Well I took my bench grinder apart like you said so and used three in one oil but I just found out you're supposed to pack those bearings with grease so now I have to take it back apart again and pack the bearings with grease I had a feeling before I was doing that but those bearings need to be packed with grease so you did yours wrong those bearings have to have Grease because the oil is just going to fly out of there the grease won't move so you have to redo your bench grinder
Amigo necesito una respuesta yo tengo uno de esos y lo necesito pero esta desconectado mi abuelo lo conecto directo a la caja de fusibles pero quería saber si se puede conectar a la casa con un apagadoe
victor rojas ...no me preguntaste a mi pero hay te va la respuesta estos motores son de inducción ósea no necesita escobillas de carbón funciona con motor de corriente alterna acompañado de un capacitor
haciendo calculos ese motor tiene un factor de potencia de 0.94 . Es un poco raro, los motores tiene un factor de potencia bastante malo, solo los transformadores legan a ese valor
I have the exact same bench grinder but the sticker that you have on there was so bad I had to take it off cuz you barely can read it what brand is that bench grinder if you could tell me the manufacturer name that logo at the top of that sticker your sticker is in Hell a lot better than mine mine was like slashed I mean it was so bad it came off in pieces and you don't by chance have a slower version of you wiring that bench grinder do you I really didn't get to see how you wired it too quick LOL that's ok if you don't on the capacitator I have two yellow wires coming out one of the yellow wire is connected to the green wire that goes to the motor the other yellow wire disconnected together with a red wire that goes to the switch then the black wire from the cord connected to a skinny yellow wire that goes back to the motor then the white wire from the cord is by itself with a wire connector on it it goes to the switch so yellow from the capacitor connected to the red wire with a wire connector is connected to the center terminal of the switch spend the white wire by itself with a wire connector on it goes to the left side terminal of the switch that's the way it was wired it does work that way but is that right if you could help me out with that I would really appreciate that and the bench graders pretty Rusty and I saw you took the sides off and oiled the bearings inside I probably should do that to mine too cuz how Rusty it is but there ain't no saving that sticker it's gone LOL and I have to do the same thing for mine the sandpaper on the shafts that hold the grinder Wheels or rusted so I have to do the same thing send them off clean like you did and thank you for showing me how to do that I really wasn't wanted to take it all apart but what I saw what you did I think I should so if you can help me out with those two things tell me if the water is right and the logo that's at the top of your sticker on your bench grinder so I know what kind this is and I hope you can make heads or tails of what I said LOL oh one more thing too I'm replacing the old switch with a new rocker switch has numbers on it 1 2 3 so I just basically hooked up that switch just like it was on the old switch hopefully the wiring is right it works everything turns and works fine but I just want to know if the wiring is right sorry for the long message just need a little help before I pull my hair out LOL I thought I could just replace the switch and paint it and that was it but watching what you did I have to do the same thing I know I do awesome video by the way didn't even know about taking it all the way apart thank you for that so hopefully you can make heads or tails of what I'm saying and get back to me and help me out that would really really appreciate that thanks again I'm going to subscribe to your video give you a thumbs up and hope you keep making more videos
Nada mas hacen un video por hacer que muestra a unbalero se le pone grasa el capacitor jamas lo desconecto es una sobetana estupidez no subas esos videos
el aceite desaparece rapidamente siempre es mejor abrir el ruleman y colocar grasa de alta velocidad y si esta gastado mejor remplazarlo
si eso mismo me pregunte
Excelente trabajo.
pinche metal mamalon alv
Well I took my bench grinder apart like you said so and used three in one oil but I just found out you're supposed to pack those bearings with grease so now I have to take it back apart again and pack the bearings with grease I had a feeling before I was doing that but those bearings need to be packed with grease so you did yours wrong those bearings have to have Grease because the oil is just going to fly out of there the grease won't move so you have to redo your bench grinder
Hola Saludos..tengo uno igual..lo conecto y solo se amarra..y lo desconecto y gira normal
s era lo mismo?
Qué electrodo usó para soldar?
Amigo muy video tengo el mismo esmeril pero nose cómo van los cables ojo es el mismo igual se rompió y se salieron lo cables
Tengo un motor de esmeril DeWalt de 1/2 hp y no tiene bobinas ni capacitor está sin datos como hago para bobinarl
Con ese tipo d esmeril si vale hay adaptar un molino d mano respiran pofavor gracias
Amigo necesito una respuesta yo tengo uno de esos y lo necesito pero esta desconectado mi abuelo lo conecto directo a la caja de fusibles pero quería saber si se puede conectar a la casa con un apagadoe
De cuanto es el capacitor
Con que liquido lo limpia
Serviría mas si explicaras
pero cambiale el rulemannnn ratonnnn.... jajajaja
te fallo el utilizar una llave y no una de tubo para ajustar la base con el motor, igual +10
yo tengo unomparesido y perdio fuerza ?
Buen video amigo dame un sub saludos
Que hiciste? Le cambiaste el estátor?..
Por que no tiene escobillas como los motores de los taladros ?? .
victor rojas ...no me preguntaste a mi pero hay te va la respuesta estos motores son de inducción ósea no necesita escobillas de carbón funciona con motor de corriente alterna acompañado de un capacitor
haciendo calculos ese motor tiene un factor de potencia de 0.94 . Es un poco raro, los motores tiene un factor de potencia bastante malo, solo los transformadores legan a ese valor
Que me recomiendan que haga??? El mio se escucha como si estuviera amarrado
Se desgastaron demasiado los baleros y por consecuencia, el rotor está pegando en el estator. Solo cambielale los baleros
no manches lo mas dificil lo hisite, pero lo mas facil y urgente "cambiar baleros",,,,, que paso?
quien sos chaplin
'?????
Mi hermano necesito informacion de ese esmeril
Marca
md200k
Hola tengo un motor así pero no se como va conectado el capacitor y como va la corriente
Hola amigo cómo está pudiste solucionar el problema
lagos estaba cruzándose la corriente del motor
Aa está bien amigo pero pudiste
I have the exact same bench grinder but the sticker that you have on there was so bad I had to take it off cuz you barely can read it what brand is that bench grinder if you could tell me the manufacturer name that logo at the top of that sticker your sticker is in Hell a lot better than mine mine was like slashed I mean it was so bad it came off in pieces and you don't by chance have a slower version of you wiring that bench grinder do you I really didn't get to see how you wired it too quick LOL that's ok if you don't on the capacitator I have two yellow wires coming out one of the yellow wire is connected to the green wire that goes to the motor the other yellow wire disconnected together with a red wire that goes to the switch then the black wire from the cord connected to a skinny yellow wire that goes back to the motor then the white wire from the cord is by itself with a wire connector on it it goes to the switch so yellow from the capacitor connected to the red wire with a wire connector is connected to the center terminal of the switch spend the white wire by itself with a wire connector on it goes to the left side terminal of the switch that's the way it was wired it does work that way but is that right if you could help me out with that I would really appreciate that and the bench graders pretty Rusty and I saw you took the sides off and oiled the bearings inside I probably should do that to mine too cuz how Rusty it is but there ain't no saving that sticker it's gone LOL and I have to do the same thing for mine the sandpaper on the shafts that hold the grinder Wheels or rusted so I have to do the same thing send them off clean like you did and thank you for showing me how to do that I really wasn't wanted to take it all apart but what I saw what you did I think I should so if you can help me out with those two things tell me if the water is right and the logo that's at the top of your sticker on your bench grinder so I know what kind this is and I hope you can make heads or tails of what I said LOL oh one more thing too I'm replacing the old switch with a new rocker switch has numbers on it 1 2 3 so I just basically hooked up that switch just like it was on the old switch hopefully the wiring is right it works everything turns and works fine but I just want to know if the wiring is right sorry for the long message just need a little help before I pull my hair out LOL I thought I could just replace the switch and paint it and that was it but watching what you did I have to do the same thing I know I do awesome video by the way didn't even know about taking it all the way apart thank you for that so hopefully you can make heads or tails of what I'm saying and get back to me and help me out that would really really appreciate that thanks again I'm going to subscribe to your video give you a thumbs up and hope you keep making more videos
Nicholas it didn't even dawn on me if you speak English or even understood what I said I hope you do
otro video para SORDO MUDOS
buen trabajo pero tampoco me gusto esa musica horrible
Chafa.
Nada mas hacen un video por hacer que muestra a unbalero se le pone grasa el capacitor jamas lo desconecto es una sobetana estupidez no subas esos videos