Washing, fixing and testing the Husqvarna Rider 16
Vložit
- čas přidán 27. 06. 2020
- !!! Note! Had a viewer call out on me pressure washing the cutting deck, and that is totally right. Husqvarna doesn’t recommend using a pressure washer and neither do I. You push in water in the bearings and ruin them much faster. In this video I was going to change them and do some welding to the cutting deck so wanted it extra clean. I don’t use any water to clean after cutting gras, I only scrape the worst out!!
Did a lot of work to get the Husqvarna rider 16 running as it was supposed to. Was it worth it? You tell me! - Auta a dopravní prostředky
You want to try some Anti Seize on those shafts etc when you assemble them. It works good.
Yeah perhaps, but they are pressed in place so don’t know how much difference it will make when redoing the job 10 years later. It wont hurt I guess? Any brand you recommend?
@@NilsKall Well I am over in New Zealand and I just use what ever we can get over here. I hope to pick up an R 13 very soon and your videos are a great help as well as entertaining. Keep up the good work, Cheers.
16:03 it looks like you have fantasies of ding the TOKYO DRIFT. !!
Do you know what size belt this takes for the outer blades?
Hi! This is the correct belt:
www.rembutiken.se/husqvarna/drivremmar/drivrem-husqvarna-proflex-18-rider-16h-mfl/
After how many years will it be necessary to change the axle and bushing again?
I added a grease fitting to add grease during service. If that is done I don’t think it will have to be changed again.
Vad är det för fjäder man ser hänga ner under klipparen 5:16 in i videon? Min hänger också ner så, kan inte tänka mig att det ska vara så, men har ingen aning om var den ska fästas?
Den är till för att spänna remmen som går till klippdäcket. Ska kolla om jag har en video på var den ska sitta.
Kolla runt 03.46 i den här video. Det är ett metallbleck som sticker ner bakom vänster framhjul och fjädern med dess ”nyckelring” ska sättas fast i denna.
czcams.com/video/ltBGL85oOAE/video.html
Tack så jättemycket för hjälpen! Ska ut och kolla på det imorgon!
Do you have a link to find a bearing housing on a rider 155
Hi, what cutting deck do you have?
Waiting for a return of the Diva your HAUS SNARL. !!
Spoke too soon !! (I always pause and comment)
What is 15.5 hp briggs engine carbuerator number for Rider 16?
You have to use your engine code on Briggs and Strattons homepege to find the correct number. I show how to do it in the beginning of this video: Husqvarna Rider 213 service, English version 4k
czcams.com/video/cRuBEg31nOI/video.html
@@NilsKall 🥺🥺🥺 i don't see number at engine head , because its damaged by rust
@@sagamoress aha! Then It could be harder! Unfortunately I dont have this Rider 16 anymore so can’t check what number it has. What is wrong with the carburetor that is on there now?
Inga probelm att högtryckstvätta rakt på motorn så? 🙂
Nädå, blir rent o fint!
@@NilsKall Grymt. Ska blåsa av min också i veckan o ge den kärlek.
are the gaps of the old and new engines the same? and what are they?
Gaps?
valve clearances. suction and discharge@@NilsKall
@@tadaskabliukas2797intake 0.10 mm, exhaust 0.15 mm. The old engines have side valves so don’t know it is the same clearance.
thanks@@NilsKall
The thumbnail is a real CHEAT .. I see a rider and expect to see some SKIN (swedish type)
Sorry, I didn’t chose that, it was CZcams that put it there automatically. Uploaded during the night so had no control over that. But I will change it, it was meant to be sort of a surprise.
@@NilsKall
And your little "Herring" she appreciates being used as CLICK BAIT ??