers were a safety hazard, as the oil is highly flammable, and the vapours are explosive. Personally, I prefer properly built oil cooled transformers, as they have a better resistance to transients and peak loads. PS it is the first time I've seen a petrol powered forklift...
@@micah66048 US has to contend with highly dispersed rural housing, which is an unknown thing here in the UK. US utility companies can't build a substation for each house spaced one mile apart, only to allow the use of a ceramic transformer. So they run a medium voltage (11 - 13 KV) line and use a cheap and rugged oil transformer, placed on the top of a pole, for each house or group of houses...
Это обыкновенный капитальный ремонт трансформатора. Причём провод на высоковольтную катушку использовался вторичный. И не показан процесс испытания транса. Как говорят в России просто колхоз.
I work 26 years in a big factory of big transformers to 400 MVA with 200 tons ,for big electric power sistems . It was in Roumania and his name was Electroputere Craiova , we work for Fuji , Japan.
Я закончил политех по специальности техника высоких напряжений. Нам привывали трепетное и аккуратное отношение к такому роду техники. Помню на практике шихтовали измерительный трансформатор специальной формы, так зав-кафедры стоял над нами и следил за тем как мы каждую пластину набирали, и с ужасом повторял:," Акуратней, ато будет пожар метала". И мы с дрожащими руками пластинку за пластинкой набирали магнитную систему. Про испытания я вообще молчу, начиная от техники безопасности, заканчивач оформлением результатов и документацией. Или высоковольтный ввод: для некоторых это выглядит как труба, на которую намотан картон и фольга, а для высоковольтников - это система выравнивания электрического поля рассчитаная с учётом краевого эффекта на границе рубашки. Я это к тому что у мастеров на видео наверное золотые руки, но глубокого понимания того что происходит в технике такого рода скорее всего нету. Как следствие - отношение к тому что они делают. На самом деле это не очень хорошо, потому что результат из разряда и так пойдет затягивает. Но больше всего насмешил некоторые комментарии типа: импортозамещение в деле. Искренне желаю чтобы в россии импортозамещение проходило именно так)))
Такое работает по счастливой случайности и воли божьей (или кто там у них). Воспроизводимостью, надёжностью, да и просто достижением паспортных характеристик там и не пахнет.
Eu também amo essa parte de equipamentos. Sou engenheiro eletricista também e já trabalhei com trafos e é muito satisfatório ver um trabalho bem feito assim
Isso apareceu na minha timeline agora não consigo mais parar de ver esses videos, é muito interessante e dahora ver como é feito os transformadores e eu que sou um cara que ama eletronica e essas coisas de engenharia então so me faz ficar mais fascinado por essa area.
*These are postWWII transformers. They suffer from arcing and electric charge leakage and permeativity capacitance functional issues. About time new models are introduced.*
Yea ok sure. Transformers have not changed much over the years. Yes we have some newer types but In most countries the basic steps of making them which they are doing is still used .
Прозванивают мультиметром или омметром, а здесь уже что-то больше похоже на нагрузочное испытание. Правда, высокая сторона, похоже, так и осталась в воздухе. Да и перекос по току немаленький
@@user-ne5cb5rm3n Если на всех вольтметрах есть какие-то цифры - это значит, что транс прошел испытания!) Перекос, не перекос) Кому это интересно?) Главное, что бы транс напряжение выдавал)))
@@micah66048 to his defence he did paint it and there are paints on the market that combine antirust, base coat and finishing coat in one. On the other side you are probably right and this oils can absorb watter and become conductive
@@dadaselectro4794 that was also a very thin coat of paint and with absolute zero proper pretreatment before coating. its better than leaving it uncoated for sure but wont last ten years
Сейчас бы точно никто такой трансформатор перематывать бы не стал! Молодëжи ничего не надо! Перевели бы подстанцию на инверторные схемы, а трансформатор работавший ещё со времён СССР раздербанили бы на медь! Привыкли жить хорошо!
Beneath other things, the transformer hast to be evacuated before being filled with oil and the oil has to enter the vessel from the bottom, to enable the remaining air to go to the top.
Судя по названию каждый кто умеет махать кисточкой и мотать проволоку является талантливым электриком. Браво. Я просто похлопаю👏👏
За то не сидят, не ноют, этого нет, того нет, другого не дают, работают люди.
Блин индусы,наш автопром преплюноли.думал только наши кисточкой по ржавчине могут
талантливый айтишник без электричества даже арифмометр не на чертит на ватмане)))
Ремонт, а не создание! Талантища блеа
@@user-tp2si5lb8y это не ржавчина, это грунтовка
"ТАЛАНТЛИВЫЕ ЭЛЕКТРИКИ"! ЭТО ПИ...ДЕЦ, ТОВАРИЩИ)))) Я здесь увидел только "талантливых" маляров, мотальщиков и слесарей, забивающих болты молотом!!! )))
Так у них, там на каждом видео, все талантливые 🙂
Это пиздец конечно, болты молотком и ещё с умным видом
Я В АХУЕ С НИХ 😆😂🤣😅
Зато за два дня это видео просмотрело 2миллиона, и ещё комментарии оставили))))
@@user-hd2kb8sg6s АГА
Эти чуваки не останутся без работы. Намотал, сгорел, перемотал, сгорел, и так далее
а. ну тогда ...убрать их) С СЕМЬЯМИ)
та то я слесарь, понял?
Тем временем в России: украл, выпил, в тюрьму! и так далее
@@goldenbird2994 далее?
@@goldenbird2994 ну ладно, ладно) если ты не понял) то...ну а если понял) пове зло
1) Медный провод первичной обмотки был БУ с налипшей старой изоляцией?!!
2) Изоляция катушек не была пропитана полностью, а только верхний слой?!
3) Трансформаторное масло, которым заливали трансформатор пенилось?!
4) Масломерное стекло на баке расширителе при покраске и не думали заклеивать.
5) Для изоляции использовался в основном картон и дерево
6) В процессе испытаний была снята только ВАХ трансформатора?!
Эти парни никогда без работы не останутся. Видно по количеству перематываемых ими трансформаторов. Но лучше так, чем сидеть вообще без света.
Пенилось оно в аспирационной установке (если не ошибаюсь в её названии). Там, где масло сушится.
The wire used already insulated
Don't worry they doing this for years may be some part of making missing
@@babarsaleem2861 and from many years we are facing problems? we should be worry now
@@meerasiftalpur1388 Why worry?
You need to measure the tangent phi.
And in order not to face the problems of transformer oil, you need to switch to narrower medium voltage transformers.
Nice.
Now I know how it was done in 1894 AD.
Precisely. 1800's called and they want their transformer back.
Ich würde gerne mahl so einen Trafo nach ISO 9001 testen...
Der Iso Widerstand währe auch sehr interessant.
Was meinst du warum die immer so viel Arbeit haben? Die halten keine Minute unter Last
Я в самаре на трансформаторном заводе работал, там намотчики на специальных станках катушки делали, а тут практически в ручную 😄 жаль не показали как сердечники магнитопровода штампуют по виду на наши похожи были 😀
Митхун Чакраборти Электрикс представляет.😁
@@meytv5691 У меня лежит,3 перфоратора,и одна жисковая пила. На всех сгорел статор. Перемотать часа два пропитать лаком и готово. Думал на..... надо. Зашел посмотрел цены,и начал искать провод.Кончается дешевый китайский ширпотреб. Разорили всех дешовым товаром ,и теперь подняли цены. Китайцы более 5000 лет государству. Теперь перемотать не так тяготит по нынешним ценам.
@@user-wi3ox6zi5g бизнес делай давай.😁
У нас сами провод из алюминиевой катанки делают и изолируют. Потом почти так же наматывают на старом оборудовании. На специальных современных станках катушки тоже делают.
@@frendofkromanions не совсем из алюминиевой они комбинируются. На этом видео собирали трансформатор по типу нашего ТО-630 только более кустарным способом. Неудивлюсь если они взяли старый трансформатор и попросту перемотали его
I used to wind permanent magnet DC motor armatures years ago. Amazing this is still done in this way by hand! Talented chaps indeed. Great work.
This video is transformative.
lol
Без шума и пыли! Молодцы ребята!
Молодцы! Поражаюсь таким видео. Вот это настоящие работяги.
Рад, что вам это нравится. Продолжайте смотреть наш канал.
Видео:как с б/у транса намотать новый.
"Гениальные" электрики.
законы ютуба, чем заманчивее название, пусть и не правдоподобное, тем больше просмотров. по факту то да, не создали а перемотали первичку вторичка осталась черная подпаленая
@@MsMrak666 Трансформаторы такой мощности вообще запрещено так перематывать!!!Здесь нельзя применять радиокартон,только негорючие материалы...
@@user-jg4oi5eg2y Если дойдет до того что этот картон воспламенится , то ничего уже этот трансформатор не спасет )
@@user-jg4oi5eg2y это индусы, им всё можно
Хитрые электрики🙂
The guys who put those things in service must have balls of steel. I would never dare to switch that thing on when I am not at least half a mile away. If there are air bubbles in the oil and the insulation breaks down, a transformer like that hums very loud for a few seconds and then it blasts off like a 500 pound WW2 dam buster bomb. No chance to switch it off in time. I've seen it happen more than once.
Really? Is it the oil that explodes?
made out of junk wow
@@gengetoneke10 If that thing shorts out internally, you have several megawatts of power which have to go somewhere. No pressure relief valve can handle that sort of power transferred to steam pressure.
@@gengetoneke10 depends on what kind of oil. some oil can be flammable, and if the transformer is completely air sealed then internal arcing will build up pressure inside of it and explode.
I get it when I see these guys rewinding motor coils or refurbishing lead acid batteries etc. Some of their knack for learning a trade and being good at pumping out the same thing over and over is impressive, but being cleverly resourceful in a poor country can only get you so far. The way they slap these things together just reminds me of people who are repeating a process without much thought into the physics behind it. It looked like they literally just poured oil into this thing through an open cap at the tank. That's the type of shit I might do at home dicking around with some self wound HV transformer where it's just tossed in oil. Yea that might work for a little while slightly helping resist arcs wherever the oil has nicely impregnated and filled. You have to wonder how they are even in business but the more I think about it the more impressed I get. These guys know what they're doing but they don't.. They are highly efficient at somehow creating the bottom of the barrel in order to actually turn a profit from it and are somehow doing it. Someone who is paying so much less is going to know what they are getting.
Thank you for this video now I can finally build my own transformer 🙂
Wait what
Go ahead 😂
“Mom we need a new SIEMENS transformer”
“But we have a transformer at home”
Transformer at home:
Lmao this is so accurate. They produced an inefficient bomb and a death trap.
and then they fill it with 15w-40
I never use word Mom and Siemens, not in the same sentence and not in polite company.
Also: why using a mask when spraying paint? My grandpa never wore a mask, why should I?
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html
Finally, an impact wrench
Still holding out on chairs and tables
Ya an they used it like a miser
В Пакистане всё производят сами, от иголок до автомобиля. Это страна завод.
💐💐
😂😂😂
Inclusive bombas atômicas 😂😂😂
Yes the best cannabis genetics come from this region of the world heavy duty indicas
Правда ничего не работает больше суток
Не пропадут такие умельцы
Big respect for working people!
Incredible how lot of manual work goes into this. I've winded small SMPS transformers before and I can't imagine doing big ones like this.
The process of making a transformer is not often seen. This is a good video.😀
This transformer would not be very efficient due to bad harmonics, BUT would be far less expensive to produce as long as resources were reused.
This may become a bit more warm under heavy load, but in a third world nation, less load could be expected.
This is far beyond high school level maths.
This is a very bad example, this transformer is tragic.
I used to design transformers like this and the winding assemblies should be dried in an autoclave before being assembled into the housings, and when filling with mineral oil this should be done over a couple of days under vacuum to remove any gasses from the oil and make sure the oil penetrates right into the core of the windings leaving no voids. These transformers risk air pockets in the windings causing arcing when energised. Would be so dangerous being around these when they get put into service.
Pretty sure that shipping container thing was the “autoclave”
Yeah, that container had rubber seals around the doors and a pressure gauge so that’s probably their big vaccum
It's Pakistan a poor country. Compare their manufacturing with that of Indias' and it's rudimentary/stone age. Unfortunate state of affairs in Pakistan.
@@dare-er7sw *Please shut up. Stop politicising every time you come across Pakistan videos and end up getting triggered.*
Damn, this is the worst transformer construction I've ever seen, I can't even believe that they just put those bolt in with a wrench and throw all the torque specifications out the window
Уровень советского техникума 1980-85 годов но там работали парни 18-19 лет.
You do what you gotta do and these boys got it done.
the transformer is not built but only repaired.
it is disassembled, a burnt winding is redone and reassembled.
@Sheila Walker keep in mind this is Pakistan (or India?) we're talking about, 50°C ambient is quite possible, these have run hot.
@@AKAtheA not india. India exports transformers to around 150 countries from US to Europe to Africa and Asia. In the year 2020-2021 (Apr-Nov), India has exported Transformers worth of 1369.98 USD million. The total volume of export in 2020-2021 (Apr-Nov) was around 54777949.
@@AKAtheA
Its Pakistan
That is some impressive back yard build right there.
Super fun to watch them build this, that said not sure I'd classify these guys as "electricians" any more than I'd classify guys stamping out metal parts for a car as "mechanics" unless the terminology is just different over there.
same. the test guys are but everyone else just doing what they are told
Sua
The level of health and safety is the most impressive
zero
Come with me and you'll be in a world of Osha violations
Safety-flip-flops, beard fume protectors....
Safety not just for the workers. I also wonder how save those devices are in the end!
And at 13:10, you can see how the QA inspector is also watching a CZcams video on his phone while testing ...
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html
Весь талант этих электриков, в том что они медь в скупку не сдали.
Но скорее всего. им этого не позволил хозяин меди.
точняк🤣
где ты тут электриков увидел? максимум слесаря.
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html
@@kjlas8 В отличии от тебя балабол пацаны хоть что то сделали)
Они на глазах, из десятков тысяч рупий делают милионы!
I loved the part where they painted the rusty parts brown. Very professional.
That was red oxide metal primer. They painted entire thing black later on.
@Darrell Dobson Obviously, entire transformer is so cheaply made you expect them to splurge on Rustoleum paint, which is one of the best brands of paints in the world!
They put paper between those clamping devices to prevent currents trough those bolts. They know what they are doing.
That's truly incredible.
After Watching CZcams videos I feel like I can manufacture almost everything on my own...😁😁😁
In fact, you can manufacture ALMOST anything you need. In Cuba, for example, there are no clothing stores, cuz the clothes are made by Cubans themselves. Just like it was done here in the US, in the 50's and 60's. A sewing machine is all that is needed.
Dziekuje za komentarz to wizja dla ciebie czcams.com/video/cTXZlK9x9fMt/video.htmlyhunfhujhgfdcgvhjk
"ТАЛАНТЛИВЫЕ ЭЛЕКТРИКИ" (из Пакистана?) 😂
похоже на новый мем вроде "БРИТАНСКИЕ УЧЕНЫЕ"
особенно впечатлила пропитка катушек лаком - аплодирую стоя такому лайфхаку
I know. Crazy. It’s like Russian Soldiers haha. A joke
@@Lando_P1 no its not, its true, not a joke:D
Amazing work 👌🏽
Congratulations my dear brother you are the best PEOPLE to build anything . From ECUADOR
Thank you so much 😀
Just great.
While at present I do not speak your language, I can learn! I feel it would be amazing to work with you and learn from you with your hands on approach to technology! Great Job!
Crank
Very Impressive work, nothing compares with hard work.
Yes, thanks.
je suis toujours aussi admiratif de ce travail
Где талант ? Это получается что любой работник добросовестно и исправно исполняющий свои обязанности талантлив ? Тогда получается что например работники автозавода - концентрация талантов ? Ну вы даёте ...
Так и есть.В любом заводе,или производстве есть незаменимыйе люди.Талантливые.Смотри как они собрали трансформатор с простыми дедовскими инструментами.И тепер представ что произайдет, если у них будет технологии 21 _го века?(и между ними не надо завидовать.🙂)
@@talslarnanas1105 Тагда почему же у них их нет, этих самых технологий?
@@talslarnanas1105 Пакистан вообще-то страна, обладающая ядерным оружием. Так что, всё у них есть, пользоваться не хотят.
@@talslarnanas1105 в России так же ремонтируют 😂😂
@@talslarnanas1105 ты хошь сказать шо они импровизировали.без предварительного анализа и без чертежей?
Молодца, настоящее импортозамещение, не сплава 😁👍🔥
Very nice! Good job!
Thanks for the visit.
Wow. Very impressive an skillfull!
Very nice 👍
автор названием ошибся 🤣🤣🤣 это восстановление сильно б\у трансформатора из б\у комплектующих 😂 постройкой это наврядли можно назвать
Новое - это хорошо покрашенное старое!
Очень сильно БУ, что то из годов 70 х
Great job🤩
Not going to lie, that VPI with the rag was impressive 👍
Parabéns muito bom seus trabalhos
Obrigada .
Uno lo que ha aprendido es a enrrollar alambres i no más LOS FELICITO SON UNOS MAGOS DESDE COLOMBIA UN SALUDO 🙏🙏🙏🙏🙏
very nice safety measures very good!👌
Glad you like them!
The flip flops or the lack of masks when doing any work that requires a mask?
Very excellent design for transformers.....😊👍🏾✔
Thank you very much.
It looks like a 20 KV to 380 V oil - cooled transformer.
The way they build it will make it fail after one year, instead of the twenty years normally expected by a static machine.
We phased out oil cooled transformers twenty years ago in favour of ceramic transformers. The old transformers were a safety hazard, as the oil is highly flammable, and the vapours are explosive.
Personally, I prefer properly built oil cooled transformers, as they have a better resistance to transients and peak loads.
PS it is the first time I've seen a petrol powered forklift...
Oil filled transformers are still the normal in the US. Even little 13kv 25kva pole mounts for houses.
@@micah66048 but it's the US nothing surprising here
Vice entendi de eletricidade show de bola
@@micah66048 US has to contend with highly dispersed rural housing, which is an unknown thing here in the UK. US utility companies can't build a substation for each house spaced one mile apart, only to allow the use of a ceramic transformer. So they run a medium voltage (11 - 13 KV) line and use a cheap and rugged oil transformer, placed on the top of a pole, for each house or group of houses...
@@antoniomaglione4101 Or here, underground.
Isso aí é uma restauração. Muito bem feita por sinal.
Estou feliz por ter gostado.
Espectacular! !!!!👌👍💪
cool, so I know the processing of electric transformers, thank you my brother, always success
You are welcome.
Excelente trabajo 👏 saludos
Это обыкновенный капитальный ремонт трансформатора. Причём провод на высоковольтную катушку использовался вторичный. И не показан процесс испытания транса. Как говорят в России просто колхоз.
Русские самые умные, только кроме русских никто об этом не знает, в этом и есть загадка их души.
В россии ещё хуже делают. Эти хоть любят свою работу, а в рашке на от**бись всё.
Oldschool, I like... I'd love a job like this
Enjoyed your video and I gave it a Thumbs Up
Good work 😁😁
Thank you so much 😀
Muito interessante.
Thanks you អរគុណបង👏
I work 26 years in a big factory of big transformers to 400 MVA with 200 tons ,for big electric power sistems .
It was in Roumania and his name was Electroputere Craiova , we work for Fuji , Japan.
Я закончил политех по специальности техника высоких напряжений. Нам привывали трепетное и аккуратное отношение к такому роду техники. Помню на практике шихтовали измерительный трансформатор специальной формы, так зав-кафедры стоял над нами и следил за тем как мы каждую пластину набирали, и с ужасом повторял:," Акуратней, ато будет пожар метала". И мы с дрожащими руками пластинку за пластинкой набирали магнитную систему. Про испытания я вообще молчу, начиная от техники безопасности, заканчивач оформлением результатов и документацией. Или высоковольтный ввод: для некоторых это выглядит как труба, на которую намотан картон и фольга, а для высоковольтников - это система выравнивания электрического поля рассчитаная с учётом краевого эффекта на границе рубашки.
Я это к тому что у мастеров на видео наверное золотые руки, но глубокого понимания того что происходит в технике такого рода скорее всего нету. Как следствие - отношение к тому что они делают. На самом деле это не очень хорошо, потому что результат из разряда и так пойдет затягивает.
Но больше всего насмешил некоторые комментарии типа: импортозамещение в деле. Искренне желаю чтобы в россии импортозамещение проходило именно так)))
Такое работает по счастливой случайности и воли божьей (или кто там у них). Воспроизводимостью, надёжностью, да и просто достижением паспортных характеристик там и не пахнет.
Так в любом деле братец, тут почти как догма, чем больше знаешь тем лучше))
У них перенаселение, потеря не потеря видимо.
Не пожелай другом того, чего не хочешь себе. Впрочем... тебе скоро будет все-равно. А делают они трансформаторы для западных компаний... ПРИКИНЬ?!
@@Rashadrus Прикидываю)))) прикинь
Rebobinamento de trafos. Ótimo trabalho. Eu adoro transformadores. Isso me fez fazer curso de engenharia elétrica, porém, eu nunca trabalhei com isso!
Eu também amo essa parte de equipamentos. Sou engenheiro eletricista também e já trabalhei com trafos e é muito satisfatório ver um trabalho bem feito assim
Isso apareceu na minha timeline agora não consigo mais parar de ver esses videos, é muito interessante e dahora ver como é feito os transformadores e eu que sou um cara que ama eletronica e essas coisas de engenharia então so me faz ficar mais fascinado por essa area.
Fantastic. Just 2 men. Amazing
Glad you enjoyed it!
Really enjoyed watching this
Glad you enjoyed. Stay tuned for more.
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html
Has anyone already noticed the regulatory use of High Security Sandals, with steel toe protectors?
I was about to write about 🤣
Sandals is a common thing in this country..
Or bare hand resin application.
Duh, @@garrettmars756!
He does his nail polishing at the same time!
They used cardboard and wood as insulation for this monstrosity of transformer, do you think they care about safety?
It's fascinating to see what people can build.
Bravo majstori tako se radi
Luar biasa... Infonya sangat menarik mas.... Dukung selalu
*These are postWWII transformers. They suffer from arcing and electric charge leakage and permeativity capacitance functional issues. About time new models are introduced.*
Yea ok sure. Transformers have not changed much over the years. Yes we have some newer types but In most countries the basic steps of making them which they are doing is still used .
These transformers burst regularly and catch fire.
Tudo manual perfeito 👌👏👌👏👏 bons trabalhadores e bom vídeo parabéns
Thank you very much for given the video.
It's my pleasure.
Tremendo laburo
Ничего они не построили. Просто перематывают (восстанавливают) убитые трансы. Хороший бизнесс. Сушилка из контейнера - огонь вообще!
How painful and laborious is to do everything manually.I salute them.
Not that different from the way transformers are made anywhere.
Great work! Greeting from Germany!👍👍👍
Thank you very much!
Parabéns Belo trabalho
Aowsome creation boss. Salute to your team 👍👍👍👍👍👍👍👍👍👍👍
Thank you so much.
Nossa que transformad. Inteligência parabéns.
Good job 👏
Que inteligentes me gusta esa manera artesanal cómo lo hacen i very surprised
Правильно! Сначала всё надо собрать, закрутить, залить масло, покрасить, а потом можно и обмотки прозвонить! Гении, не иначе...
Прозванивают мультиметром или омметром, а здесь уже что-то больше похоже на нагрузочное испытание. Правда, высокая сторона, похоже, так и осталась в воздухе. Да и перекос по току немаленький
@@user-ne5cb5rm3n Если на всех вольтметрах есть какие-то цифры - это значит, что транс прошел испытания!) Перекос, не перекос) Кому это интересно?) Главное, что бы транс напряжение выдавал)))
профессиональный совет
Os caras aí são o bicho! sabe tudo estão de parabéns 🇧🇷 Caucaia-ce 🦕🦖🦖🦕
bosta pura slc
Es genial el acabado de este transformador , desde mi pais podría crear un proyecto para la creación de motores que funcionan con agua
De saber q me pase 12 años de mi vida fabricando transformadores y generadores de alta tensión en mi querido Peru q recuerdos
may i learn about this
Merece respeto persistir en hacer el trabajo que amas durante tanto tiempo.
Os caras são bons. 👍
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html
awesome work! i bet this can push over 1mw with some active cooling! Id just like if you guys had better protective equipment just in case...
Until the fins rust a hole and some water gets inside. Nice fireball...
@@micah66048 to his defence he did paint it and there are paints on the market that combine antirust, base coat and finishing coat in one. On the other side you are probably right and this oils can absorb watter and become conductive
@@dadaselectro4794 that was also a very thin coat of paint and with absolute zero proper pretreatment before coating. its better than leaving it uncoated for sure but wont last ten years
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html
Being pedantic, transformer aren't rated in watts
Bạn làm rất nhanh và chuyên nghiệp rất thích những người có bàn tay như bạn
я таким же способом когда то делал самодельные сварочные аппараты-так же мотал и киперными лентами скреплял катушки.
А у соседей свет моргает, когда таким сварочником варят.
@@TheAAA2012AAA согласен-было такое.
@@user-ie2hh8fi6l
И сейчас встречается!)
В прошлом году видел такой аппарат на шасси от коляски)
Раньше при СССР в каждых электросетях любого города был трансформаторный цех где ремонтировали трансформаторы и перематывали
Сейчас бы точно никто такой трансформатор перематывать бы не стал!
Молодëжи ничего не надо!
Перевели бы подстанцию на инверторные схемы, а трансформатор работавший ещё со времён СССР раздербанили бы на медь!
Привыкли жить хорошо!
Those guys are not Electricians.
They’re factory workers.
Beneath other things, the transformer hast to be evacuated before being filled with oil and the oil has to enter the vessel from the bottom, to enable the remaining air to go to the top.
Grate work
Those exaggerated outer cooling fins shows that there's something you're suspecting/not sure. 😂😂😂
Excellent work though
Why Exaggerated? the are rebuilding Transformers according the standard of that Country! Seen thicker fins but fewer- More Cooling surface.
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html
Animal vidz czcams.com/channels/03GiszvnI_LJemaXUkGczgEyeS.html liner czcams.com/channels/kGslBm84ShaqWiW02rNZRwTechnical.html works czcams.com/channels/UedV2kLGvQprZUv8wCOjFw.html
Amazing Great Work Man
Thanks for the visit.
Fantastic job
Thank you very much!
@@RandomTalent شكرا
Os caras constroem um transformador no peito e na raça 👏👏👏👏👏👏👏
Перебирают старые трансформаторы да и всё. В чем их талант? И с чего вы взяли что они электрики?
@@Konstantin.P. pelo título do video irmão
Nas coxas, isso sim. BR tem un padrão de construção 100x superior.
@@geoge1 VC têm que entender o contexto de vida deles.
Extracting Gold from Store Dust then Making 24K Gold Earrings Part II | 24K Jewels - Gold Smith Jackczcams.com/video/Gjgdz3kzZAw/video.html