Wonderfull video!! I have just repair a A06B-6058-H334 with your indications!! Thank you very much. I had to install a external relay and wiring from the board.
I run accross a Fanuc drive amplifier problem few weeks back. We use a repair service now since our boss wipped out our inhouse repair facility. I had 4 units tagged "Repaired and Tested" all fail to work properly one by one. 3 of them failed to even boot up. Ive spent all shift swapping bad drive for bad drive. Kinda depressing if you ask me. I think the next shift got lucky with the final, fifth drive on the shelf.
McDonald did a great job repairing this amp but for too cheep of a cost in my opinion. Outside repair service charges a lot because they replace the contactor, bridge rectifier, and output transistor every time even if they test good. A cleaned up contactor will work for about 1/2 the life time of a new contactor. So the question really becomes repair cost vs down time changing out an amplifier. No disrespect intended. Repairing an amplifier in house means no huge pile of replacement parts on hand and you want to keep the cost down.
Your a bad ass. I wish I had a service guy like you near me .I'm about to pay 3k for what you just did. I feel better knowing there is a guy state side who can do it.
Dear Mr.McDonald, I would like to ask you how to repair the problem of Funac amplifier (A06B-6089-H104). It is presumed that these days, the weather is getting cold, which is caused by the deterioration of the characteristics of the components inside the amplifier. When the main power is turned on initially, the error code "414" servo alarm is displayed on the computer monitor and "8" is displayed on the amplifier. At this time, if heat is applied to the hot air near the amplifier, change the "8" => "5" => "2" to the amplifier for normal operation. Please let me know how to fix this problem. I appreciated it for your kind attention on this matter. Thank you so much. David Choi.
Hello Mr. Choi. I hope you and your family are doing well. I used to live at Kunsan and Suwon when I was in the USAF. I will always have a fond place in my heart for the Korean People. Hear is a link to the PDF manual for your drive. fanuc.pennineuk.com/library/pdf/a06b6089.pdf Check out the section on "LED indications and meanings"
I have repaired this fault by removing and replacing the electrolytic capacitors on the power board. And while I have the drive disassembled I clean the contacts of the contactor as you viewed in this video. Removing and replacing the electrolytic capacitors is tedious work. I don't replace the large DC Bus Capacitors. Unless I see signs of leakage on their bottoms. Electrolytic capacitors are easily the weakest link in any electronic device.
Dear Mr. McDonald, I wold like to ask you how to fix the fanuc amplifier problem. (A06B-6164-H311 # 580 - amplifier all in one). Weather getting cold. This is due to the loss of the internal components of the amplifier. Everything is fine when the main power is turned on. However, when the z1 axis moves, the "SV0410 Z1 excess eror (stop) and SV0411 Z1 excess error (moving)" error code of the servo alarm is displayed. There are two cards in the amplifier. The top board was tested is working. Problem is power bottom board.Please let me know how to fix this problem.I am lokking forward to your answer.
Hello. I have a A06B-6059-H206#H511 Given me the 401 Servo Alarm (VRDY OFF)... unit is on a Kitamura Mycenter 1, I watch both videos in reference to the VRDY OFF... will see if the issue is related to that...
I am always happy to see other folks that are troubleshooting and repairing their electronic devices. Thank you very much. I hope my video has helped you.
Hi. I have error code 3 ( low dc voltage) i have troubleshoot everything it says in the manual. Even replaced the amplifier with a new one but the error code still exist. Any idea whats causing the alarm?
Hi there....I have problems with my lathe control fanuc 21-t I would like to know if you can give me some advice because in my small country there is no fanuc technician specialist.... thank you very much!!!!!! data: sometimes when you leave the lathe on with this error when you turn it off and on the error disappears but then when you turn it on in automatic mode it works for a few minutes and stops showing the error again.... --------------------------------------------------------------------------------- Alarm code: 1 in servo aplifier fanuc A06B-6079 ------------------------------------------------------------------------------------------------- In the panel control lathe : 414 servo alarm : x axis detec err 414 servo alarm : axis detec err Any advice on what it could be?
Thanks. You seem to have alot of videos, so i thought you must be busy. I really enjoy watching your videos. I appreciate the effort you put in to putting them up. I always learn something watching them. Thanks. Hope you are doing well. 😀
hello, i have a20b-1000-069, when i turn up for a short time the alarm 12, can you tell me the case about this error, wish you and your family always happy. thank you
Hello, thank you for stopping by and watching my video. I have tried finding a new relay, but with no luck. If you know of a good source for this part please let us know. That sure would make life just a bit easier. HaHa. Thanks again.
@@PeepawMcDonald i've replace relays on boards, just not fanuc boards. i didn't think about finding the correct relay would be that hard, maybe it is. still, nice video. ps. usually are local electronics store can find what we need.
Wonderfull video!! I have just repair a A06B-6058-H334 with your indications!! Thank you very much. I had to install a external relay and wiring from the board.
instablaster...
Paranbéns, I am Brazilian and work in the area of electronics with cnc. Great content.
thyank you so much man
you are a great person
you saved me so many times
i love you
may god keep you alive for centuries
I run accross a Fanuc drive amplifier problem few weeks back. We use a repair service now since our boss wipped out our inhouse repair facility. I had 4 units tagged "Repaired and Tested" all fail to work properly one by one. 3 of them failed to even boot up. Ive spent all shift swapping bad drive for bad drive. Kinda depressing if you ask me. I think the next shift got lucky with the final, fifth drive on the shelf.
McDonald did a great job repairing this amp but for too cheep of a cost in my opinion. Outside repair service charges a lot because they replace the contactor, bridge rectifier, and output transistor every time even if they test good. A cleaned up contactor will work for about 1/2 the life time of a new contactor. So the question really becomes repair cost vs down time changing out an amplifier. No disrespect intended. Repairing an amplifier in house means no huge pile of replacement parts on hand and you want to keep the cost down.
Your a bad ass. I wish I had a service guy like you near me .I'm about to pay 3k for what you just did. I feel better knowing there is a guy state side who can do it.
I know I'm late to the party but great video. I appreciate the content. Cheers
You are a big help and keep posting video. Thank you very much
i'm from Indonesia. thanks you very much master
Thanks for repair vid much appreciated.
Great video. Thanks for sharing.
Great video good job thanks for sharing information .
Good job man thanks for your lesson.be Happy
I like your background music, very calm down my brain, what is the name of it?
Good on you!!!! Good job!!!
excellent video
i love this guru
I am pakistani.. nice video peepaw.
Good job
can u tell me abut alarm 07 in fanuc Alfa drive a06b 6087 h115
need help
Tedioso? para mi es emocionante
Dear Mr.McDonald, I would like to ask you how to repair the problem of Funac amplifier (A06B-6089-H104). It is presumed that these days, the weather is getting cold, which is caused by the deterioration of the characteristics of the components inside the amplifier. When the main power is turned on initially, the error code "414" servo alarm is displayed on the computer monitor and "8" is displayed on the amplifier. At this time, if heat is applied to the hot air near the amplifier, change the "8" => "5" => "2" to the amplifier for normal operation. Please let me know how to fix this problem. I appreciated it for your kind attention on this matter. Thank you so much. David Choi.
Hello Mr. Choi. I hope you and your family are doing well. I used to live at Kunsan and Suwon when I was in the USAF. I will always have a fond place in my heart for the Korean People. Hear is a link to the PDF manual for your drive. fanuc.pennineuk.com/library/pdf/a06b6089.pdf
Check out the section on "LED indications and meanings"
I have repaired this fault by removing and replacing the electrolytic capacitors on the power board. And while I have the drive disassembled I clean the contacts of the contactor as you viewed in this video. Removing and replacing the electrolytic capacitors is tedious work. I don't replace the large DC Bus Capacitors. Unless I see signs of leakage on their bottoms. Electrolytic capacitors are easily the weakest link in any electronic device.
My daughter is within the week going to have a baby. If you could, please keep her in your thinking. Thank you so very much.
Hi tech . Brovo young man.
Have a nice day
Alpha SVUC drive!!
matur suwon pak
DEAR PEEPAW PLEASE MAKE A VIDIO FOR ALARM 8.,AND 9. FOR ALPHA SERVO DRIVE
Dear Mr. McDonald, I wold like to ask you how to fix the fanuc amplifier problem. (A06B-6164-H311 # 580 - amplifier all in one). Weather getting cold. This is due to the loss of the internal components of the amplifier. Everything is fine when the main power is turned on. However, when the z1 axis moves, the "SV0410 Z1 excess eror (stop) and SV0411 Z1 excess error (moving)" error code of the servo alarm is displayed. There are two cards in the amplifier. The top board was tested is working. Problem is power bottom board.Please let me know how to fix this problem.I am lokking forward to your answer.
Hello. I have a A06B-6059-H206#H511 Given me the 401 Servo Alarm (VRDY OFF)... unit is on a Kitamura Mycenter 1, I watch both videos in reference to the VRDY OFF... will see if the issue is related to that...
Hello Sir, thank you for stopping by... please let us know how you repaired your servo drive. I hope you are having a good day with your family.
I am always happy to see other folks that are troubleshooting and repairing their electronic devices. Thank you very much. I hope my video has helped you.
Please make video on fanuc current/Isolation transformer (a76l-0300-0133)
Where are you from sir.
Hi. I have error code 3 ( low dc voltage) i have troubleshoot everything it says in the manual. Even replaced the amplifier with a new one but the error code still exist. Any idea whats causing the alarm?
hii mr.peepaw Mcdonald i just have one question pls reply
how can i learn fanuc drive repairing?
if you know some institute or some plase pls suggest.
What's the cause of a DRDY ON alarm at power up?
Hi there....I have problems with my lathe control fanuc 21-t
I would like to know if you can give me some advice because in my small country there is no fanuc technician specialist....
thank you very much!!!!!!
data: sometimes when you leave the lathe on with this error when you turn it off and on the error disappears but then when you turn it on in automatic mode it works for a few minutes and stops showing the error again....
---------------------------------------------------------------------------------
Alarm code: 1 in servo aplifier fanuc A06B-6079
-------------------------------------------------------------------------------------------------
In the panel control lathe : 414 servo alarm : x axis detec err
414 servo alarm : axis detec err
Any advice on what it could be?
Great!
Love watching you at work. Just wondering if you work for yourself? or are an employee? Cheers Matt
My boss travels the world. And sends me things to repair that he cannot fix in the field.
And industrial factories also send in their items for me to repair.
Between the two, I never run out of things to repair. HaHa.
Thank you very much for stopping by and watching my videos. I hope that you are having a good day.
Thanks. You seem to have alot of videos, so i thought you must be busy. I really enjoy watching your videos. I appreciate the effort you put in to putting them up. I always learn something watching them. Thanks. Hope you are doing well. 😀
It's mccoff relay? thank you
hello, i have a20b-1000-069, when i turn up for a short time the alarm 12, can you tell me the case about this error, wish you and your family always happy. thank you
Sv0012 sv drivr off circuit failure
(x) (y) (z)
Can you help me
What about SRDY off akram??
Hi my dear friend
Pls kindly share this schematic for me
Mazaktroll servo driver alarm
Hi sir. please help me . i have question ? servo amplifier ( type A06B - 6066- H006 ) alarm number n0.8 . help me ........ thank sir
why not just replace the relay?
Hello, thank you for stopping by and watching my video. I have tried finding a new relay, but with no luck. If you know of a good source for this part please let us know. That sure would make life just a bit easier. HaHa. Thanks again.
@@PeepawMcDonald i've replace relays on boards, just not fanuc boards. i didn't think about finding the correct relay would be that hard, maybe it is. still, nice video. ps. usually are local electronics store can find what we need.
fanuccontrolrepair.com/ has the relays.