Haha, we've all been there! You got the job done. For this kind of size, using hotair to remove is a good choice. Another technique is the good old razor blade - cut the leads near the top of the ic, remove the plastic bit, and then use chisel tip with some flux to pick up the pins that are soldered on. This brings risk of breaking up pads though, if you are crazy with it. I think when soldering back on though, I would wick the existing tin off the pads, and then pin the four corners manually with a soldering iron, some flux, and a bit of solder on the tip of the iron. Then, after you pin the chip in place you can manually solder every pin using the drag technique or just doing it one pin at a time with a needle tip. Usually flux is a good thing, I think though you went a bit overboard with it. It just made you have to clean alot more. Experiment with your usage of flux, you may be surprised how little you need to get the job done.
@@andrewortman4402 amazing brother i take not i will try to do one by one hopefully you will see the video when i make one exactly how you explained i do not have better flux but i hopebi will buy soo as i am still learning Thank you immensely for sharing the knowledge
Get hot air to 340* and scalpel, heat up places where solder is "glue dot" - individually no need to try to preheat whole chip around whole time, put scalpel between pins where "glue dot" are from top to bottom and back out, you will get rid of the Solder glues from between the pins.
I somehow suffer from watching this
@@sherman5k756 how so?
Watch this
czcams.com/video/P3F3CEKiypU/video.htmlsi=3fPgJ_kyendNd_98
Haha, we've all been there! You got the job done.
For this kind of size, using hotair to remove is a good choice. Another technique is the good old razor blade - cut the leads near the top of the ic, remove the plastic bit, and then use chisel tip with some flux to pick up the pins that are soldered on. This brings risk of breaking up pads though, if you are crazy with it. I think when soldering back on though, I would wick the existing tin off the pads, and then pin the four corners manually with a soldering iron, some flux, and a bit of solder on the tip of the iron. Then, after you pin the chip in place you can manually solder every pin using the drag technique or just doing it one pin at a time with a needle tip.
Usually flux is a good thing, I think though you went a bit overboard with it. It just made you have to clean alot more. Experiment with your usage of flux, you may be surprised how little you need to get the job done.
@@andrewortman4402 amazing brother i take not i will try to do one by one hopefully you will see the video when i make one exactly how you explained i do not have better flux but i hopebi will buy soo as i am still learning
Thank you immensely for sharing the knowledge
Get hot air to 340* and scalpel, heat up places where solder is "glue dot" - individually no need to try to preheat whole chip around whole time, put scalpel between pins where "glue dot" are from top to bottom and back out, you will get rid of the Solder glues from between the pins.
@@ArturSobkow noted thanks you and you are highly appreciated for sharing your knowledge i am greatful!🙏
You remind me of good old days
@@Arkkukie thanks are you now a professional?
I absolutely want to see more of this. 😄
Subbed.
@JamieBthe2nd well stay tuned I have managed to do solder it better will upload soon please do subscribe
@@MurangaZW looking forward to it. 👍😁
@JamieBthe2nd thanks I will sure you the one I think I solder better
@@JamieBthe2nd czcams.com/video/sBngaX1FEbg/video.htmlsi=j17tbktJk5aaKZYK
@@MurangaZW Nice. 👌
well this is too relatable i think
@@AbdulHadi-uw4qy 😂😂😂 well when i see people doing it it looks so easy i guess its because of practice
@@MurangaZW true
@@AbdulHadi-uw4qy i did try again and i think i got it right even though it wasn't easy
@@MurangaZW well congrats cuz i never get a second chance -_-
@@AbdulHadi-uw4qy oh sorry to hear that but why did you get another chance
Nice!
@@Qdacool_animations thanks
Take time and practice you will get it
@@Chikafu.M thanks 🙏
is bro not aware of solder paste
@@thatlittlefrog. no bro is learning though those are dead pcb that i use for practice
like i said do not put to much flux in it...🤣🤣🤣
@@FreAk_dr. thank you brother we did it
My god ...
@@AbDouRed-vf4hl it's funny 😁 isn't it 🤣
More flux and more solder is always the answer for this guy, but not s better technique
@@diegovianavillegas3297 thank i will take note what can i do to improve
Dont you ever solder again. EVER.
@abdoun8214 but why I love it I awill keep trying I have already done some job like changing type c changing port
@@MurangaZW just joking , lol
@@abdoun8214 i can take a joke 😂
@@abdoun8214 checking this out
czcams.com/video/P3F3CEKiypU/video.htmlsi=3fPgJ_kyendNd_98
quit soldring bro.
@reedski it's too late bro ain't no way I will be quitting I have a lot of dead boards and I have a hot air station what should I do with it
czcams.com/video/P3F3CEKiypU/video.htmlsi=3fPgJ_kyendNd_98