Video není dostupné.
Omlouváme se.
How to Install the Tot Lok magnetic cabinet locks
Vložit
- čas přidán 8. 04. 2009
- Michael Hixson of KidSafeInc.com demonstrates how to install and use the Safety 1st Tot Lok Magnetic Cabinet Locks. Baby proof your cabinets with one of the best locks available. Step by step instructions. Distributed by Tubemogul.
Great job. Thank you very much. I bought these two months before my daughter was born. I looked at the directions and said, "No way." My daughter is now 11 months old and starting to open the cabinets. I hopped on CZcams and found this video on how to install. It is perfect. Great demonstration. Thank you. Now I don't have to worry about my daughter drinking all the olive oil!
Honestly, I'm an older new mommy and not very mechanically inclined. The enclosed instructions that came with the hardware were just plain confusing (even with their stupid illustrations). I googled the security system and found this video.
Thank you so much for skipping unnecessary steps and being simple with your instruction. It worked, my curious baby is safe and I'm relieved.
Maybe the ones with "thumbs down " or negative comments learn a different way. I'm more visual and need steps and hands on. By the third one, I had it DOWN pat. Reminder, I'm not mechanically inclined.
User tip: I didn't have a sleeve for my drill bit for the magnet hole so I used a piece of heavy duty tape. It worked like a charm.
Just in case someone reads this MUCH later than the original question... I used this to install the Safety 1st Magnetic Locking System and it's exactly the same - use the template the same way. Great video!
You're a king! The "Step By Step" instructions included in the box are terribly hard to understand. Thanks for your video! Simple and clear!
Thank you so much for the video. I wouldn't have figured it out without you!!
Thanks so much for this video. This helped me a lot as the instructions were not helpful from the manufacturer.
Thanks so much for this, I was hoping there was a video! Thorough and easy to follow!
Thanks for posting this, much easier to understand then the instructions.
So helpful! Thanks a ton, the instructions that came with it were so confusing! I didn't have a 9/32 drill bit and I went to home depot and they didn't have one either. Ended up using a 5/16 and that worked just fine. The drill depth adapter woulding fit so I used packing tape and spent that around the bit at the depth I wanted and that worked pretty well.
I must buy some. I don't have kids as I'm only 14 but I want them 'cause they look fun.
Hello everyone. My name is Ryan. I worked/managed one of the baby-proofing companies in Dallas. We have since retired. I have read lots of the comments below about installation of these tot locks. I believe these are the best locks on the market for cabinets and drawers. As you can see, these are pretty difficult to install l...but they can last a lifetime if installed correctly. These locks are great but are labor intensive. There is no way else around it. However, if you have some woodworking experience, it shouldn't be too bad. Your first lock install will be the hardest. Expect this and you will be relieved later.
Extremely informative. I had no idea that Zack Galifinakis did DIY stuff on CZcams.
Drawers often require customized solutions. Most of my solutions involved using some sort of vibrating tool with a flat blade to remove wood that allows the lock to be placed closer to the face of the drawer (for magnetic purposes). It is amazing what a vibrating tool can do.
This is a wonderful video. Thanks for making it. I would love to see an installation video for installing this product in drawers.
Great Video...clear and simple...I like that. Thanks a lot.
Yay - I installed some succesfully without the template!! So I guess it's not really needed just makes it easier. I did realize though that I left a few of the catches in my old apart. Might you have any extra of those? Regardless thank you for being so helpful!! :-)
I thought this was a great video to show how to install these locks. I'm very proficient with tools even as a SAHM (built a deck, etc, myself), but since you were so great at explaining, I followed your instructions exactly - even though nowhere in the instructions does it say to drill pilot holes for the 1/2" screws. I never drill pilot holes (to my detriment many times), but since I need to get into the habit of doing it, I did - just as you show here in your video. So, I used the 1/8th inch drill bit, drilled all my holes, went to put in the hardware and... THE SCREWS THAT COME WITH IT ARE NOT 1/8TH SCREWS. They are WAY thinner than that! Now I have to go to the hardware store and get all bigger screws because the pilot holes are way too wide for the screws they provide. Another issue I have other than never drilling pilot holes is taking people's word at face value instead of checking for myself, first. So, thank you for teaching me a few valuable lessons. I like the professionalism in the video itself, but perhaps update it to include the info that you either need a smaller drill bit or none at all for the 1/2" screws. Not happy but lesson learned.
FYI: The #8 screws I had to get to fix this error are TOO LARGE for the openings in the hardware. You have now wasted $40 and a lot of time and effort for me. Now I have to go and spend more money on an alternative because I'm not drilling my cabinets full of holes.
Pay attention to the above comment about the 1/8th drill bit - you really need to go with something smaller like 3/32 or 5/64 (I used 5/64). Its really annoying to get the pilot holes done and fine out they are too big!
Robert M Hoehn yeah an 8th inch drill bit is just about a clear hole for those tiny screws. 3/32 all the way. i keep an 1/8 and a 3/32 on my drill for pilot holes all the time, but the 1/8 is for bigger hardware like storm door screws, some big construction/drywall screws, etc
+Robert M Hoehn are pilot holes needed or can you shoot the screws straight into the template?
This video is very well done. Of course everyone has different ways of doing things and every technique can be improved upon. I welcome people's comments as hopefully people will learn from my contribution and vice-versa. And don't get frustrated. When in doubt, hire a professional.
Good info. Although for future videos, you might consider using a lavaliere microphone so we can hear you better. You're getting lost in the echo of the kitchen, and I can't hear you so well unless I wear headphones.
The tips below probably go above and beyond what most people would do when installing these locks. However, I installed 1000's of these locks and these are some tips from my experience. Warning. Some of you will think this is overkill. I would rather give you too much info than not enough.
Did anyone else notice the drill is in reverse while he's drilling holes?
yes lol
+Bryant .Collins - It just seems that way but, if look closely it really is turning clockwise
+myutube1960 no its not. its drilling on reverse. check it out 2:34
lol... yes it really is in reverse.
you drill in reverse to avoid wood tear out just fyi
These locks aren't usually available in the big box stores because they aren't as profitable as most of their cheap plastic alternatives. A google search will yield cheap providers (amazon). Also, I don't like adhesive locks as the can fail (although unlikely), due to humidity (the catch can fall off) or adult strength being applied. These locks are quality. If you get a dud, they can be returned for replacement.
Awesome Video! Thanks!
Do have a question: What is the difference between the Safety 1st Magnetic Locking System 9-Piece Set (HS13) and these Tot Lok's?
Is there any place to order the catch and the templates? I just got like 50 of these from a garage sale, but there's no catches or templates. Realized that you need the catches today after putting on of them on a drawer lol
Clear paper reinforcements would work better than a pencil to mark the location of the lock. Also, always try to install as close as possible to the handles so the cabinet can be opened with one hand only.
I just moved & took my old locks w/ me. I don't have the template for where to drill to make sure the lock & catch line up :-( Any suggestions? Kinda under house arrest until I get these installed.
Could it be use for a cabinet door that opens up...
I would recommend wearing safety glasses if you are laying on your back drilling above your face like that. Safety first right?
ty 4 showing me where 2 screw. lol
Is pre-drilling necessary or can you shoot the screws straight into the template?
+ARSONPINNACLE YMMV some cabinets are just particle board which tends to self-destruct without pilot holes. Even real wood can possibly split with any screws but the tiniest. Also you have to at least drill for the magnet release.
why is your drill going in reverse
A few tips for the DIY's..
Take your time when installing these. These are NOT a quick projects. I watched this video which was 6 and a half minutes. In reality, these take about 15 minutes each to install. Sometimes, it took more time when there was a customized solution involved, and even longer on drawers. Get a small flashlight and inspect the holes to make sure you have done what you intended to do. When you look at your work area you can see/predict what will work. (ex. am i too close to a cabinet seam? or is there damage that doesn't make this spot a good installation spot? .....or is there is other cabinet hardware in the way...you don't want to drill and it not be a suitable solution (common sense). I have seen people install other products to lock the drawer, get done, think they have done a good job, and couldn't shut the door because the garbage disposal or bottom of the sink got in the way. these locks are small and that probably won't happen...but still, look before you drill! This goes for any project.
Just wanted to point out, use safety glasses, and even gloves while using a drill to protect yourself from accidents. In addition, use a proper sized screw bit that is not too big/small for the screw and maintain adequate pressure on the drill while screwing them in, this will reduce stripping the screws while screwing them in.
@mrbasicshark correction HS133
yout drill is in reverse!! ha ha
^obviously, doesnt have small children.....