XTOOL RA2 PRO In-Depth Setup Guide, Assembly, Examples, and RA2 Tilt Upgrade!
Vložit
- čas přidán 27. 06. 2024
- In this video I will take you in depth into getting started with the XTOOL RA2 PRO rotary attachment combined with the XTOOL D1 PRO! I will take you right from the unboxing all the way to the complete workflow of processing various rotary engraving jobs.
XTOOL sent me the D1 Pro 10W combined with the RA2 rotary tool to test and I've been genuinely impressed with the build quality of this laser cutter and the rotary tool. This is not a long term review, however, and the opinions expressed in this video are (at this point in time) more like first impressions. That being said, the apparent quality of the RA2 leads me to believe it will perform reliably over time. If anything changes, I will come back and update this video description to report my findings.
In addition to the setup guide, I have designed and made available two new modifications. First is the PCB and button cover as seen at the beginning of the video:
► embracemaking.com/products/xt...
The second is the RA2 riser and tilt mechanism. This tilt mechanism kit allows you to continuously adjust the position up to 40 degrees both ways. Other tilt kits on the market often just lift the metal base in one direction only by lifting the end of the base. This kit mounts the main assembly on top of the T-slot profile and allows you adjust the center of mass above the base so that there is no risk of the assembly tipping over:
► embracemaking.com/products/xt...
I have also designed and made available a fume extractor nozzle to eliminate fumes at the source:
10W D1 Pro version:
► embracemaking.com/products/xt...
20W D1 Pro version:
► embracemaking.com/products/xt...
You can find the accessory snap latch case here:
► embracemaking.com/products/ru...
Always remember to practice proper laser safety. These lasers can seriously harm you directly (your eyes) or indirectly (your lungs and health). ALWAYS wear your safety glasses! By-products from processing certain materials can be toxic and harm you. DO NOT CUT vinyl materials like PVC. Check this list for hazardous materials before cutting something:
► wiki.atxhs.org/wiki/Laser_Cutt...
If you are looking for products or items I've used with the D1 Pro in this video, see below. As an Amazon Associate may I earn from qualifying purchases (at no extra cost to you):
XTOOL D1 Pro 10W:
► www.xtool.com/products/portab...
XTOOL D1 Pro 20W:
► www.xtool.com/products/portab...
Alcohol Prep Pads (Clean Skin Oils Off Surface Before Engraving!)
► amzn.to/3hOSQ3s
Electric Screwdriver Kit
► amzn.to/3WhkTYk
Digital Measuring Calipers:
► amzn.to/3WddZnd
12 Inch Speed (Rafter) Square
► amzn.to/3PKvIjl
8 Pack Black Water Bottles
► amzn.to/3G8uQlr
12 Pack Black Wine Tumblers
► amzn.to/3FKrbZx
6 Pack Black Mugs With Handle
► amzn.to/3hJVGH8
3 Speed 90,000 RPM Electric Compressed Air Blower
► amzn.to/3jnfzEb
Laser Proof Silicone Work Surface Mat (20" x 28")
► amzn.to/3zDyMG7
Laser Proof Silicone Work Surface Mat (23.5" x 31.5")
► amzn.to/3A0Fzv1
If you want to go more in depth with the XTOOL Creative Space Software, check here:
support.xtool.com/hc/en-us/ar...
SAFETY WARNING: DO NOT CUT THESE MATERIALS:
► wiki.atxhs.org/wiki/Laser_Cutt...
Thank you @xToollaser
0:00 Intro
1:17 Unboxing
2:46 PCB and Button Cover
3:52 RA2 Basic Setup
7:40 Cylindrical Objects on Parallel Rollers
11:30 Adjusting the Parallel Rollers
13:04 Roller Steady Rest
14:28 Installing the Rotary Chuck and Jaws
18:50 RA2 Tilt Mechanism Upgrade Installation
23:04 Setting Up Mug With Handle
24:52 Installing Extra Leg Extensions
26:11 Removing Laser Guard For Extra Clearance
27:40 Engraving Mug With Handle
31:31 Setting Up Objects With Tapers
33:56 Engraving Tapered Wine Tumbler
36:48 Setting Up Spherical Objects
38:50 Setting Up Rings (External)
39:20 Setting Up Rings (Internal)
40:45 Outro
#laser #ra2 #engraving
****************************************************************************
If you enjoy and have benefited from my content and are feeling generous I would love your support! You can "buy me a coffee" here:
► www.paypal.com/donate/?hosted...
By supporting my channel you are encouraging me to continue with this time consuming endeavor.
Follow me on Instagram!
► / embracemaking - Věda a technologie
Since making this video I have also come out with the 'RA2 Rotary Switch' to making changing between rotary and regular Y-axis functions quick and easy. No need to plug and unplug your connectors anymore leading to potentially broken wires and connectors. See the video here: czcams.com/video/HZ4KskP16Ak/video.html
The quality and thoroughness of this video is inspiring. God, I love engineers.
Thank you so much... how did you know I was an engineer :)
Just received my RA2 tilt upgrade, and assembled it. Total game changer. Awesome idea and product.
Glad you like it, thank you so much for the feedback!
You’ve been an amazing asset to starting my new woodworking/craft business with my new Xtool D1 pro!! Keep up the fantastic work!!!
Thanks
Jason Mielke
Thank you so much for the compliment and the donation. Very much appreciated Jason and best of luck with your business endeavors!
Recently started using D1 pro, and by far, this video is the total package. Easy to follow and professionally made. I'll be following this fella more. Thanks!
I purchased this attachment from your website and it’s definitely as described. I’ll make a quick video of me using it. I already set it up and it only took me 5 mins. Your video is straightforward and makes life so much easier. Thank you!
Thank you so much for your support and I'm glad you like it!
One of the best-explained videos I have ever seen on CZcams excellent!
Wow thank you for the great compliment!
Nicely done! Thanks for taking such a large amount of your time to make the machine worth it for them to send it to you. Very good info.
Thanks for acknowledging that! These videos take a lot of time to produce :)
Great In Depth Video, saved this one for any trouble shooting. Well Done!
Thank you Christopher, much appreciated!
Another very helpful video. I ended up ordering your tilt mechanism for my rotary tool. Thank you for what you do.
Awesome, thank you for your support :)
Your videos for the xTool are absolutely awesome! Thanks to your videos, I was able to get set up and working within a few hours (I took my time with assembly) including with the RA2 Pro. I went ahead and ordered some stuff from your website and I am a bit upset at how long the shipping is taking. I did not think from Canada to the USA would take nearly 20 days. For those of you in the United States that are thinking about buying some of his products, beware at how long the shipping might take. My order was shipped a week ago and it is still in Canada with an expected delivery date of May 18th. Keep the videos coming!
Hi Adam, thank you for the kind words. It looks like your order was placed May 2nd, shipped next day May 3rd and scheduled for delivery May 17. About 15 non-business days which isn't lightning fast (I understand) but based on tracking it looks like it sat in the distribution center here in Canada for 4 days without movement. Normally this doesn't happen and with international tracked air mail (my standard shipping to the US) most packages take 7-8 days. I'm not really sure why yours is going so slow :( Sorry about that
Unfortunately US Customs is the WORST when it comes to shipping from Canada to the US. I've shipped many items to the US and 75-90% of the time, US Customs holds it up for the most ridiculous reasons! It's worse with low value items, I think they believe all low value items are containing something illegal, it's just crazy! Then when the person receives the package, either it hasn't even been touched or it's been repackaged, I assume the original package looks like it was shot at or blown up! They've gotta do better 🤦🏼.
Wow, this video was amazing. Very detailed and helpful. Please keep it up.
Thank you so much!
great job with the video. ive been wanting to use the RA2 for a while. im going to give it a go this weekend. keep up the good work!
Thanks, will do! Lots more XTOOL content to come, hope you can subscribe :)
Great video. I have the F1 but watching this really helped me better understand the RA2
I've got some rotary goodies coming out for the F1 soon :)
Thank you for your very detailed reviews. Well done!
My pleasure! Thanks for watching!
Best video for the Ra2 I have seen!!
Thank you Steve!
Very thorough and great use of gotchas to teach features.
awesome video fella, keep em coming
Thank you Adam!
I've watched a crap ton of these videos and always learn something. I knew about the first tilt method, but I didn't think to use the chuck, if it has an open end.👍
Glad you found something new in there :) Thanks for watching!
Great and informative. Love your mods also
Much appreciated! Thank you
I bought the nozzle from them and it works so well I took my box off.
Thank you! Glad you like it!
Thank you! Thank you so much for always being on point with all of your videos!!!
Thank you so much, really glad you're enjoying them!
@@EmbraceMaking BTW, my order for the RA2 Pro Tilt Mechanism Kit is taking forever.
What is your order number? I can look into it for you - wondering if there has been some kind of shipping delay. Thanks!
@@EmbraceMaking EM6688
Wow! Great detailed video and I like what you made to tilt at an angle but I have the enclosed smoke box and I can't raise it any higher. I still wanna thank you for a great video
You're very welcome! Is it the XTOOL enclosure that you have?
Nicely done
Thank you! Cheers!
Very helpful!
Glad it was helpful! Thanks for leaving a comment!
Your base design is fantastic. If I can make a suggestion, I would like to see an better leveling system. I would like to see it on a single screw so that I don't need to tighten both sides. And also with a wing type nut/screw so that I can make adjustments by hand. These are the only things keeping me from purchasing. Nice job overall.
Nice work with your tilting part 👍 I'm tempted to order one for engraving the inside of rings easier. I just have a few questions:
Do you have a video showing the inside of a ring being engraved? (I'm sure I heard the angle had to be 45° if this is the case 40° will not be enough)
Once the tilt is connected and at its highest angle (for the inside of rings) will it not be too high to fit under the F1? (which I would be using to engrave)
How much would this cost in GBP (including shipping?)
If the questions are answered positively could you give me the link to buy please?
Amazing video that really helped me out! I just bought the RA2 Pro Tilt and fume extractor for my D1 PRO but I couldn't find those xtool risers you showed on the video. Do you still sell those? Thank you for your videos and the awesome and helpful 3D printed tools to make my life way easier!
Risers are included with the Tilt Mechanism kit :) Thanks!
Hi great information here. Helped me alot... I was wondering if the laser goes, do you have to purchase the whole laser module part or can you just buy the laser by itself and install it. Because it seems a bit expensive like 500 bucks just to get a working laser!!! Any help appreciated 👍👍👍
First, let me say thank you for your awesome video. Now I would like to say, I have found that you don't have to flip your image if you go into the rotary setup and click mirror output.
Good tip!
your design is very useful.. similar design to ATEZR Chuck Rotary
Your videos are amazing! Would the RA2 Pro with the tilt upgrade work for a large tumbler with a handle (thinking the 30oz/40oz Stanley tumblers with handles)?
Thank you! If you have a really large tumbler you can always slide the tilt mechanism to the end of the base so the handle won't hit it. If that is still not enough room with the extra height the tilt already adds, you can lift the base with a book or something underneath.
Great video! How often would you clean the lens if you were just engraving tumblers?
Thank you! I guess that sort of depends, if you had air assist or vacuum drawing the soot away it might help lessen the frequency of cleaning... Maybe try doing a dozen of them and see if you notice any deterioration of quality between the first and the last... if not keep going. Keep the first tumbler for reference. If you start to see loss of detail or weird artifacts then inspect the lens.
Awesome video - well done.
I have just send you a message about wanting to purchase the tilt mechanism, shipping to Australia.
Thank you Alan, will get back to you!
Thank you for your very informative videos. I put together my D1 Pro with your video alone and now to about the RA2 Pro. I have a question, when engraving an ID bracelet, how would I engrave the back of the bracelet? The engrave surface is curved.
Depends on how curved... if it is very severe that would be tricky. If it is a gentle curve you might be able to lay it flat on the table and set the laser focus distance on a middle ground between the closes point and farthest point on the bracelet. As long as the laser head doesn't contact the parts of the bracelet that are sticking up off the table. This is something you may have to experiment with a little to get the best focal distance.
I purchased the switch. the tilt mechanism and the D1 Pro light kit a couple days ago. Can't wait to get them. Thanks for the great video and products. I didn't see the motherboard cover on your website. I would have got one of those too. It there a 3D printer friendly SVG file so we can print that our selves?
Hi Christy, the mainboard cover and button cover come as a package: embracemaking.com/products/xtool-d1-pro-pcb-and-button-cover-kit Currently the STL files are not available but perhaps in the future I can look into offering those in some way. Thanks!
Just started unboxing my 20w unit. Your videos are excellent both in thoughtful content and clarity.
Do you know of a switch someone makes to swap between the cup and the frame instead of unplugging the cables each time? I can see that as an eventual point of failure at the Pc board.
Ha. Cancel. Just read your edited message
Glad you found it! For anyone reading this message in the future, the RA2 switch can be found here: embracemaking.com/products/xtool-ra2-y-axis-switch
Thank you!
Loved the video. I just tried my rotary/Chuck first time and I am getting the same line like you did. Cleaned the lens and that still didn't help? Was your problem something else?
Hmm lens cleaning seemed to fix the issue for me... is this still happening for you?
When installing pully for chuck attachment, whats the reason to turn the flad side of motor rotor as pully hole is round, like there is no similad D shape ?
Are you the guy that gives ATV reviews? The similarities are insane!!!
Nope but send me a link! Would love to see my doppelganger lol!
Great video...easy to follow. How can I purchase that awesome tilt-mechanism?
Hi Michael, thank you! You can get it from my website here: embracemaking.com/products/xtool-ra2-pro-tilt-mechanism-kit
When etching a handled mug how do you put the logo on the side of mug not on opposite side of handle? Thank you
Well this is exactly what I need. Will this work with the S1? I have the riser base installed on my unit as well.
If you have the riser base it should work for you... should give you enough clearance!
I noticed you had pre-set settings for BLACK SS Tumblers. I'm looking for the settings for WHITE and I'm told I need to slow it down for white. When I look in my Creative Space under Materials, there is nothing there like in you folder. Where Are they supplied from Xtool? Great informative video also.
Thanks Larry, are you running the latest version of their software? I would agree that for white you will likely have to slow it down so the laser can be better absorbed by the white paint.
What type of connector is for the stepper motor? Does it come with alternative connectors? 3 pin, 4 pin?
Hi, nice video, i have a question, can this tool be used with other engraving lasers ? I have a raycus stative laser and would like to know if i can use this accesorry. Thanks!
If your laser can control a four pin rotary motor then the RA2 can probably be controlled ... You would just need to adjust your software to account for the right number of steps per rotation so your images aren't distorted
Have you listed your STL files for printing our own PCB covers for sale anywhere? I would love to purchase the STL and print one for my own use.
CONVOLUTED
Great video! Would a 5W Xtool with RA 2 be a setup for a beginner? Not sure whether to go with 5 or 10W. Any advice would be appreciated! Thank you.
Go with the 10w, unless you plan on strictly engraving I wouldnt go for anything less than 10W
@@EmbraceMaking thank you!!
@@mrob5278 Nobody ever wished they had less. Buy the biggest you can afford. The 40watt is a marginally larger size 'dot' so it is arguably lower resolution for engraving so the 10watt would be better for that... but even so, the 40 watt can be ran at 10watts.
Very thorough, thank you. My ra2 pro motor sputters and not working right. I did the chuck reset and still doesn’t work. Talked to xtool customer service and still waiting for resolution. I’m wanting to fix it myself to work with my new xtool f1. Any suggestions would be much appreciated
Have you checked the pins on your cable? Sometimes with repeated plugging and unplugging you could have a bad connection
Do you have any info on a stepped down 30oz mug please
I m new to laser machine and in market to use for making cards from cardstock paper and some miniature wood piece. I have Cricut maker machine.
1) does it work on cardstock paper or too strong for it?
2) other tool air assist or honeycomb is optional in such application? like to try first and gradually like to add accessory.
3) what is longevity of this machine?
Hi there! Any chance you could tell me what the height of this RA2 is from the bottom side of the base to the center of the 3-jaw chuck? I think this could to be great axis for one of my other machines but am looking for this dimension to confirm fitment. Thank you!
Hey sorry for the slow reply. With my tilt mechanism its 105mm from bottom of plate to center axis. Without my tilt mechanism its about 71.5mm Hope that helps!
Question... I like the xtool, but am leaning more towards one of the other brands. The biggest thing holding me back is I think this rotary attachment is the best out there.
So question... Are these rotary attachments proprietary to the brands, or could I use this rotary with another unit (running lightburn)?
Love your angle mod as well!
Thanks! You should be able to run it with other brands.... it even comes with adapter cables to fit other lasers. What other brands are you considering?
@@EmbraceMaking it will actually be a little while still, as I'm in the process of building a new garage/workshop and want to wait until after that... With how fast things are changing with diodes, will probably change by then. I'm torn, I think I want to get a k40 co2 machine for the faster speed and ability to engrave acrylic etc. But I mostly want to be able to customize larger woodworking projects, which the k40 would be very limited on. So thinking maybe a 20w ish diode as well. For straight diode, was looking at the Atezr 24w. Love the ability to set it on any surface with essentially limitless size workpieces. But I'm also likely going to be getting a CNC router as well, and pretty set on the Onefinity Elite 48x48, and could get a 24w diode attachment for that, which would be a huge default size for a laser, but you can't move that onto a large work piece, so all tradeoffs...
I also have a S1 10w can i use the RA2 with it ? or do I need to now get the riser box for the S1? thankks
Yes the riser base would be necessary for use with the RA2 !
1) this is great
2) I would have just not engraved a mug with that handle lol
hi. AT 15:05 when you take out he rollers, it appears you are using the worlds smallest battery powered screw remover. Where did you get?
Right here: amzn.to/3WhkTYk
Hope you don't mind it's an affiliate link (no extra cost to you and 30% off right now it looks like! )
Thanks!
Where can I get one of those PCB covers!? Great idea!
Thank you! You can find them here: embracemaking.com/products/xtool-d1-pro-pcb-and-button-cover-kit
Hi, I would really love to buy your rotary attachment but looks like you don’t ship to Australia. Is there a supplier in Australia that you use? 😊
Hi Merilyn, please visit my contact page here: embracemaking.com/pages/contact and send me your address and I will get you a custom quote. Thanks!
is the tilt kit plastic or aluminum? Also i dont need the extensions as i only have the F1, discount on the price :)
It is a plastic part. I just recently received the F1 so I hope to have a video of the tilt mechanism working with the F1 soon :)
With the additional extenders will I still be able to use the D1 Pro enclosure?
You should be able to, I personally don't have the xtool enclosure but there are quite a few others who have purchased the rotary kit and are using the enclosure without issue.
I have 3d printed leg extensions for my LM2 and get some vibration with laser movement. Do these legs cause the same problem? My legs are 25mm square with locking pieces in the center to lock into the block above.
I haven't had this issue with my printed leg extensions. Do you notice the vibration when using the extensions for regular XY engraving, or with the rotary engraving? Or both
@@EmbraceMaking just xy
does the d1 pro. engrave on stainless steel?
Hi I'm new to all this. Very good stuff here. Wondering if you can help. When I'm ready to engrave, the last goes out and rotary stops moving. Tried 10 times now. I've done all the settings, frame so on. Lights are on but when I press start nothing happens. Would appreciate advice. Thanks
So the laser doesn't fire at all? Which software are you using? XCS or lightburn?
@@EmbraceMaking sorry I found out a lead wasn't plugged in. All working now just can't sell anything. Pretty pissed off at mo. Alot of money to part with. I would ask for advice on a new selling engraving business. Hope there's options. Currently trying to sell on eBay. Then Etsy hopefully next week.! I really thought it would kick off
On my d1 pro, I don't have the stainless steel mug or other materials you have. I have some very basic ones. Is there something I need to do to get those?
Do you have the latest version of the software? What version are you running?
@@EmbraceMaking v.1.124. software updated yesterday. I found a way to find some of them. When I click +more at the end of my material list I see it brings up a search tool where you can look for other supported materials and found the blk stainless and even the plain stainless. Appreciate your videos and the products you made and sell. I ordered a few. Love the Galaxy watch charger; brilliant!
What type of exhaust fan are you hooking the CPAP hose to ??
This is on the other end: czcams.com/video/k7qTE4t4sf8/video.html
Can't find the main board cover on your site to buy. Please tell me where to order
Hi Gloria, it's here, it's included with the button cover: embracemaking.com/products/xtool-d1-pro-pcb-and-button-cover-kit
Thanks!
got my upgraded today but very sad to see it does not work with the S1 its just far to tall even with the riser to work...bummer but thank you for the videos
Hi Shawn, the S1 requires the riser base from XTOOL to accommodate the RA2 even without my tilt kit. Do you have the riser base?
Surprised you didn’t build a jig for lining up the ra2 base.
Hi I used my RA2 but the image. does not look round. how can O fix that
Is the RA2 Pro compatible with a Sculpfun laser machine?
Possibly but truthfully I have no experience with that machine. The RA2 comes with a bunch of adapter cables so you would have to investigate to see if the adapters will work with the Scultpfun. In rotary mode essentially the Y axis gets replaced with this rotary motor so you would configure your software accordingly to rotate the correct amount on the y axis for the diameter of the round object you are lasering.
what is the usual cause for a tumbler to slide back and for when framing
When you say back and forth, do you mean along the axis of rotation?
@@EmbraceMaking it moves left and right and falls off the level attachment so spins like a drill and falls forward if that makes sense
Do you have any xTool P2 videos?
Sadly not yet! Maybe XTOOL will send me one someday :)
Can you demo how to engrave a glass?
At some point soon I will give the glass a try!
Well done!! Just as soon as I have money falling out of my ass I'm getting one!!
I think they are running a sale right now... might want to check!
Where I can track my order , I purchased the rotary attachment 11 days ago en still waiting for it
Hi Juan, did you get the email from my website with tracking number? I also replied to your email. Check your spam folder if you're not getting them. I'll reply to you again by email - tracking is showing it's still on the way. I'm in Canada so it looks like your order spent about four days in customs which I unfortunately can't control, sorry about that.
@@EmbraceMaking I got the email thank you for the info , I can track the package now
Is it compatible with Sculpfun S30 pro max?
Hm, not sure but hopefully someone else can step in and confirm...
@embrace making could you answer my questions from 3 weeks ago please?
Nice work!
Just a well intentioned message from a potential future customer ...
I looked at your website and apart from a few dead links within the website: isn't there an obligation for a legal notica in your country? I couldn't find out where you're from - and specifically where your goods are from. I don't like to order things that are then on the way for weeks. You probably had a shipping information button, but that didn't do anything either. I am interested at the RA2 Pro Tilt Mechanism Kit, but the shopping experience is not really satisfying ^^ With a "whois"-request I've seen, that you are using a service from Toronto, Canada for your website ... so I guess the goods will ship from there? ^^
Thanks for your message! Yes I'm located in Toronto so that is where the items would ship from. In terms of legal notice I'm not sure in regards to what you would be looking for a notice? Maybe you can explain further. Can you let me know which links are dead, some of the Amazon ones? Unfortunately those I have to continually chase around when Amazon runs out of stock or a seller makes a new listing. My site is still under construction as it is somewhat new. I am working on getting better shipping rates to offer options such as expedited service international etc so that will be a better experience for people soon. I'm also working on getting some help with filling my orders so I can spend more time improving the website and making more designs and videos :)
@@EmbraceMaking The „legal notice“ is a thing here in europe. That is where i am looking for the city/country as a last try if i couldnt find it anywhere else on the website, because there have to be all information about the company. This was just a question :)
On the page for the tilt mechanism:
The link to the snap latch box is a 404. The panel with shipping & return do nothing if you try to expand it.
You should at least put the information on your website, from where you are shipping. Without going through the whole checkout process. Your site switch to euro as soon as i enter it, that gave me false expectations :D I guess the shipping cost from canada to western europe would be as expensive as the whole tilt mechanism ^^
You can do whatever you want, these are just my 2 cents with a good intention behind it :)
Thanks for the info! I just fixed the link to the snap latch case. Not sure how that one got broken :( I will find some time today to try and add some information about where the items are being shipped from. Perhaps more info in the contact page form. The reason the website switches to Euro when you visit is that the website is created with Shopify ecommerce platform. So by default it detects your location and shows you your local currency. I appreciate you letting me know :)
Do you sell the file for the attachment so I can print it? 18:53
How to purchase xtool RA2 pro machine from nepal.@ price
Where are you located
The switch to the square nuts is not a good one - they bind very easily, to the point where I simply cannot use your tilt mechanism. I couldn't even be bothered to fight with installing it.
Hi Steven, are you referring to the all metal nuts in the channel? You're the first to have had this issue to my knowledge. If this is the case please contact me using the contact form on my website and I can get you some of the original hex nuts with the plastic inserts if you like those better! Thanks!
I got the RA1. Completely worthless. The rollers move so fast that the cup slips resulting in a horrible carve/burn.
The RA1 with only the rollers isn't the best. The RA2 with the chuck is way better - anytime I can use the chuck it is my "go to" over any roller setup because of slipping. You can try and weigh the cup down with sand inside - lots of workarounds out there but it requires more setup time and can be a hassle
Loved the video and ordered almost everything you recommended. However, cannot find where you have shipped anything and am wondering where my stuff is. Confirmation #(removed for privacy).
Thank you Steve! Editing this response as I previously typed the wrong information. I just responded to you via email with tracking info. You should have received a message from my website with tracking info but sometimes these go to spam folders. Thanks!
@@EmbraceMaking Thanks a million!