How To Replace 1992-1994 C4 Corvette Water Pump
Vložit
- čas přidán 12. 09. 2024
- This video will show you how to replace the water pump on a 1992-1994 C4 Corvette, Buy new water pump: amzn.to/3hRJwtc
#corvette #c4corvette #waterpump
Disclaimer
Our videos are for entertainment purposes only. It is recommended that you seek advice or help from a qualified professional while attempting any and all repairs.
Do-it-yourself repairs can involve risk and injury, we assume no responsibility or liability for losses, damages or injuries that include but are not limited to direct, indirect, special, incidental, actual, consequential or punitive. All repairs performed by our viewers are at your own risk.
While we do review products that we use daily or have even used for years, we also review and test products for companies that have compensated us to try their product out. We are independently owned, the opinions expressed are our own from personal experience while using any and all products.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites. Recommended products with links may be commission-based when products are purchased from them.
Buy new water pump: amzn.to/3hRJwtc
I’ve watched several videos of this.
I like yours the best.
About to tackle my ‘96 LT4 water pump
Thanks
Thanks for watching
Exactly what my ball bearing looked like!
Does the tensioner have to come off to access the bottom driver side bolts on water pump?
I think it was in the way, we may have removed it to gain access to those bolts.
great video...gonna do mine in the morning...ty
Thanks for watching! Don't forget to subscribe!
Nice!
Thanks for checking us out.
I found one oring on the new water pump shaft.
The service manual says, the ringed mark on the tiny double female shaft goes against the engine block.
do you know exactly which hoses you used as i am going to order them separately as im picky and like certain brands
I believe we bought them on Ebay. I am not sure which vendor was selling them. They came in a kit.
You decided not to put an O-Ring on the coupler that goes between the Water Pump and the Cam Gear? I was hoping that you were going to show which side of the couple goes to which side of the Cam/Water pump. You did notice the O-Ring groove on the coupler?
If there was an o-ring in there we put it back on.
Ring marked side goes against the engine, per my service manual
The way to install belt is place it around AC compressor wheel last.
Thanks for the added tip! Hope you enjoyed our auto repair video that shows you how to replace the water pump on a C4 Corvette
Is it not necessary to use thread seal on the long bolts so that antifreeze doesnt leak through the water jackets and through the threads?
We didn't have any leaks using the method that is shown in the video.
The bottom bolt on the left side of the engine dose go into the water jacket and can leak without sealant.
All four long bolts tops and bottoms ones of my 95 had white sealant close to an inch long on the bolts tip area from factory I think. YES USE SEALANT
What kind of gaskets did you use exactly, I have two choices one factory AC DELCO in pump box new and I have FELPRO gaskets as well. TWO emails and FELPRO swears to install their gaskets dry only. What exactly did you cover your gaskets with. THANKS FOR ANY HELP I am confused I see ChrisFix smoothered his in fine a thin coat of RTV. What shoulod I do! My AC delco box instructions say fiber gaskets most be used with a sealant.
Im about to put my 95 back together and I had a quick question. My Haynes manual says I need 2 o rings on spindle shaft when mounting water pump but I noticed you skipped this step. Is it OK to proceed with no oring? I'm sure you've done enough of these to roll your eyes at.
It you follow the video you should be okay. When you take the old one out see if there is more than one oring.
I'm in the middle of a water pump job on my 96 and I also referenced a Haynes repair manual. Like you said, it indicates there are 2 Orings, one on the spline driven gear end and one on the back of the pump spline. Mine were missing completely, maybe they can deteriorate over time. Great work on the video! Thanks
Is it necessary to remove the serpentine belt for water pump removal?
I think we had to.
@@HomeOwnerRepair definitely have to, as you do it creates space to get to one of the bolts. Found out today!
Thanks for the reply anyway!!
Where did you buy the coolant hose set?
I think I found them on Ebay
Is the intake coming off necessary?
No, we were also doing an intake gasket at the same time.
i cant get out the one bolt near the belt… its a pain in the ass without power tools, its my first project car and the water pump went bad the day i bought it. a 95 corvette.
They are not easy to work on. Hope this video helps out.
Sealer on the bolts?
We didn't need it.