Audi Camshaft Position Sensors P0340 P0341 P0342 P0343 P0345 | Audi Hall Senders |
Vložit
- čas přidán 5. 09. 2024
- Today we're looking at Audi Camshaft Position Sensors, also known as Hall Senders. A list of trouble codes are listed below.
► Subscribe: / carsntoys
►► Tools: www.amazon.com...
Digital Multi-Meter: amzn.to/2KOdFZD
Tester Probe Kit: amzn.to/3bK6KON
Ratcheting Screwdriver: amzn.to/3BeZmb9
Torx Bit Set: amzn.to/3PugqhL
Wire Brush: amzn.to/2ZeEDzO
HNBR O-Ring Set: amzn.to/3L2qaOX
Power Probe: amzn.to/3CSJvNe
►►► Audi Maintenance and Repair Playlist:
• Audi S4
This particular vehicle is a 2011 Audi S4. Camshaft Position Sensor, CMP sensor, Hall Sender.
G40 - Right Hand Side Bank 1
G163 - Left Hand Side Bank 2
Audi P0016 (VAG 16400) Crankshaft-Camshaft Position Correclation Bank 1 Bank 2 - Adaptive value greater than 139 degrees crank angle
Audi P0018 (VAG 16402) Crankshaft-Camshaft Position Correlation Bank 1 Bank 2 - Adaptive value less than 75 degrees crank angle
Audi P0340 (VAG 16724) Camshaft Position Sensor A - Bank 1 or Single Sensor
Audi P0341 (VAG 16725) Camshaft Position Sensor A Circuit Range/Performance - Bank 1 or Single Sensor
Audi P0342 (VAG 16726) Camshaft Position Sensor A Circuit Low Input - Bank 1 or Single Sensor
Audi P0343 (VAG 16727) Camshaft Position Sensor A Circuit High Input - Bank 1 or Single Sensor
Audi P0345 (VAG 16729) Camshaft Position Sensor A Circuit - Bank 1 or Single Sensor
Audi P0346 (VAG 16730) Camshaft Position Sensor A Circuit Range/Performance - Bank 1 or Single Sensor
Note:
Any attempt to repair automotive parts and/or systems carries risk of personal injury. Always adhere and follow safe practices when working on vehicles. Such as, safety glasses, jack stands, no loose clothing, etc. No guarantee or warranty is implied. Use the information in this video at your own risk. Carsntoys is a member of the Amazon Influencer Program.
Publication, reproduction or distribution of this film is strictly prohibited.
Carsntoys
/ carsntoys
Awesome video! Great troubleshooting techniques along with a complete explanation throughout the whole repair. Good videos like this are hard to find!
This video really helps a lot
Got a video for the exhaust side sensor locations? Theres 4 on the a6 wuattro 3.0 and cant find a single video showing where theyre at...
great vid very well explained
This video was very helpful! I checked mine and turns out the voltage is negative and at 4.98. is that normal? Where do you suggest I check next?
are you testing connector for 5V reference for power ? To know the sensor needs changing ?
You can also switch the sensors left to right on many vehicle to see if the problem follows the part to the other bank
Mine wouldn’t come out so I used a knife and it broke my knife… i hate audi’s with a passion now
Hi, thank you for your video it was really helpful. I do have a question, do you think the codes P0491/0492 could have as root cause this sensors failure?
P04300 can be that? After going high to 7200rpm the fault came in. Hard start and loose power in driving.
I'm afraid that the timing jumped
Thanks for video.. clear and easy..
Can you please help me where is the camshaft position sensors located in 2009 Audi a4 Quattro 2.0 4 cylinder
Are 4.2 have the same location?
Update no they are different
What if the sensors are working properly amd they are reading something worng in the engine. Changing the sensors would not fix the underlying problem, right?
I got a p0021 code could it be that sensor I replaced the timing chain kit and now it’s shaking when in idle no misfires
U ever figure out p0021
Did u found out a fix to it. I got a similar problem 0016 that's why I like to know.
checking this too, I am getting a code for bank 2 camshaft adjustment issue
Im getting this for bank 1, how did you fix it?
What should voltages be on the plug to a camshaft position sensor? I have measured voltages on bank 2, intake sensor and it seems that the left wire is ground but two right ones are BOTH about 5 volts.
Is this normal? I thought one would be 12v or so.
Most sensors use a 5 volt reference form a module
Do you have to disconnect battery to change these?
No.
I don’t have a code , but would it be good to just change these out?
nope, not needed
@@winfle thanks
Have you thought about any mods yet?
Anyone have codes P0016, P0012 come up on their vechile before? I hope its not my timing chain
Yep I had p0016 and timing was jumped on bank 2 Inlet camshaft sprocket. Was 1 tooth out. Major head ache to repair has to remove cat to access covers to retime and replace the top tensioner and guides as well.
Is this a hard job? I was charged $1890 in labor for this
Wow . I don’t think it’s hard I just looked at the parts on my car look very easy to switch
broo...