How to Build a Beetle Narrowed Adjustable Beam 1966-79 by Limebug
Vložit
- čas přidán 5. 07. 2024
- Product:
limebug.com/product/t1-1966-7...
Limebug Gen-II 1966-79 Fully Assembled Beam, how to guide
Install Information:
- Model: 1966-79 Volkswagen Beetle (Ball Joint)
- 4" Narrowed Adjustable Beam
- Compatible with all Ghia / Beetle and Trekker models 1966 and later (Beam Model)
- No Body Mods required, 100% bolt on
- 4-Piston Titan Wilwood Brake Kit in Porsche PCD 5x130
- 100% Bolt on
00:00 - Intro to VW Beetle / Ghia Ball Joint Narrowed Beam
00:21 - Preparing the Torsion Leaves
01:33 - Preparing the Beam for Torsion Leaves
03:16 - Torsion Leaves Installation
04:58 - Beam Shock Tower, Skid End Installation
06:44 - Trailing Arm Grease Seal Installation
07:02 - Main Beam Complete
07:22 - Preparing the Beam for Trailing Arms
07:30 - Trailing Arm Installation
08:21 - Grub Nut and Pinch Bolt Installation
10:01 - Camber / Castor Nut Installation
10:30 - Dropped Spindles Installation
12:12 - Shock Absorbers / Dampers Installation
13:24 - Beam Adjuster Base Setting
14:13 - Beam to Spindles Complete
14:22 - Preparing / Assembly of Track / Tie Rods
15:44 - Track / Tie Rod Installation
16:25 - Steering Damper Mount Installation
17:22 - Steering Damper Installation
17:53 - Fully Assembled Beam to Complete upto Stub Axle
18:16 - Body Mount Nut Install
18:33 - Beam Bolt Spreader Plate Positioning
18:45 - Disk Brake Kit Introduction
18:53 - Caliper Mounting Bracket Installation
19:28 - Disk Brake Preparation
19:48 - Wheel Bearing Preparation
19:59 - Press in Bearing Races
20:54 - Grease the Front Inner Wheel Bearings
22:32 - Grease Seal Installation
23:39 - Grease the Front Outer Wheel Bearings
25:11 - Spindle Nut and Thrust Washer Preparation
25:23 - Disk Brake Installation
25:38 - Spindle Nut and Thrust Washer Installation
27:09 - Clean the Disks
27:28 - Wilwood 4-Piston Caliper Installation
28:18 - Brake Pad Installation
31:06 - Brake Line Install Information
31:28 - Fully Assembled Beam to Complete upto Disk Brakes - Auta a dopravní prostředky
Thanks
I've always wondered how to set the camber adjusters when factory originals had a mark and had a default factory setting when new camber adjusters doesn't have that mark
The largest flat side is the maxmum castor side on the reproduction camber nuts. I hear what you are saying but as you rotate it is largest flat open side of the nut, the initial indent is good as an indicator for first installation but is of no real use once the beam is assembled as during tracking an angle gauge/ alignment jig would be the primary measuring tool.
Hab von bugz kein Plan aber schaut gut aus ✌️
Danke, das ist sehr nett
Muy buen video. En que pais estas ? Saludos
Merci, voici comment construire une poutre VW Beetle 1966-79 entièrement assemblée
You didnt even pack the wheel bearing bruv.
We didn't fit the grease caps for this reason, same with beam is ready for grease pack but still "dry". Thanks for pointing it out though, good to know you watched the vid!