This is exactly what I'm doing - Water Pump, Timing belt, tensioner and idler pully... Except My motor blew up so Im doing it to a 112k mile replacement motor on a stand before I drop it in! Also doing axles, radiator, hoses, thermostat, starter, alternator... I dont want any issues for 5 + years!
🔧BUY Timing Belt Kit (Includes water pump): amzn.to/3xZSBYx Subscribe to our channel: czcams.com/users/homeownerrepair FIND THE INFO YOU NEED! 00:00 Introduction 01:08 Drain Radiator 01:42 Alternator Belt Removal 07:51 Loosen Alternator 09:57 Remove Timing Belt Cover 12:00 Timing Belt and Water Pump Kit 13:49 Timing Belt Alignment Explained 15:51 Timing Belt Removal 19:32 Timing Belt Tensioner Removal 20:38 Water Pump Removal 22:07 Water Pump Reinstallation 26:16 Timing Belt Tensioner Reinstallation 29:11 Reinstall Timing Belt 34:38 Reassembly
I'm about to perform this timing g jib on my mom's car, found the kit a few bucks cheaper on rockauto. But same good quality kit. Thank you for the video I feel confident now that yoy explained the marks amd how to get them lined up.
Good vid. Doing this exact job right now. My OCD forces me to point out that that is not an oil slinger. It's a dust cover. haha With a new spring, I suppose you can trust it to self tension the t belt. Mine didn't come with a new one, so I manually tightened it. The spring was too tired to trust. I very much prefer the older style of self tensioners, but installation required a long bolt tool to preload. Without it, the belt WILL jump.
Appreciate your detailed video. Thank you. I compiled a step-by-step instruction sheet for our 2009 Accent. My impact wrench could not remove the 22mm crank bolt; had to get a pulley holder tool. The teeth on the timing belt were dry-rotted and fell off, then the crank gear spun. Arizona summers did not help. As you know, engine is interference. Lucked out. Engine started instantly, idled fine and runs good. Dodged that bullet.
My belt is at 93k & the stress is real driving it. Eevry time I start the car to go anywhere, The thoughts enter my mind .........this may be my last drive in this car. Plan on doing this job in 2 weeks, In the mean time I want a complete List of EVERY tool needed to do the job. nearly impossible to actually get that info. even in the Hyundai accent FB group, one guy said I need an 8mm a 12mm & a 17mm 🤣
the second I got everything locked down & lined up with the new belt done, Id wanna start it for 5 seconds , then continue putting the little stuff back.
@@HomeOwnerRepair, I understand that, but I’m learning the hard way, so my mechanic friend doesn’t want me to mess with the timing. I’m trying to replace the water pump. Is it possible to remove it without messing with the timing belt?
Do you have any info on getting the tensioner off the AC belt? I thought it was just like the tensioner on the alternator and I would be able to just loosen the bolt but it doesn’t appear to be. Trying to put a new compressor on and need to get that belt off. Thank you in advance.
Hey! I have an '11 GLS, died on the road, Timing Belt was destroyed. Changed the timing belt, made sure the cam and crank were tdc, changed the coils, and the cam sensor but I have no spark. Engine turns over and cam does too. I'm going to check the voltage with a multimeter on each coil but when I checked it out of the chamber it sparked after turning over a few times. After I was going to take the valve cover off to check if the valves are engaging before I remove the head. Help?
How’d you get the crankshaft bolt off without messing up the timing? Cause i see it cut and jumped fast forward. Can i just use a impact to get it off?
One of the best instructional videos I've watched on CZcams. Thankyou for sharing.
Thank you for watching our auto repair video that shows you how to replace the timing belt on a Hyundai Accent. Hope it helped you out.!
This is exactly what I'm doing - Water Pump, Timing belt, tensioner and idler pully... Except My motor blew up so Im doing it to a 112k mile replacement motor on a stand before I drop it in! Also doing axles, radiator, hoses, thermostat, starter, alternator... I dont want any issues for 5 + years!
Thank you so much for this video! It was very informative
Glad it was helpful!
🔧BUY Timing Belt Kit (Includes water pump): amzn.to/3xZSBYx
Subscribe to our channel: czcams.com/users/homeownerrepair
FIND THE INFO YOU NEED!
00:00 Introduction
01:08 Drain Radiator
01:42 Alternator Belt Removal
07:51 Loosen Alternator
09:57 Remove Timing Belt Cover
12:00 Timing Belt and Water Pump Kit
13:49 Timing Belt Alignment Explained
15:51 Timing Belt Removal
19:32 Timing Belt Tensioner Removal
20:38 Water Pump Removal
22:07 Water Pump Reinstallation
26:16 Timing Belt Tensioner Reinstallation
29:11 Reinstall Timing Belt
34:38 Reassembly
I'm about to perform this timing g jib on my mom's car, found the kit a few bucks cheaper on rockauto. But same good quality kit. Thank you for the video I feel confident now that yoy explained the marks amd how to get them lined up.
Good vid. Doing this exact job right now.
My OCD forces me to point out that that is not an oil slinger.
It's a dust cover. haha
With a new spring, I suppose you can trust it to self tension the t belt. Mine didn't come with a new one, so I manually tightened it. The spring was too tired to trust. I very much prefer the older style of self tensioners, but installation required a long bolt tool to preload. Without it, the belt WILL jump.
Thanks for watching. Hope the video helps you out.
Appreciate your detailed video. Thank you.
I compiled a step-by-step instruction sheet for our 2009 Accent.
My impact wrench could not remove the 22mm crank bolt; had to get a pulley holder tool.
The teeth on the timing belt were dry-rotted and fell off, then the crank gear spun. Arizona summers did not help.
As you know, engine is interference. Lucked out. Engine started instantly, idled fine and runs good. Dodged that bullet.
Thanks great! Yeah, if this timing belts snaps it can implode the engine.
with all the simplicity i still love that car.
engine reliability can be upped though
It's a pretty good little car.
Nice video thanks for taking the time to do it.
Thanks for watching!
Thank you for making this video
Glad it was helpful!
My belt is at 93k & the stress is real driving it. Eevry time I start the car to go anywhere, The thoughts enter my mind .........this may be my last drive in this car. Plan on doing this job in 2 weeks, In the mean time I want a complete List of EVERY tool needed to do the job. nearly impossible to actually get that info. even in the Hyundai accent FB group, one guy said I need an 8mm a 12mm & a 17mm 🤣
Im confused? I have a 2009 accent and the engine cover has DOHC 16V on it.
its a 1.6 but im only seeing 1cam on this car
the second I got everything locked down & lined up with the new belt done, Id wanna start it for 5 seconds , then continue putting the little stuff back.
Good day, does anyone know if you have to mess with the Timing Belt to remove the Water Pump?
If the timing belt has over 60,000 miles on it I would replace it while you are in there.
@@HomeOwnerRepair, I understand that, but I’m learning the hard way, so my mechanic friend doesn’t want me to mess with the timing.
I’m trying to replace the water pump. Is it possible to remove it without messing with the timing belt?
Do you have any info on getting the tensioner off the AC belt? I thought it was just like the tensioner on the alternator and I would be able to just loosen the bolt but it doesn’t appear to be. Trying to put a new compressor on and need to get that belt off. Thank you in advance.
I currently do not this car did not have AC in it.
Hey! I have an '11 GLS, died on the road, Timing Belt was destroyed. Changed the timing belt, made sure the cam and crank were tdc, changed the coils, and the cam sensor but I have no spark. Engine turns over and cam does too. I'm going to check the voltage with a multimeter on each coil but when I checked it out of the chamber it sparked after turning over a few times. After I was going to take the valve cover off to check if the valves are engaging before I remove the head. Help?
Sorry just saw this question.
How’d you get the crankshaft bolt off without messing up the timing? Cause i see it cut and jumped fast forward.
Can i just use a impact to get it off?
We may have used an impact to get it off.
How has this car held up? Do you enjoy it?
It has held up great! It also gets great gas mileage and I have enjoyed it
Are both of the pulleys considered the water pump pulley?
Yeah, there are two different pullies on that water pump.
How do you know if the crank sensor is bad
It was throwing a code
I had this problem, your car will stall and other fun things !
The crank pulley moves out of place every time i try to get the belt on 😵💫
There might be a bolt your are missing that needs to me tightened.
@@HomeOwnerRepair the tension is taken off when installing the belt no?
👏👏👏👏👏
Hope this helped you out.
So probably should let my mechanic do this instead of attempting by myself to save a few hundred bucks? :p
It's not a cheap job. I think I was quoted about 700 for it?
It's not too hard to do just takes a little time.