Video není dostupné.
Omlouváme se.
Dewalt DCF899 nut gun, running but the anvil is not turning. How to fix.
Vložit
- čas přidán 1. 03. 2023
- Some how a random steel ball bearing has got into the gearbox and jammed up the impact hammer on the shaft. With the iimpact hammer not ingaged the anvil is free to rotate on its own.
These dewalt impact guns are generaly very good and give very little trouble. They are buy no means the most powerful impact on the market, but they are one of the most durable. Motors very rarely give any problems and only seem to stop running after several years of hard abuse.
#dewalt
#dewaltnutgun #dewalttools #dewaltrepair #tools #powertools #toolrepair #repair #deandohertygreaser #repairmachines #diy
As much as the talent you show in repairing these tools, you have to hand it to the designers of the tool itself. A lot of work has gone into developing these tools and how they work. Also, get a load of the size of that spring would you and the meatyness of those parts what a beautiful design. Thank you for allowing us to see the repair and inner workings of these tools it's very fascinating watching you repair them.
amazing video, i work for dewalt service in belgium as a technician. We even do not open it but replace the part in total. That is because we need to repair a lot of tools in a day and sadly we do not have the time to go in full depth. The only thing you are doing wrong is the grease part. It schould be white and black grease on the gears and not yellow. Also de nose schould be greased up. But at the end grease is grease ;) amazing job. We schould do it like that to. It would be much cheaper for the customer to let his tool repaired.
Keep up the good content it’s very entertaining I guess I’m a bit of a nerd. While other people watch Netflix I watch repairing videos.
Like that you give more info on this video, some of us are dummies and don't read between the lines yet until we get a better understanding of it
Good to see the master at work. You cannot buy years of experience. Thank you for the schooling. 👍
Looks very similar to my MAC Tools impact, except mine has brushes, gave me more confidence to take it apart, regrease and check for any damage, amazing video.
The Mac tools impact is a dewalt. You can even swap over internals.
Nice one. Portrait shot👌
Well done with that one 👍🏻 threw me for a loop filming in portrait mode
On mine the anvil stopped turning too. I took it apart and the impact hammer mechanism was just jammed - I just unjammed it by moving it around with my hand and the spring snapped it back. Put it back together and it works now. Hopefully that helps someone.
Great video. Thanks for the explanation and walking us through the process.
This was a very useful video to me. I got a Ryobi one that has a broken steel ball as well. Now I know how to fix it.
Excellent video Thank You for taking the time to make it.
Thank you and God bless you
Superfluous Third Ball
That’s a new one.
I am surprised the 18v was still around in 2018. Thought the 20v was the thing.
It is regional. 20v marking is only for US.
20 volts is a marketing gimmick. when under load, the running voltage from the batteries generally floats around 18 volts, but in thye flexvolt/powerstack batteries, I think ive seen those measured closer to 19-20 under load.
18v is 20v max
That ball bearing actually is in the Anvil I repaired a few of them and they have been there
Thank you so much for this video, I’m learning how To repair these as we speak. I didn’t know how the ball bearings went in on the impact or shaft. What grease are you using for reassembly?
Mate you certainly know your power tools your knowledge is extensive on all types
Could you advise me of all the battery gear out there which one would you buy over another
Cheers
Great stuff
very informative and interesting helpful video, thank you, glad there is no pounding drums or swirling whooshing intrusive background noise, great vid
I just tore mine apart today. I have no idea what the cause of the poroblem is. Everything looks normal.
Great video.
Thanks!
Addictive viewing and what type of grease are you using and are there different types for different tools/ areas on the tools?
How important is it to have the plastic thrust washer in-between the anvil and housing? Mine somehow got torn up and jammed in the gun causing it to have a lot of drag with a depressed trigger. Finding the washer itself is rather difficult. I can only find a kit with the anvil and housing
Awesome video!
When this problem picture ? If someone drop the gun or when ?
Hey bud the one side of the anvil on my Dewalt DCF880 broke off. Can i still use it while waiting for the replacement part?
can you tell me what grease you used when you put it back together...?
Yes plz
Lets say nothing about the washer leftover on the bench! :-D
Mad!
What do you use to clean the grease off the gears they look so clean
Brake cleaner spray, just be careful with it around rubber and plastic parts.
Where do you get those long driver bits?
i got some on ebay
👍👍
Live to UGGA DUGGA another day 😅
When you have 3 balls instead of 2 its always a problem
As long as the shaft is ok
Did a drunk Scot lose his kilt the other night ?
You’re wasting your time repairing that stuff. With your talent you could repair anything.
Did you murder a Scottish man?
У меня тоже была такая проблема на 400H ryobi , также размолотило стопорные подшибники.
Thanks for finding and fixing the problem, I've already ordered the part. Sure its easy to throw it away, but I actually enjoy fixing stuff. Take care, sir🫡.