The reverse gear requires that an idler gear be slid to mesh with the regular gears. Quite often the shift linkage has fallen off inside the transmission, it’s sometimes and easy thing to fix through the top linkage hole. That's what he did.
This Gearbox belongs a Mitsubishi same thing happened to me but instead of removing the sensor I removed the valve body never remove the top bolt because the brake band falls out of place and wont engage reverse
The plug he pulled was from the band jumping off the band dial/ plug.he just pulled the band back and reinstalled the plug/dowel that holds the band.but he still has to correct the issue that caused the band to jump off in the first place.it could have been low on fluid or the band wore.he could put a longer service in to take up the slack or well to it to patch it up.
People undo the brake band restraining bolt thinking its an oil drain plug. A common mistake on old freelander jatco autos, no reason why it wouldn't be repeated elsewhere. This vid showed how how to easily reseat the brake band and set it, otherwise a needlessly laborious job.
My pajero won't revers but it go forwad smothly .. i went to many transmission specialists and they said , i must change the transmition wich is cost toooo much .. i did not flow there recommendation ... what i did to fix it is : i went under the pajero and open every wire contractor on the transmition and spray electric cleaner on them for cleaning .. also spray the wires connect to transmition computer And let it dry .. after that transmission worked fine .. now after one year i have no problem with reverse or forward
Do u mean u spray all plugs about transmion by using contact cleaner ? Because i have problem in versa nissan CVT .. delay about 10seconds befor starting go revers
@@mooma20121 doing what that guy is saying will destroy any transmission. Electric/electronics only controls shifts, NOT foward (1st. Drive) or reverse. Drive and reverse are mechanic/hydraulic controlled. You have to open the transmission and change the reverse band with a new one.
What it looks like he's doing is removing the Brake Band Retaining Bolt and moving the band over to either the correct position, with the wire, OR moving the brake band to another position that's tighter and then reattaching the brake band anchor/retaining/whatever bolt. I don't know which brake band it is back there. There may only be one for that car. But, my guess it that it will make a worn out band pull tighter and overcome slipping. Which isn't really a good thing because it will eat away the drum. But, then again the drum is pretty thick, so. Whatever.
Bad reverses usually have a bad sealing ring or bad o'ring in the reverse drum piston or some other lack of pressure problem that disables the reverse drum from compressing. Reverse drums and gears are usually in the front part of the trans and are the first ones just behind the pump that unbolts first. What he did could even just lock up the overdrive or something to make the other gears engage somehow, but he's definitely messing with a band anchor bolt.
Hi, i have a 2004 ford e350 with a transmission issue.5.4L engine an. 4R75w trans I think. Sometimes when i put reverse the engine shutdown,unless I press the brake and the gas at the same time to maintain the engine on, to can going in reverse. If you have some suggestions please let me know. Thanks a lot.
This was the exact problem I had...if I hadn't seen this vid I would have never worked it out...shogun 2006 3.2...just enough room under there to fix this issue
Esto me paso en una Montero quite el tornillo pensando que era un tapon de llenado (un error muy comun) pero no lo es, eso es el que tornillo que aprieta la banda de freno si esa se suelta la reversa no entra lo que hizo aqui el chico fue de alinearla con el agujero y volver a poner el tornillo 🔩 si no habria que destapar la caja y ponerlo en su sitio
I recently acquired a 2005 Ford Focus start up put it in gear won't move none of the gears are engaging I hear these transmission are notorious for going out is it bad or is it something....IDK😕
after attaching back the automatic gearbox to lexus v8 engine the engine starts correctly but the gearbox cannot select gears how can i put the gears back so i can drive
Hi All, I have lexus LS 430 2002 not engaging into reverse at all,while in forward its smooth.went to workshop they told there is codes of valve body.any one can help what to do?
what kind of vehicle ? It is a rear wheel drive ... no need for talk see what he is /has done but what caused the inner part to slip to start with... is it made to do so under certain conditions ?
good vid. i am having the same issue i can't switch to reverse gear. everything is good n smooth. could it be the reverse switch too? did you solve the problem?
@@zeus-io3hn Sir, when I checked her with a mechanic, her non swift cable is broken and she is showing the mark on the four wheel drive [4 × 4 L]. Tell me a solution for this. Even after turning off the four wheel drive, that is not happening.
I don't have a clue what type transmission this is or really even what you were doing. But I have a 1999 Chevy 1500 pickup truck v6. And I seen a similar video once truck had no reverse and this was the fix. Don't know what this is the same fix for the same situation. But it's definitely not the same video I saw about a year ago don't have a clue what he is doing or on what type transmission
@@fast68chevy this is information that should be given at the beginning not at the end. Not even in the bed itself. You are saying at the end of the video it was stated who is going to set watch your entire video to see if it applies to their vehicle nonsense
@@jeremiahfisher6994 I'm a Puerto Rican, and Puerto Rico is a USA territory so I'm born USA citizen. The thing is we speak spanish. What I'm trying to say is that USA it's not just people that speak english, maybe he is illegal, maybe he is more American than you, who knows. But I know one thing for sure, in car mechanics, he is a dumb with passport or without it.
My 2011 jeep feel weak in reverse. My driveway has a slight hill. When i back up it it feel like something is bent a little. Anyone have any thoughts.tia.
Nice video, it pulled up while searching for a solution on my question for a 2014 BMW 135i 6 speed manual transmission that will not into reverse gear, any chance this will work on this problem?
Eddie Kane nope! You will not find a silver bullet fix like that on CZcams. This was not even a fix just a temporary repair until it jumps of the dowl again. It jumped out of place for a reason and it was not addressed take it to a mechanic
Why did you even bother posting this you don't say anything you don't say what transmission is it is you don't say what the problem is you don't say what the solution is
I feel after watching this, I can finally become a certified transmission mechanic. I just needed to learn the word "ok". 😂
At least you could have said what kind of transmission you're working on
Right!!!
We need more people like you educating and informing thank you for being brief and to the point
This is one of the few projects where you are successful is if the project goes backwards.
The reverse gear requires that an idler gear be slid to mesh with the regular gears. Quite often the shift linkage has fallen off inside the transmission, it’s sometimes and easy thing to fix through the top linkage hole. That's what he did.
for what transmision is that for a titan
Ok..which car??
The million dollar question because im looking at gm videos and this came up
No introduction, just right into it I love it. This man doesn't have time for that 😆🤙
This Gearbox belongs a Mitsubishi same thing happened to me but instead of removing the sensor I removed the valve body never remove the top bolt because the brake band falls out of place and wont engage reverse
perfectamente bien explicado!!! marca de carro numero de transmission,problema que tenia en fin todo todo!!!
The plug he pulled was from the band jumping off the band dial/ plug.he just pulled the band back and reinstalled the plug/dowel that holds the band.but he still has to correct the issue that caused the band to jump off in the first place.it could have been low on fluid or the band wore.he could put a longer service in to take up the slack or well to it to patch it up.
People undo the brake band restraining bolt thinking its an oil drain plug. A common mistake on old freelander jatco autos, no reason why it wouldn't be repeated elsewhere. This vid showed how how to easily reseat the brake band and set it, otherwise a needlessly laborious job.
Just swell, thanks for explaining this procedure verbally in full detail!!! Couldn't have asked for a more detailed video!🙄
I'm 39 seconds in I guess I'll learn nothing
@@jeremiahfisher6994 WTG! Join the crowd!
My pajero won't revers but it go forwad smothly .. i went to many transmission specialists and they said , i must change the transmition wich is cost toooo much .. i did not flow there recommendation ... what i did to fix it is : i went under the pajero and open every wire contractor on the transmition and spray electric cleaner on them for cleaning .. also spray the wires connect to transmition computer And let it dry .. after that transmission worked fine .. now after one year i have no problem with reverse or forward
Do u mean u spray all plugs about transmion by using contact cleaner ? Because i have problem in versa nissan CVT .. delay about 10seconds befor starting go revers
@@mooma20121 doing what that guy is saying will destroy any transmission. Electric/electronics only controls shifts, NOT foward (1st. Drive) or reverse. Drive and reverse are mechanic/hydraulic controlled. You have to open the transmission and change the reverse band with a new one.
What it looks like he's doing is removing the Brake Band Retaining Bolt and moving the band over to either the correct position, with the wire, OR moving the brake band to another position that's tighter and then reattaching the brake band anchor/retaining/whatever bolt. I don't know which brake band it is back there. There may only be one for that car. But, my guess it that it will make a worn out band pull tighter and overcome slipping. Which isn't really a good thing because it will eat away the drum. But, then again the drum is pretty thick, so. Whatever.
Bad reverses usually have a bad sealing ring or bad o'ring in the reverse drum piston or some other lack of pressure problem that disables the reverse drum from compressing. Reverse drums and gears are usually in the front part of the trans and are the first ones just behind the pump that unbolts first. What he did could even just lock up the overdrive or something to make the other gears engage somehow, but he's definitely messing with a band anchor bolt.
nothing learned by all the silence
Hi, i have a 2004 ford e350 with a transmission issue.5.4L engine an. 4R75w trans I think. Sometimes when i put reverse the engine shutdown,unless I press the brake and the gas at the same time to maintain the engine on, to can going in reverse. If you have some suggestions please let me know. Thanks a lot.
is this applicable on 2002 ford explorer wont engage to reverse?
Fuck, I’ve been doing it wrong this whole time! Thanks for explaining this! You saved me $1000’s!!
Did you try it? Did it work?
Everybody whining in the comments section, I found this very helpful.
What might be the reason why the drive gear in not engaging, if you could help me out. Thanks
This was the exact problem I had...if I hadn't seen this vid I would have never worked it out...shogun 2006 3.2...just enough room under there to fix this issue
If your transmission doesn’t let you reverse might as well fork out the money to buy a whole new transmission
Thanks you brother 👍
wherez da proof of dat transmission not working before and working afta dat fix.
English pls 😂😂
that was 3 minutes of my life ill never get back
Looks like the Mitsubishi pajero/triton/challenger/ Delica gearbox
Invecs2.
I think he means : if your transmission reverse gear not working ? this can be the cause and you can fix it this way .
wowow ur so smart... wow......... fail..
Esto me paso en una Montero quite el tornillo pensando que era un tapon de llenado (un error muy comun) pero no lo es, eso es el que tornillo que aprieta la banda de freno si esa se suelta la reversa no entra lo que hizo aqui el chico fue de alinearla con el agujero y volver a poner el tornillo 🔩 si no habria que destapar la caja y ponerlo en su sitio
I recently acquired a 2005 Ford Focus start up put it in gear won't move none of the gears are engaging I hear these transmission are notorious for going out is it bad or is it something....IDK😕
This was in the group of other vids that are ALSO not about what I was trying to learn. That's NOT a 700r4.
Not sure what I just saw
2000 Escalade Denali ??? Will dis work???
The rings man
after attaching back the automatic gearbox to lexus v8 engine the engine starts correctly but the gearbox cannot select gears how can i put the gears back so i can drive
Hi All,
I have lexus LS 430 2002 not engaging into reverse at all,while in forward its smooth.went to workshop they told there is codes of valve body.any one can help what to do?
doesnt address the reason how the gear popped out of the detent.
what kind of vehicle ? It is a rear wheel drive ... no need for talk see what he is /has done but what caused the inner part to slip to start with... is it made to do so under certain conditions ?
good vid.
i am having the same issue i can't switch to reverse gear.
everything is good n smooth.
could it be the reverse switch too?
did you solve the problem?
Kito I’m having that problem now did u fix your car?? LMK please
Ford Endeavor Automatic transmission 2010 Modal Sir, if the back gear of my car is stuck, then tell me any solution.
@@randysavage1841 i had the clutch ban n plates replace. Seem like fluid issue that causes it.
@@Flywithlado-n3k replace clutch n use good fluid.
@@zeus-io3hn Sir, when I checked her with a mechanic, her non swift cable is broken and she is showing the mark on the four wheel drive [4 × 4 L]. Tell me a solution for this. Even after turning off the four wheel drive, that is not happening.
Great video I have a 1976 corvette with no reverse gear in my th350 transmission but forward works just fine how do I fix this ?
Same problem but for a 2011 Ram Dakota hahaha fuuck
When you unscrewed the first bolt, you could hear the inside misaligne, then all you did, was fix the mistake you created. Thumbs Down.
Great video
I drive 2007 honda accord v6 the reverse engage with force what do i do.
Thankyou
Ford Endeavor model 2010 Automatic transmission Sir, if the back gear of my car is stuck, then tell me any solution.
What the heck he doing without explaining what type of transmission it is 🤔🤔🤔🤔🤔
Sir pajero sport manual gear neutral switch is not proper working car pickup drop problem ho raha hai switch se ho sakta hai kya problem.
Thanks
For what kind of airplane is that transmission
Nice video,
great video Thanks
I know thank God for the comments I would never know what the heck this guys doing still don’t know if this will work for my car either
Could hear a darn word he said🥲
I don't have a clue what type transmission this is or really even what you were doing. But I have a 1999 Chevy 1500 pickup truck v6. And I seen a similar video once truck had no reverse and this was the fix. Don't know what this is the same fix for the same situation. But it's definitely not the same video I saw about a year ago don't have a clue what he is doing or on what type transmission
at the end of the video it says 1999 4L60E which is GM rear wheel drive trucks vans and cars duh,.,,.. u cant read or what?
@@fast68chevy this is information that should be given at the beginning not at the end. Not even in the bed itself. You are saying at the end of the video it was stated who is going to set watch your entire video to see if it applies to their vehicle nonsense
What kind of transmission is it?
My Chrysler 300 06 doesn't go reverse, it thinks it's in neutral what do I do
It probably needs a transmission 9 times out of 10 no magic can fix these sort of things. Take it to a shop and have it diagnosed properly
will this work for 2005 jeep liberty no reverse?
My navara menvel gair reversed gair problem
Yeap! Spend a full weekend dropping and putting back a transmission without giving it a full repair, genius! (*sarcasm)
Probably speaks 0 English here illegally
@@jeremiahfisher6994 I'm a Puerto Rican, and Puerto Rico is a USA territory so I'm born USA citizen. The thing is we speak spanish. What I'm trying to say is that USA it's not just people that speak english, maybe he is illegal, maybe he is more American than you, who knows. But I know one thing for sure, in car mechanics, he is a dumb with passport or without it.
I have no idea what you just did.
My Mazda 5 have reverse problem can't move at all .... driving gear works really well...Any idea how to fix the problem...
Take your car for inspection they can diagnose the problem, if the car is high milage that could be a transmission problem.
What kind of car you working with???????????
What transmission is this?
Niceeeee
thanks my good man.
Just about a USELESS example of no info, no description, no fix, and a waste of space
great film, whats it about ?
Will this work for my 95 e320
Hi sir mene apase training liya hai sir HM Chennai plant.
Only Gay mechanic wearing rings in the fingers !.
.
Julio Gonzales let him be gay bro wtf
That explains it! Thanks
Js6 jag no reverse all other gears work help
Will this work on a 1999 jimmy?
My 2011 jeep feel weak in reverse. My driveway has a slight hill. When i back up it it feel like something is bent a little. Anyone have any thoughts.tia.
There is a distance between "back up" and "feel is bent a little". What does "bent" feel like ??
WOW THAT WAS AWSOME YOU THINK I COULD DO THAT ON MY 1986 BUICK REGAL IT CHANGES GEARS WITH NO PROBLEM JUST DONT GO IN REVERSE
If reverse not engage .Do NOT waste your time watching this ???
Is that went it doesn’t engage correct sorry for the dump question just wanna be sure
I have a 2008 impala ss and it won’t go in reverse but it will go forward what should I do
James Harrison burn out turn around
Replace sun shell
or replace reverse solenoid., or reverse clutch discs frictions pack burnt up. or shell broken. and a few other possibilities.
Thanks 🙏
Hi my corsa mark B doesn't wanna go on reverse gear but all the gears are fine
Helo boss nisan super selon 1.6 automatic reves gear can't engech .can u help me plce.
Very Good!... #159 ✝ {6-26-2022}
Automatic transmission ??
Is this a crown victoria
What is it that you did? What is this process called?
kim
bro. kedan manning hi
where you from
Is this applicable on b8 1.8t 2012
Oh Oh I think I know what that is Its a Turbo Inhibitor
Nice video, it pulled up while searching for a solution on my question for a 2014 BMW 135i 6 speed manual transmission that will not into reverse gear, any chance this will work on this problem?
Eddie Kane nope! You will not find a silver bullet fix like that on CZcams. This was not even a fix just a temporary repair until it jumps of the dowl again. It jumped out of place for a reason and it was not addressed take it to a mechanic
WHAT MODEL AND YEAR IS THE TRANSMISION FROM
2004 Toyota avalon
@@maritzavargas4294 no! this is for 1999 4L60E GM rear wheel drive.. see ending of vid it tells you what it is.. wow... fail.
Bahhh!! This is not for range rover
MY POLO 1.4 AUTO JUST LOST REVERSE WAT COULD B DA PROBLM
Great....now i have 5 reverses and 1 forward. Dont do it.
wats da highest speed you have gone in reverse. lol
What vehicle?
what kind the transmision is that, for what car
dorian898 it's obviously a mystery since he didn't have brains enough to talk or explain ANYTHING. total fail
English is not the only language in this world...thanks for the video.
This car INNOVA?
He did nothing it's still the same dur
Car name
OKaay
Model
Mudo El hombre
WTF was that?
Is it submarine
it says 1999 4L60E which is a GM rear wheel drive. trucks and rear wheel drive cars and vans too., at the end of the video . ppl cant read or what?
Hey bro gear position
poor video no sound and no explanation what was being done
Clearly foreign so it's not like you'd understand him anyways and you could just use your eyes it's a pretty easy fix
Why did you even bother posting this you don't say anything you don't say what transmission is it is you don't say what the problem is you don't say what the solution is