Video není dostupné.
Omlouváme se.
HOW TO MAKE NANO LEAF |3D PRINTED NANO LEAF REPLICA.
Vložit
- čas přidán 7. 08. 2024
- In this video, I will show how to make Nano Leaf Replica with the best light diffusion ( BETTER DIFFUSION THAN ORIGINAL NANO LEAF).
STL file and connections diagram- www.thingiverse.com/thing:515...
Files and more - www.mediafire.com/folder/8ncu...
EasyEDA file for modifying -www.mediafire.com/file/48gdes...
Controller used- NODE MCU v3
Led strip - ws2812b addresable led strip(5v)
00:00 INTRO
00:32 PCB AND LED SETUP
04:06 DIFFUSER ACRYLIC VS 3D PRINTED
07:20 LED CONFIGURATION 2
07:35 CONTROLLER
08:16 FLASING WLED
09:46 WLED SETTING
11:27 PANNEL INSTALLATION AND LED EFFECTS
Comment below for any query
00:54 33leds are in parallel connection not series connection
Great looking project I indent to make myself. Could you please supply the gerber for the controller PCB, Cheers. Keep up the good work.
Your every project is very good keep it up
Great work... May i know the thickness of the 3d printed diffuser?
You did a great job brother.
keep this type of work going on
❤❤
Wooow I'm love with this video
u are the best 🖤
awesome work brother
Nice
good...👍
Hello, cool project and i would like to make this but am i correct and is in the gerber file the controller pcb missing?
I believe the second configuration may work if you had a diffuser behind. Like an aluminum sheet. The first configuration is cooler and allows a lot of effects but is too much work
❤️❤️❤️
Great video, one question, why the green wire is not used?
Hi Bro,
Inspired from your work I have requested the creator of Corsair iCue Emulator Node MCU to include support for LC100. So that the nano leaf sort off gets connected to the iCue. Can you please check it and make a video. I am getting my 3D printer this week and will be trying that myself as well. Thanks
You did a great job my friend. Could you please share the pcb gerber file?
you could use magnets between the lights 😀
How does it work? Where can you buy such joints?
Great job but so many questions. Did you provide an idea for the power supply? When you buy the Node MCU v3 does it come with the tan plastic thing that you soldered it to?
Using 5v 5amp power supply.
U can configure it in Wled by putting the output amp of your power supply.
I have used the generic esp8266 module.
Tan plastic is a female berg strip. not needed if u soldered directly. I have used it so that I can easily remove the esp module when needed.
@@electronautic5510 thanks for your response, many utubers don't even respond to questions.
Great video! Can you please make a link for the PCB design?? I also use EasyEDA and am interested to make this project.
Sure
www.mediafire.com/file/48gdesry3re14w5/PCB_PCB_nano+leaf_3_2023-04-03.json/file
@@electronautic5510 Thank you so much!! Definitely earned a new sub!! ;)
howw i order the same pcb as you use here????
What is total cost?
In every panel you have put 60 leds total in count.. But in program.. You mentioned 27 in every segment.. Hows that...? Also if I dont use pcb and directly put led strip just as ur prev project where you created small size, how should be connection. Can you please give digram of circuit? How can i stick 60 led strip in circular as you did but without pcb... Using wired connection as your project previously. Could you please give circuit connections diagram for it?
Some led are in parallel connections that's why 27 led count.
Without PCB, not possible, too much wire will make a mesh inside and it will block the light and create a shadow.
How do you connect every single piece ?
All are connected with connector.
Inside each pannel there was a connector check the video from 02:49
@@electronautic5510 ohh ok and please tell me how you created the base which have imprints of solder and how much overall it cost to you
Check on CZcams how to make pcb.each pannel cost approx rs600
hello can you please share the pcb file so we can order the custom pcb on pcbway?
Link in the description.
@@electronautic5510 yeah i saw it and downloaded all files bjt it seems like there are some missing files to complete a custom order... do you have those files by any chance? I think it should be an gerber file... or do you have maybe a link where you can order it directly?
Ok i will upload the main file again.u need to modify it because i have designed for custom build
Which file extensions u want? Where u want to edit the pcb?
@@electronautic5510 so if possible i would like to have it as it is or betzter sayd so that it is compatible with the stl files you added same size same outcome just in gerber file as id like to order some pcbs on pcbway as i have no idea what im doing without your helpfu video and as its the most intresting project of what i saw and i really wanna try to do it. can maybe also do you know the dimension roughly?
sry for bothering and big thank you i will definetly subscribe to you as youre alredy helpful thank you
Dm me electronauticyt@gmail.com
Want to share something with u,
how to make it properly.
What is the max number of pannels?
10,20,30 whatever you want just need to put the value 'number of led' in wled.
Max no of led for WLED progrms is 960 I guess, im not sure
16
The green wire is not used, correct?
I also have several other questions pertaining to the power supply. Could I email you?
Yes
S4S
3D printer ... ok 😂 👍
Nice