Belt Weigher Tare and Span Calibration || Schenck Process

Belt Weigher Tare and Span Calibration || Schenck Process
@Technical Manas1
Mail Id- [e-mail]
Instagram ID (for call & DM) - manas_shit_123

[@shakilahmedraza905]

You are a very good professor

[@prateekdevsingh]

Thank you dada bahut achha samjhaya apane
Aur aise hi vedio banate rahiye..

[@TechnicalManas1]

Jarur banayenge

[@viswanatha825]

Good information ihave clear dout bahuth acha thanku very much

[@som2671]

Thank You So much Appke Waja se Mai Calibration jan paya thank you Sir
❤❤

[@TechnicalManas1]

You welcome

[@AshishSingh-rn8jn]

Weight feeder me parameters alag rhega ya same rahega ,jo load latkayenge wo kisme put krenge weight feeder controller me, p3.08 smaer rhega kya

[@OMGCircle247]

Bahut bahut Dhanyawad ese video khi utube channel par nhi hai ,Kuch fault releted video v dal dijiyega boss

[@TechnicalManas1]

Ahista ahista dalenge .... Bas Bane rahe .

[@guptasachin236]

Shandar explain kiya bhai

[@TechnicalManas1]

Thank u

[@prabirakumarmahanta3323]

Very nice bro ty.... LIW OR WF KA V VIDEO BANAO

[@shantanumajhi5408]

Very Helpful

[@prasadbommaji7764]

Thank you,

[@bairiganjansahoo5589]

Thank you so much for the lovely video.

[@bairiganjansahoo5589]

Belt weigher and weigh feeder ka callibration same hai na?

[@TechnicalManas1]

Han same hi hai .
Plz share the video

[@jasvindarsingh6165]

Thankyou ❤❤

[@puspanjalijena6659]

Hello sir if applied and displayed weight are let 100kg
Now I will put lever ratio as 2
Then will display load will be 200kg?

[@TechnicalManas1]

Yes your load will be 200 kg .
Because......
F= Q * L * H * Cos(a°)
F is acted load on load cell (Kg)
Q is weight per unit length (kg/m)
L is effective platform length (meter)
H is lever ratio
a° is belt conveyor angle.
From this formula, u can see if your lever ratio is 2 , then your displayed load will be 2 times.

[@puspanjalijena6659]

@@TechnicalManas1 okay sir
Let Q=100kg
L=2
H=1
a=9°
That means we have to apply 200kgs on the weigh scale platform
Then load on load cell will be= 100*2*0.987=197.53
But Displayed load will be 197.53/2=98.765
Now if I calibrate that value..
Controller will calibrate that 200kg as 98.765 right sir??

[@TechnicalManas1]

No ..... If u hang 200kg , your Q will be 200kg divided by effective platform length (L). If your L is 2m.
Then your Q will be (200/2) = 100 kg/m.
Then F= 100 * 2* 0.98 = 196 kg

[@puspanjalijena6659]

@@TechnicalManas1 Okay I Got that.. But then Controller will show 196kg/meter?
(Like if L Is 1meter and I applied 100kg. Controller will show 100kg/m.
Now if L is 2 meter and I applied 200kg. Then controller will show 100kg/m also)
So I got confused here
Controller will show 196 kg or 98kg?

[@TechnicalManas1]

Yes. I hope u understand.
Gd Morning 🌅🌄

[@rajivrai4235]

Aur sir Drawing kay phara ga ta hai us par knowledge di gi ay

[@TechnicalManas1]

Okk

[@rajivrai4235]

Good evening sir.aur us din error aa raha tha aur Belt conveyor band tha tab bhi dikha raha tha material count ho Raha hai.sir trouble shooting par video nhi bani ay please sir

[@TechnicalManas1]

Totalazer count ho raha tha matlab.... Speed sensor bypass tha controller parameters Mai.
Kaun sa company ka hai belt Weigher ?

[@TechnicalManas1]

Mera Instagram ID - manas_shit_123 main msg koro, aur photo khichke send karo

[@shaikmeharaj5011]

Suppers

[@Rakeshkumaryadav-ld4ld]

Sir mere feeder me error lc input alarm aa raha hai

[@TechnicalManas1]

Reset kariye, agar reset nehi ho raha hai toh cable aur load cell ko check kariye.
Load cell JB mai supply voltage bhi check kariye

[@user-rj7hs6lm1e]

Thank you Sir 🙏

[@TechnicalManas1]

Most welcome

[@user-rj7hs6lm1e]

@@TechnicalManas1 IPA BCW -DS controller Sir please make a video and upload it on youtube sir.

[@rahulchoubey1735]

General faults ko kesay check kartey ispar tecometer error k

[@TechnicalManas1]

Ek separate video banaunga

[@pravinkonade1753]

Kab banayege general fault video...

[@manasswain7060]

Span correction factor 0.6100 se uper Nehi jata hai kya karein

[@bairiganjansahoo5589]

Weighing system ke uper video aur banaiye, jaise pura doubt clear ho jaye, callibration main kuch bhi problem nehi hoga😊

[@TechnicalManas1]

Ok. Kuch video baki hai....
Jaise aap kaise belt angle measurement karenge aur Load cell ka milivolt feedback measure karke weight calculation karenge .

[@bairiganjansahoo5589]

@@TechnicalManas1 LIW & BLMS(bin level measurement system) uper v video banaiye

[@bairiganjansahoo5589]

@@TechnicalManas1 ek doubt hai, callibration gravimetric mode main ho sakta hai? If yes how? If no why? Plz reply 🙏

[@TechnicalManas1]

Garavemetric mode calibration nehi hoga. Kyunki garavemetric mode Mai speed vary hota hai . Calibration k liye speed constant chahiye. Volumetric mode apka open loop mode, garavemetric closed loop. Jo load cell ka weight k upor speed kom ya jayada hota hai.

[@bairiganjansahoo5589]

@@TechnicalManas1 callibration ke tym belt empty rahega, aur hum full set point main belt chalayenge, to callibration possible hai ki nehi?

[@AshishSingh-rn8jn]

Tear Span krne ke time belt runing rhega ya nhi

[@TechnicalManas1]

@@AshishSingh-rn8jn Han belt running rahega

[@srijansingh9834]

Sir belt circuit time kaise nikale please explain with example

[@TechnicalManas1]

Part-01 and Part-02 video dekhiye

[@mizanurrahaman2407]

Kindly send the schenck process number for enquiry and quotation related

[@TechnicalManas1]

You can approach through their website.

[@mizanurrahaman2407]

@@TechnicalManas1 I called him and they are transferring call from one to another

[@TechnicalManas1]

Ok I will give you

[@TechnicalManas1]

mail id - [e-mail]
Mob - 8030403600

[@RabindranathKhanra]

Pls, mention how to calculate/ measure "pulse per length (I/M)"...... Parameter code P02.04.

[@TechnicalManas1]

Full calculation in Part-02. Please watch the video.

[@shaikmeharaj5011]

Hi

[@TechnicalManas1]

Hlw