HOW TO REPLACE ENGINE MOUNTS ON A 2007 DODGE CALIBER
Vložit
- čas přidán 12. 09. 2024
- #mrtalentedreid
am really sorry for the subscribe button flashing in the video. am apologizing for any inconvenience it may cause. when we are new to editing error do happen. please accept my apologies.
DIY-HOW how to change a engine Mount.
year 2007 dodge caliber .
rear engine Mount changing.
side engine Mount changing.
tools type
10mm
16mm
17mm
13mm
sockets
spanners
18mm
17mm
16mm
"Keyword"
"2007 dodge caliber"
"2007 dodge caliber sxt"
"2007 dodge caliber alternator removal"
"dodge caliber"
"dodge"
"caliber"
"2007 dodge caliber ac compressor replacement"
"2007 dodge caliber thermostat replacement"
"2007 dodge caliber transmission fluid change"
Any chance of removing that annoying logo in the middle of the screen, so that we are able to see the full view. I think it would help dramatically.
Am sorry sometime when you new in doing something you make mistakes
My dear you have a good job please don't stop continue keep going keep rolling, the lord of God will be your protector are your Guardian
Amen thank you 😊 nice comments 👍
That subscribe thing is in the way!
Wow sorry about that. Thanks for stopping by
@@MrtalentedReid what is that extension you are using to loosen the screws in the back?
Hold on let me check
I Use a 1/2 inch drive and 1/2 drive sible joint
Your name really goes with your skills. You are very talented for real.Thank you for this video . Will show my cousin this video . I think that will help him with his car ok
Thank you so much I really appreciate your support god bless you
Thanks for the tutorial but that subscribe button is gonna give me an aneurysm
Sorry
Nicely done my friend , nicely done!
Ok great thanks for stopping by
Other than that I think your video is great. Keep it up
Appreciate it
You should never start a bolt with impact your lucky you didnt strip the block
Doing a job take tactics and skills something you know and do everyday
When using a impact wrinch to start a bolt u must be a experience person Doing so and know the feeling of dragging a threading or when it getting tight to stop if it's not catching properly am not a job guesser
And I can see where quite a few domb dislike the video because they can't do it but that's how the world is evil to who doing something constructive than violence.
Did you use an impact drill for the last one?
Yes
How do you remove the other two mount bolts. There is no clearance to get any tool to them between the bolt heads and the motor. It looked like they weren’t even in when you pulled it out.
thanks
You are welcome
Thanks for sharing this tutorial, do you need to support the engine from underneath, or is that only for the rear engine mount?
Thanks for stopping by it's best to support the engine with a jack where it would be easier for you
You could can the music. Would rather hear your narration while you're working.
No one seems to understand my accent so am sorry
Dude - 🙏 thank you! I am replacing my motor mounts on my 07 d.c right now. But where do I place the floor jack?
Under the engine thanks for stopping by hope you have a blessed weekend
Please feel free to become a part of my channel thank u
Where do you place the jack when doing this type of job.
Under the transmission depending on the type of jack you may need to place a peace of bord on it
Okay thank you 🙏🏽 I was trying to figure that out the whole time I was watching you work. Great video btw.
Ok take care have a blessed one
Thanks for sharing , i also have Vibration Problem
The engine have Vibration when started and it stays through all the raunds , and somtims no Vibration through the day , so any ideas ?
Check if any of the motor mount have any damage
And while doing so check it the exhaust pipe touching the body of the car
Driver side transmission mount takes 16mm on those bottom hard to reach bolts?
Some carry 16mm 18mm so it's best to get a socks set reason for that sometimes they swap the bolts so you never know
Any recommendations on getting all 3 of the bolt holes to line up on the metal plate? Took out the motor mount installed the new one but can’t get the three bolts to line up with the long bolt in the mount to the holes through the metal plate.
Thanks for stopping by u can use a screw driver to line up the holes 🕳
It’s a good video but what’s with that subscribe thing in the middle of the video that’s annoying
Oh dang I really sorry about the inconvenience of that subscribe thing that was some error while editing the video as a new editor am really sorry 😞
how many engine mounts are there? 3 or 4? i have issue with them and need to change them all
I think it's four but if you go to the parts store they will provide you with the right amount
@@MrtalentedReid thank you 🙏 I am ordering them online all together as set is about 150€ here and 50€ cost for changing they asked me, I’m not sure if I can do that on my own
Ok
I heard these were similar to the Dodge avenger will the video be close to it or far off?
Pls reply ASAP
Close
Most parts for the dodges works
This is really helpful. Only dunce useless people will Dislike it. Useless is a good way to adjust it because i watch it and observe and thats a way of learning focus. Not because it might seems difficult to you it no mean you can't learn something and save your self from spending excessive amount of money, the 4 person who Dislike the video very perfect never make mistakes from they born i guess Dislike the video bless them very well hahaha 😀
100 percent true 👍
how long did it take u to complete the job ?
About 20 30 minutes thanks for stopping by it could be less but didn't in any rush
Can all this be done without a drill?
No
@@MrtalentedReid lol thanks you understood what I was trying to say
No problem
Could not watch video well due to the subscribe word flashing. Try it again but without the word
Am really sorry about that my bad I made a mistake and I apologize for it thanks for stopping by though
All is good I'll still watch it again cause ur video is easier to follow. I too have to replace the mounts.
Appreciate it
do you put the jack on the oil pan! or the transmission
Under The motor but make sure to put a flat peace of board on it or a rubber mat so you don't damage the crankcase
@@MrtalentedReid ok thanks
Your welcome
i just been done did subscribed! ive maybe subscribed to bout 9 you tubers cuz most people cant wrench like 2nd nature they just yakity smackity like their mouths a faucet been done make me nauseous!
Ok