Something worth noting after initial setup. In my experiences, setting the EPA to 50% before plugging in servos can save the servos, especially the little Chineasium mini's IF they decide to go full send in either direction. Great vijaeo👍👍
Thanks for the tips. I have a few of these radios, 1 I use, and 2 others I got on sale, as spares. I like them. And you can't beat the price of the receivers, especially compared to other manufacturers. Also, having 6 channels is nice if you want to control things like lights on or off etc. etc.
@@rclunatic I don’t drag race. I never was able to do speed runs like I wanted. Anyplace I can is too far. Plus since May I haven’t been able to be active. I’ll be back though. The remote is amazing. Tons of features. Easy to use and setup. And the range is 1900 feet in one direction. So for speed runs it’s a good buy. Less than 100$ as well. Can’t go wrong. Tomleyrc has some awesome videos showing it’s capabilities. Cheers.
I took out a buggy that I just finished building, I noticed I needed to adjust the steering end points because it was flexing the servo in it's mount at a full turn. Could not remember how to do that on my RC6GS, but I remembered this video and you covered it! thanks!
Just got my first transmitter. This answered a lot of questions about the setup even though I have a Radiolink AT9S a lot of the concepts seem to be the same across most models. Great video. I'm trying to setup a tank crawler and having a really hard time with the configuration. I think it's because my stick mode is different than how I want to use the sticks. :/ Next youtube search is for stick modes.
Awesome info & very straight forward!! Just the info I was looking for. I have been using this controller for ~2yrs & wasn't sure about the steering & throttle exp settings. I do speedruns & I needed my speed sensitivity for the steering really low. I have been using endpoint settings to reduce the travel & speed of the servo. But it's a pain cuz it's hard to turn the car around at the starting & ending points of the run. I would have to increase the steering travel endpoints to turn the car around & decrease it for the run. Because at 120+mph, you do NOT want to pull that steering hard & too far in either direction lol..... Bad things happen 😄 For the throttle, I had been using the punch control on the Castle ESCs. I will have to see how it works out for speedrun setups, cuz these cars will literally spinout out of control when taking off at just a hair tap of the throttle. Thanks again for sharing 😎 👍
So with the throttle expo setting for example, I could adjust the settings if the truck is lifting the front end too much on take off, correct? Currently my son just grabs full trigger since he hasn't mastered modulating the throttle yet. I love the jackstands you have your trucks sitting on in the background! Very cool!
I use many of those settings on the eight vehicles I have bound to my Radiolink RC6GS V2. I find steering expo to be the most useful, especially on vehicles I use primarily for straight line runs. With expo set at around -30, it's easier to keep the vehicles straight and not have the vehicle veer quickly at high speed. I find setting servo endpoints is easier with this radio than on other radios I own or have owned.
Thank you so much for all that great information I just received my radio link for channel receiver controller. It’s gonna take a little time but I’ll get used to it it already performs a whole lot better than the Spektrum STX2. 😆
I know you can ch mix for 4w steering, but is there away of of mixing a toggle switch in so you can turn it off , crab steer and normal 4w steer , Like you can with other tx,s
thanks for this 317 RC put me onto this video as I needed the Steering EXPO help big time! Watch out for me putting your tips into action on the 8s Traxxas Rally this weekend!
Hi, I would like to ask for your help if it is possible: I have this radio model but (I don't know how) the "beep" of when the radio is turned on and the "beep" of the keys is gone Can you tell me how to restore the sound ?? P. S. I also tried to reset the radio and remove the batteries, without getting anything. Thanks a lot if you can help me !!
@@ExocagedRC Thanks for putting me away, I contacted the official Facebook page and now I'm waiting for an answer because I didn't understand what happened. Thanks a lot again!
I’m using this radio and receiver on my limitless, which I use for drag racing, I’m having a hard time to get the steering straight! Can you please help me
Exocaged RC savox sc1258! I tried turning it down epa 90% stexp-54 stspd: turn 50% return 75% gyro on std 7% rate! Off the line for drag racing, can’t figure it out! It goes side ways instead of straight no matter what I try
CAN YOU HELP ME OUT?… RG6&xlx2 my Kraton wants to act like it’s in rock crawl mode or something. Motor wants to copy throttle so tightly that it will not coast down hill if there’s ANY throttle input at all, it won’t want to roll faster than what the throttle input allows. It rolls perfectly free in neutral yes it does but, if I’m doing 10-20-30-40 mph, I have to let off the throttle iMMEDIATELY if I want the truck to coast freely and not “jerk” and stumble because it wants to copy the throttle command even if it’s returning back to neutral. No aux wire, no modes assigned to it neither. It’s got to be something with the transmitter.🤷♂️ help plz thanks.
@@ExocagedRC …. So what’s the fix?¿ I haven’t heard of other ppl with xl2’s talking about this problem and many ppl do speed runs with xlx2. It would be doom’s day for speed runners bcs there’s no way to avoid the motors behavior.. please tell me you know SOMETHING LOL 🤷♂️
@@ExocagedRC ….. since your so well known and respected, would you consider doing a short video on the subject or live chat to see what the rc community knows about this? Btw man thank you for entertaining the topic with me I love your Chanel Rock on💪
![Eminem - Houdini [Official Music Video]](http://i.ytimg.com/vi/22tVWwmTie8/mqdefault.jpg)
You are kick ass man. Not many explain things so easily and concisely as you. I learn tons from your channel
Awesome buddy. Glad I could help!
Something worth noting after initial setup. In my experiences, setting the EPA to 50% before plugging in servos can save the servos, especially the little Chineasium mini's IF they decide to go full send in either direction.
Great vijaeo👍👍
Great short but sweet video..thank you
Thanks for the tips. I have a few of these radios, 1 I use, and 2 others I got on sale, as spares. I like them. And you can't beat the price of the receivers, especially compared to other manufacturers. Also, having 6 channels is nice if you want to control things like lights on or off etc. etc.
Yes, the receiver gyro is good for my drifting car
Just purchase this radio for my limitless. Nice explanation on the features. Thank you!
Do you drag race with the limitless or speed runs? And do you like this transmitter to go with the limitless?
@@rclunatic I don’t drag race. I never was able to do speed runs like I wanted. Anyplace I can is too far. Plus since May I haven’t been able to be active. I’ll be back though. The remote is amazing. Tons of features. Easy to use and setup. And the range is 1900 feet in one direction. So for speed runs it’s a good buy. Less than 100$ as well. Can’t go wrong. Tomleyrc has some awesome videos showing it’s capabilities. Cheers.
I took out a buggy that I just finished building, I noticed I needed to adjust the steering end points because it was flexing the servo in it's mount at a full turn. Could not remember how to do that on my RC6GS, but I remembered this video and you covered it! thanks!
awesome man!
Ur a life saver I was going bonkers trying to reverse my throttle lol
Great video, man. Very much appreciated.
such a straight forward video and really helpful with menu settings. Thanks so much bud got my rc4gs all dialed in
Thank you so much. Super helpful video 👍
Man this really helped me out in my new nitro engine. She is throttle sensitive and I needed it to slow it down.
Thanx this video helped fix my steering and throttle
Thanks for your upload mate 👍
Another Great Instruction Video Brother Very useful information on the Radiolink RC6GS 😎👍👍
thank you for the tips sir! it will help alot with my fast tamiya tt02, ill be able to trim sensivity and trims easly!
! thank yooouuuu
Just got my first transmitter. This answered a lot of questions about the setup even though I have a Radiolink AT9S a lot of the concepts seem to be the same across most models. Great video. I'm trying to setup a tank crawler and having a really hard time with the configuration. I think it's because my stick mode is different than how I want to use the sticks. :/ Next youtube search is for stick modes.
Nice review sir thank you.. Always support your channel 😆😆👍👍
Really helpful vid, thanks!
Awesome info & very straight forward!! Just the info I was looking for. I have been using this controller for ~2yrs & wasn't sure about the steering & throttle exp settings. I do speedruns & I needed my speed sensitivity for the steering really low. I have been using endpoint settings to reduce the travel & speed of the servo. But it's a pain cuz it's hard to turn the car around at the starting & ending points of the run. I would have to increase the steering travel endpoints to turn the car around & decrease it for the run. Because at 120+mph, you do NOT want to pull that steering hard & too far in either direction lol..... Bad things happen 😄
For the throttle, I had been using the punch control on the Castle ESCs. I will have to see how it works out for speedrun setups, cuz these cars will literally spinout out of control when taking off at just a hair tap of the throttle.
Thanks again for sharing 😎 👍
So with the throttle expo setting for example, I could adjust the settings if the truck is lifting the front end too much on take off, correct? Currently my son just grabs full trigger since he hasn't mastered modulating the throttle yet.
I love the jackstands you have your trucks sitting on in the background! Very cool!
Even though I only got 4 channel version I was stuck on steering trim thanks for help
Thank you!
You are my savior
I use many of those settings on the eight vehicles I have bound to my Radiolink RC6GS V2. I find steering expo to be the most useful, especially on vehicles I use primarily for straight line runs. With expo set at around -30, it's easier to keep the vehicles straight and not have the vehicle veer quickly at high speed. I find setting servo endpoints is easier with this radio than on other radios I own or have owned.
Some might understand what Expo means easier if they knew what it stood for; the mathematical function Exponential.
Nice video man
Thank you so much for all that great information I just received my radio link for channel receiver controller. It’s gonna take a little time but I’ll get used to it it already performs a whole lot better than the Spektrum STX2. 😆
oh yeah heck almost anything is better than that
Good video thanks
Good vedio so helping me tq so much sir 😁😁😁❤️❤️❤️
The reverse 🔄 PART HELPED FOR RADIOLINK 7…MSG HOBBIES & high quality gaming!!
Aye guys God bless love what your doing I just bought it and I wanna is there a chance it gives u temp
Thanks for the tips, helped me out alot. One quick question, the voltage displayed on the screen, is it for the transmitter or vehicle voltage?
johno425 that’s the transmitter voltage
I planning buy one these. Question. This radio has countdown timer? I will use on buggy race and need this timer to alert when I need goto pit.
Thank you Joe for this video it helped me alot. Can you tell me how to adjust the braking?
That’s probably limited by your esc. You may need to adjust that there
@@ExocagedRC yeah I had a brain fart but thanks for replying. I remembered right after I sent you a message
Any idea on how to add/remove brake strength on this radio? What menu? Thanks!
I know you can ch mix for 4w steering, but is there away of of mixing a toggle switch in so you can turn it off , crab steer and normal 4w steer ,
Like you can with other tx,s
Is there a way to control steering dual rate with one of the switches?
thanks for this 317 RC put me onto this video as I needed the Steering EXPO help big time! Watch out for me putting your tips into action on the 8s Traxxas Rally this weekend!
Awesome man glad I could help. 8s Traxxas Rally sounds cool.
How do you slow down reverse to make it less jumpy and smoother? Cheers.
Is it possible to assign speed change to VR dial? Also, is there a way to make the lights that I installed to turn in and off?
If i get a second reciever box for a different vehicle will it unbind the first reciever?
No, just use a different model on the radio
I need info on how to set ABS. Right now with ABS off, car stops on a dime without lockup. It seems I don’t need ABS.
Can the VR knob be setup to change the throttle rate? By that I mean I can change the max speed with this knob?
I think it can, I've never tried for that.
I'm an issue. Why does the acceleration lag by about 3 seconds after going in reverse?
Life saver
Hi, I would like to ask for your help if it is possible: I have this radio model but (I don't know how) the "beep" of when the radio is turned on and the "beep" of the keys is gone Can you tell me how to restore the sound ?? P. S. I also tried to reset the radio and remove the batteries, without getting anything. Thanks a lot if you can help me !!
Hmm. I haven’t messed with that. Is it in the menu? If not, it’s possible that tiny little beep speaker is messed up.
@@ExocagedRC Thanks for putting me away, I contacted the official Facebook page and now I'm waiting for an answer because I didn't understand what happened. Thanks a lot again!
my question is what are you all doing with the second antenna on the reviever?
its either coiled up in the box or I run it out next to the one in the tube
Run them out the body in a v
Have you looked at ID seed function with new firmware upgrade,
I haven’t messed with that yet. Sorry
CAN I USE THİS ON DRİFT CAR? this remote control can controlled ?
You run a lipo in your RC6GS ? What ist your longest runtime with the Radio?
I ordered a 1500mah 2s lipo for My RC4GS... You can from 4.8v to 15v i think ( says on the transmitir behind the batteries)
I heard that a 300mah battery would last like 2-3 hours
How do I get the reverse and forward correct it I. Reverse only this minute
I’m using this radio and receiver on my limitless, which I use for drag racing, I’m having a hard time to get the steering straight! Can you please help me
Steering should hold straight once it’s set. The gyro will make very fast adjustments as needed. What servo are you using?
Exocaged RC savox sc1258! I tried turning it down epa 90% stexp-54 stspd: turn 50% return 75% gyro on std 7% rate! Off the line for drag racing, can’t figure it out! It goes side ways instead of straight no matter what I try
@@MrJojowalks ever get this figured out?
@@marquisraps660 I went with futuba bro
It give you everything else
It has the dual-rate option, but there's no button, and you can't assign any button to control it.
CAN YOU HELP ME OUT?… RG6&xlx2 my Kraton wants to act like it’s in rock crawl mode or something. Motor wants to copy throttle so tightly that it will not coast down hill if there’s ANY throttle input at all, it won’t want to roll faster than what the throttle input allows. It rolls perfectly free in neutral yes it does but, if I’m doing 10-20-30-40 mph, I have to let off the throttle iMMEDIATELY if I want the truck to coast freely and not “jerk” and stumble because it wants to copy the throttle command even if it’s returning back to neutral. No aux wire, no modes assigned to it neither. It’s got to be something with the transmitter.🤷♂️ help plz thanks.
It’s not the transmitter. It’s in the firmware of the esc. My xlx2’s do this as well.
@@ExocagedRC …. So what’s the fix?¿ I haven’t heard of other ppl with xl2’s talking about this problem and many ppl do speed runs with xlx2. It would be doom’s day for speed runners bcs there’s no way to avoid the motors behavior.. please tell me you know SOMETHING LOL 🤷♂️
@@ExocagedRC ….. since your so well known and respected, would you consider doing a short video on the subject or live chat to see what the rc community knows about this? Btw man thank you for entertaining the topic with me I love your Chanel Rock on💪
Does anyone know how and if it is possible to set EXPO on off on a switch
How do I activate the RadioLink RC6GS v3 failsafe because when I turn off the radio the cart accelerates by itself?
Not sure to be honest.
Turn vehicle Off FIRST ! Always !!
How do i setup failsafe
great question and I just don't have an answer for you
My Sumter ring is stuck in reverse