How To Service MAXXFORCE Fuel Filter Housing /Keeping Your Vehicle Running
Vložit
- čas přidán 15. 07. 2022
- See How To Change Maxxforce Fuel Filter. Prime Maxxforce Fuel Filter And Properly Clean The Fuel Filter Housing. If Your Fuel Filter Housing Is On BackOrder You Need To See This Video! @dairleautoclassicrestorati6892
#maxxforce#fuelfilter#truckrepair - Auta a dopravní prostředky
Sir I admire your patience. Nice and steady speed doing the work doing it correctly pointing out problems that could exist for someone who's never done this before. I do salute you sir you are good.
To receive a comment like this. It makes it all worthwhile. I thank you very much!
@@dairleautoclassicrestorati6892 hey 2011 maxforce 13 red stop 🛑 on. Shop said high pressure fuel pump because it’s not getting enough power. Did that. Sign still on. Now they said it may be the wiring hornets to the motor. But they are not sure? Any thoughts?
@evanwingate7307 It is very possible. I have to say that can be a difficult call to make.
Nice job on the video. It helps a lot!!!
That's awesome 👍🏽
Thank you so much sir!!!!
Thank you Sir
Amazing video. Subscribed 🎉
Thank you!
Thank you very much
I wish you wasn't so far away !!! I'll pay you to come here !!
This video is so helpful! Did you say you cleaned the filter housing by soaking it in varsol? I've never cleaned a part this way and just want to make sure I heard you right so I don't ruin my housing.
Your channel is awesome!
Thank you Sir!
It is not always necessary to remove the complete housing. In my case it was helpful to do so Especially when the dealer is saying you need a new housing. And they are on backorder. Sometimes the Strainer area need more attention than the Fuel.
Awesome video! Mine has a slight rough idle, I changed the fuel filter and when I went to prime I noticed that the prime plunger was leaking. Would that be allowing air to be drawn in and causing idle problems?
Yes Sir!
Good morning Sir I take my filter housing to clean it and now I have small check and I don't know it go ?
I have an international 4300, same set as in the video. I was driving, and the engine just died, and I tried to restart the engine. It would start but cut right back off. I CHANGED the fuel filter and cleaned the strainer. Do you have any suggestions on what my issue could be?
You may have (3) Relays side by side in the middle of the Firewall. One is for the Fuel System. Make sure they are good and also check for a blown fuse in the Fuse Box.
@@dairleautoclassicrestorati6892 hey Gm. I have 2011 Transtar. Max force 13. Trash got in my fuel lines after changing fuel filters which I didn’t know at the time. Kept trying to crank truck. Starter went out. Changed starter now truck cranks but stop engine light is on and truck shut down. Cleaned fuel lines out. Truck starts up. Shut down engine light come on, truck shut down. Please help.
My 2014 international 4300 max force burn to must fuel anybody knows why please I need some help
my maxxforce dt after 3 days without running, it does not start, and the system has no pressure, I have to prime it, but I see that the pressure is going down the line to the tank. Can you help me?
Fuel pump ?
Also there is no visible fuel leaks only when I press plunger
The rough idle could be several things. I would not replace the primer due to rough idle. I would only think about replacing that primer if it was sucking air. And if that was to happen. The engine would die out like it is running out of fuel.
@@dairleautoclassicrestorati6892 Yeah true, im getting ready to give it another once over before I start checking injectors
We were able to take off the plunger while still installed. Three screws removed. Then replaced the two orings on the plunger with a duramax plunger rebuild kit for about $12.00 from Amazon.
Eventually discovered the problem was an injector that had a loosened hold down screw. Ended up replacing the orings on the high pressure rail, a new harness and all six reman injectors.
Purrs like a kitten now.
@@dairleautoclassicrestorati6892 I have a 2011 Transtar max13 red stop engine light. Shop said high pressure fuel pump. Changed that. But the light is still on. Help please
I wish that I could give you an answer . I have not tackle that problem before.
You based in tx??
North Carolina
@dairleautoclassicrestorati6892 😠 😡 😆 well at least I know If I have a BD there I know who to reach out to.