It’s dangerous to use grease or oily stuff. In case of a emergency break the tire can slipped and turn on the wheel. Better use Dish Soap full washable and not slippery. And you can do the tire in the oven by 50celsius for 5-7min than you can stretch it easier. 👍🏻
Thanks for the bench vice idea! I still had to use three large flatblade screwdrivers to pry it on, and soapy water to lube it, and a rubber mallet to seat it. Advice for others: use a copper face on your vice jaws to avoid buggering the axle flats.
My method was - held the tire in hottest my faucet can get for 5 minutes and then solidered it on using brute force and a help of screwdriver leverage. No lube or anything. Got it done in 5-10 mins.
Hi I installed a new rubber tyre and it keeps coming off when riding do you think its faulty its not the wrong size as I did measure it before I purchased it and got a new one but same thing happened
stuff that. pair of gloves, drop tyre in boiled water for a bit, then use one one of those very mild spray glues that are actually quite slippy when wet. Then just wipe the excess with a mild solvent. good until you need to replace.
Where is the rest of the scooter? How do you disconnect the wire? How do you put it in a vice without crushing the threads on the hub? So many questions!
So to disconnect the wire, you remove the motor. On the downward-facing side is a plate with 6 screws. Remove those screws then push the wheel into the ground to lift up the plate. Afterwards push the wheel into the ground hard, as that will lift the motor enough for you to grab it and pull it out. Now your wheel will be in the same state as in this channel. Btw. the vice isn't gripping onto any threads, there aren't any threads left, after you remove the motor. It's just the emply rim
Vaše svaly jsou tak silné, Koupil jsem si pevné pneumatiky a zkouším to 2 dny, ale nikdy se mi je nepodařilo úspěšně namontovat, 🥲nemám tak silné svaly ani dobré nástroje, mohu vám je poslat poštou, abyste je pomohli nainstalovat? Rozměr pneu je 8,5x2
obejrzyj to czcams.com/video/lxOFGvHBsTY/video.html Kupiłem łyżki i robiłem jak w filmie i zakładanie trwało minutę, czego niestety nie mogę powiedzieć o zdejmowaniu starej opony. Oczywiście mam y6s a nowa opona poszła na tył
Łyzki na allegro po 15-20 zł za sztukę (kupcie 30 lub 40cm) a reszta jest na filmie. Opony bezdętkowe polecam do hulajnogi z amortyzacja przód tył W y6s jest i naprawdę są się jeździć.
@@MrMandelll no I've installed solid tires on my gotrax I don't give a rats ass what the video shows I'm telling you from experience of installing those tires aren't that easy as they make it seem It's a real Pain in the ass If you think otherwise you've obviously never done it
Ok, now I only need to build more muscles in a year or two before 😂
It’s dangerous to use grease or oily stuff. In case of a emergency break the tire can slipped and turn on the wheel. Better use Dish Soap full washable and not slippery. And you can do the tire in the oven by 50celsius for 5-7min than you can stretch it easier. 👍🏻
Thanks mate
bruh
What about boiling it first for 10 minutes
Or just pay a shop to do it
Thanks for the bench vice idea! I still had to use three large flatblade screwdrivers to pry it on, and soapy water to lube it, and a rubber mallet to seat it. Advice for others: use a copper face on your vice jaws to avoid buggering the axle flats.
Don't use a lubricant like this. The tire can slip when breaking and it will use more battery energy as the tire slips around the wheel.
petroleum based lubes could degrade/breakdown tire material, also temporarily reduce grip on road. best to use soapy water solution.
Made it seem so easy without the tire being in hot water 🤣🤣
Forgot to mention that you need to boil the tyre!
i don't do it
Best lube is tiny amount of dish soap in some water use minimal soap a few drops only. Windex will also work well for this one.
How is it all these poxy youtubers think everyday normal people have these tools by the toaster in the kitchen ?
Whats the spray you are using ? If WD40 I think it could be dangerous... but looks like very easy and fast. Anyway I prefer to heat tire ...
I use Interflon
Lube TF (aerosol)
but anything that gives a slip might do
@@Fachura_ thx mate, I will try !! :)
👍👍👍
My method was - held the tire in hottest my faucet can get for 5 minutes and then solidered it on using brute force and a help of screwdriver leverage. No lube or anything. Got it done in 5-10 mins.
Hi I installed a new rubber tyre and it keeps coming off when riding do you think its faulty its not the wrong size as I did measure it before I purchased it and got a new one but same thing happened
So have gorilla strenth
stuff that. pair of gloves, drop tyre in boiled water for a bit, then use one one of those very mild spray glues that are actually quite slippy when wet. Then just wipe the excess with a mild solvent. good until you need to replace.
technic...
You must of heat the tyre up to do that surely!
Where is the rest of the scooter? How do you disconnect the wire? How do you put it in a vice without crushing the threads on the hub?
So many questions!
So to disconnect the wire, you remove the motor. On the downward-facing side is a plate with 6 screws. Remove those screws then push the wheel into the ground to lift up the plate. Afterwards push the wheel into the ground hard, as that will lift the motor enough for you to grab it and pull it out. Now your wheel will be in the same state as in this channel. Btw. the vice isn't gripping onto any threads, there aren't any threads left, after you remove the motor. It's just the emply rim
where can i buy these tires
Aliexpress
Ebay x
can i sprey wd40 on tire end motor to put tire on esier
this is not recommended as you will need to wash well, preferably something that is water-soluble
Hi bro send your post code my scooter is problem
Vaše svaly jsou tak silné, Koupil jsem si pevné pneumatiky a zkouším to 2 dny, ale nikdy se mi je nepodařilo úspěšně namontovat, 🥲nemám tak silné svaly ani dobré nástroje, mohu vám je poslat poštou, abyste je pomohli nainstalovat?
Rozměr pneu je 8,5x2
Super rrápido
I want to know what type of lube you used
Hulk
Super, ja się męczyłem przy Joyor Y6-S i poległem. Pozdrawiam Serdecznie,👍🛴👍🎄
obejrzyj to czcams.com/video/lxOFGvHBsTY/video.html
Kupiłem łyżki i robiłem jak w filmie i zakładanie trwało minutę, czego niestety nie mogę powiedzieć o zdejmowaniu starej opony. Oczywiście mam y6s a nowa opona poszła na tył
Łyzki na allegro po 15-20 zł za sztukę (kupcie 30 lub 40cm) a reszta jest na filmie. Opony bezdętkowe polecam do hulajnogi z amortyzacja przód tył W y6s jest i naprawdę są się jeździć.
@@danieldomanski8600 Bezdętkowe miałem w joyor y10s łyżki już jakiś czas temu kupiłem. Dzięki za dobre rady 👍
This MF gotta hit gym at least 5 times every minute damn it took 3 of my mates and I to struggle one of those on
eh grazie, anch'io se avessi una morsa ci riuscirei in scioltezza
when tou kick the brake you tire will slide around the metal tire bro this is not good 😂
I have not yet had such a situation very quickly tire sticks to the rim
Mines. Not setting all the way
Mine tire isn't that bendable, I can't get it back on
Then put for a little bit to hot water it my help
I used a screw driver and got it on, thank you. Also I just used all of the strength to force it on like crazy and got it on
The local bikeshop here in town put the wheel in the microwave 2 minutes, 1 minute on each side.
Abimnerdesin
Adam yabancı 😁
Ziaomi
Well only if I had a vice, I boiled the tire and it still wasn't enough.
Soapy boiling water, my knee, two scre drivers.
@@huginn_muninn481 did it without took along time now front wheel needs special screw driver which I'm yet to find and then I can try
numaravar ver
Lol You’ll be banging your head against the wall. Just pay someone trust me it’s not worth the stress
Bullshit It ain't that simple
So you think this is CGI? :P
@@MrMandelll no I've installed solid tires on my gotrax I don't give a rats ass what the video shows I'm telling you from experience of installing those tires aren't that easy as they make it seem It's a real Pain in the ass If you think otherwise you've obviously never done it