Thanks for sharing your video ; This is a "short term" fix / solution only but do remember that each LED draws a certain amount of current from the total available current that's applied to the globe , by bridging the gap of the "stuffed" LED - the remaining LED's will get a slightly higher amount of current through them all & their lives will be shorter than that of having all LED's working but by replacing the missing LED if possible - you'll be able to keep it working properly as intended ; the only question is to where you'll be able to buy these small SMD ( Surface Mount Device ) LED's on their own to replace the "stuffed" LED that caused the issue in the 1st place.
Everything you're saying is absolutely correct, but at least you can get a bit more use out of the bulb before it is rendered useless. Also, the dome on the bulb traps heat and causes the LED's to burn out quicker, and if you leave the dome off and drill holes in the bottom part, it will ventilate the LED's and chips, allowing them to run cooler, and giving them longer life. Manufacturers are missing a sure bet by not making a domeless LED light bulb with LED's which you could plug in and unplug as easily as you plug in and unplug an electrical cord, perhaps with the help of a simple chip puller/seater, then selling individual LED's rather than entire bulbs. I suppose that would cut down on their profit margin a bit though, and since the whole thing is about profit, they'll probably continue to prefer built-in life limits rather rather than make something which is as good as possible. There's also the question of whether consumers would buy something which looked so radically different from what they've become accustomed to using.
@@Chompchompyerded Well said! , I believe that it's all about "Marketing" too ; if every product is "made to last' - they lose out on their profits & if it only lasts a short while - then it means that we "have to" keep on buying their items ensuring that they keep on making them as a "Flawed" product.
@owlhuman I did this to one of my burned out bulbs a couple of weeks ago. It works fine, but without the diffuser on it, it burns blindingly brightly. It's much cooler, but wow! Don't look directly at it. It's brighter than the mid-day sun on Mercury.
I have 2 bulbs that were dim. I knocked one with a knife, knocking on the yellow LED squares, to get it to jiggle back into full bright. Once I got that one working, then I tried knocking the other one, but while doing so, the first one went back to dim again. Then while trying to get that one bright again, I touched the knife to a dark part and saw a puff of smoke. Now that one is permanently dark without even a bit of bright. The other one lights up very dimly when I put the two sides of a pair of rubber handle, needle-nose pliers to each LED square like these videos always say to do. But _never_ does it cause to light up all the other LEDs when you come upon the one LED that's defective. On many LED squares they all spark to life but very dimly. I don't know what your instructions are good for. I tried putting the two sides of the pliers on each LED of the first bulb and _not one_ lights up. They all stay dark at all times. So now what?? How do I fix my 2 LED bulbs???
Check the LED resistance and put that across the LEDs to test them. Don't directly short them. Most of the time, these LEDs are in series, acting as voltage dividers. Shorting one may put too much voltage across the others, burning them out.
Bermanfaat infonya. Seumpama sulit tidur bca halus "Allahulaaaaailla haillahuwaalhayyul qoyyumlatakhudu husinatuwwalaanaum" berulang2 sampai tertidur, tetanggaku tidak mau bca awal ayat Kursi itu saat sulit tidur saat meninggalnya tidak baik. Bcanya halus tapi jngan terlalu halus. Doa itu untuk pmbca yg islam.
@@electricsolution6599: I have 2 bulbs that were dim. I knocked one with a knife, knocking on the yellow LED squares, to get it to jiggle back into full bright. Once I got that one working, then I tried knocking the other one, but while doing so, the first one went back to dim again. Then while trying to get that one bright again, I touched the knife to a dark part and saw a puff of smoke. Now that one is permanently dark without even a bit of bright. The other one lights up very dimly when I put the two sides of a pair of rubber handle, needle-nose pliers to each LED square like these videos always say to do. But _never_ does it cause to light up all the other LEDs when you come upon the one LED that's defective. On many LED squares they all spark to life but very dimly. I don't know what your instructions are good for. I tried putting the two sides of the pliers on each LED of the first bulb and _not one_ lights up. They all stay dark at all times. So now what?? How do I fix my 2 LED bulbs???
@@vibhordublish9914 I thought about the same thing. Measure the resistance of a good LED and go buy a resistor closest to that value. Then solder it back into the removed LED. The current should stay about the same. It is not going to be as bright. I believe it is a series circuit. Many people in the comment section recommend leaving it open. This makes sense because of heat will be dispersed easier.
I tried to check the damaged smd exactly the same way u did in the video and the bulb gave light for a second but then other smds burned immediately ... Why???
@@Pc.Farmer Thank you for your attention .... Agree with you , but he just used a piece of wire (red) for the checking and didn't mention anything about redistors.
Though a short cut a very unscientific and unprofessional way of repair. With such repair the bulb is definitely get damaged in few days The damaged led should either be replaced with new or with equivalent resistance
I wish all LED lights were obsolete. They ruin the night sky (you cannot even see stars in a city anymore), they blind you when driving from oncoming cars and they even change the colour of items, so you're unsure of the correct colour (for people who rely on colour design). I curse whoever invented LEDs. They are just awful.
Thanks for sharing your video ; This is a "short term" fix / solution only but do remember that each LED draws a certain amount of current from the total available current that's applied to the globe , by bridging the gap of the "stuffed" LED - the remaining LED's will get a slightly higher amount of current through them all & their lives will be shorter than that of having all LED's working but by replacing the missing LED if possible - you'll be able to keep it working properly as intended ; the only question is to where you'll be able to buy these small SMD ( Surface Mount Device ) LED's on their own to replace the "stuffed" LED that caused the issue in the 1st place.
SAVE ONE BROKEN BULB JUST FOR PARTS.
Everything you're saying is absolutely correct, but at least you can get a bit more use out of the bulb before it is rendered useless.
Also, the dome on the bulb traps heat and causes the LED's to burn out quicker, and if you leave the dome off and drill holes in the bottom part, it will ventilate the LED's and chips, allowing them to run cooler, and giving them longer life.
Manufacturers are missing a sure bet by not making a domeless LED light bulb with LED's which you could plug in and unplug as easily as you plug in and unplug an electrical cord, perhaps with the help of a simple chip puller/seater, then selling individual LED's rather than entire bulbs. I suppose that would cut down on their profit margin a bit though, and since the whole thing is about profit, they'll probably continue to prefer built-in life limits rather rather than make something which is as good as possible. There's also the question of whether consumers would buy something which looked so radically different from what they've become accustomed to using.
@@Chompchompyerded Well said! , I believe that it's all about "Marketing" too ; if every product is "made to last' - they lose out on their profits & if it only lasts a short while - then it means that we "have to" keep on buying their items ensuring that they keep on making them as a "Flawed" product.
I don’t have a soldering iron so how about gluing a piece of aluminum foil ?
@owlhuman I did this to one of my burned out bulbs a couple of weeks ago. It works fine, but without the diffuser on it, it burns blindingly brightly. It's much cooler, but wow! Don't look directly at it. It's brighter than the mid-day sun on Mercury.
terimakasih atas ilmunya.. sangat bermanfaat 🙏
I have 2 bulbs that were dim. I knocked one with a knife, knocking on the yellow LED squares, to get it to jiggle back into full bright. Once I got that one working, then I tried knocking the other one, but while doing so, the first one went back to dim again. Then while trying to get that one bright again, I touched the knife to a dark part and saw a puff of smoke. Now that one is permanently dark without even a bit of bright. The other one lights up very dimly when I put the two sides of a pair of rubber handle, needle-nose pliers to each LED square like these videos always say to do. But _never_ does it cause to light up all the other LEDs when you come upon the one LED that's defective. On many LED squares they all spark to life but very dimly. I don't know what your instructions are good for. I tried putting the two sides of the pliers on each LED of the first bulb and _not one_ lights up. They all stay dark at all times. So now what?? How do I fix my 2 LED bulbs???
Check the LED resistance and put that across the LEDs to test them. Don't directly short them. Most of the time, these LEDs are in series, acting as voltage dividers. Shorting one may put too much voltage across the others, burning them out.
Save Better With Charger 5V
That is DAnggerous.. with Only 1 Cable.
Asslamo alikum sir nice
Nice.. Thanks for the trick ❤❤❤
Bro hum jesa wair le sakte use se bulb repair karne se kuch hoga nahi to
the best video ever. simple, and it works perfectly. do not be afraid withe cable.
Super 👌
So amazing
Good
Thank you
The Chinese don’t want folks repairing defective bulbs so now they’re gluing to globes to the base. They don’t just pop off any more.
Bermanfaat infonya. Seumpama sulit tidur bca halus "Allahulaaaaailla haillahuwaalhayyul qoyyumlatakhudu husinatuwwalaanaum" berulang2 sampai tertidur, tetanggaku tidak mau bca awal ayat Kursi itu saat sulit tidur saat meninggalnya tidak baik. Bcanya halus tapi jngan terlalu halus. Doa itu untuk pmbca yg islam.
😮😮
👌
Nice
Thanks, but what if you have 2 or more leds damaged? will this technique still work? Or is it only if you have 1 damaged led?
I also have 2 led damage, I thought I have to fix 2 of them but turns out I only need to fix 1. All is good now.
What if fauty LEDs are more than one ,how do you carry out test using that method?
Отлично!
Maacih
❤
Very hard to open
Good
Ok, don't do what this guy does. You'll live longer. I promise
Okee
Bhai kuch din bad fir ek led fuse hogib..
How to Repair the LED bulb Without soldering iron please say I AM intrested
You can check my channel and see other videos
😊😊😊😊
realy its working
sebaiknya chip led diganti semua
Nice Video
Thanks
@@electricsolution6599: I have 2 bulbs that were dim. I knocked one with a knife, knocking on the yellow LED squares, to get it to jiggle back into full bright. Once I got that one working, then I tried knocking the other one, but while doing so, the first one went back to dim again. Then while trying to get that one bright again, I touched the knife to a dark part and saw a puff of smoke. Now that one is permanently dark without even a bit of bright. The other one lights up very dimly when I put the two sides of a pair of rubber handle, needle-nose pliers to each LED square like these videos always say to do. But _never_ does it cause to light up all the other LEDs when you come upon the one LED that's defective. On many LED squares they all spark to life but very dimly. I don't know what your instructions are good for. I tried putting the two sides of the pliers on each LED of the first bulb and _not one_ lights up. They all stay dark at all times. So now what?? How do I fix my 2 LED bulbs???
I think I'll never understand YT music videos.
You can see my other video...
Just scrapping and soldering the perticular part , is it the proper way to rectify the fault ?
He should have used a resistance of suitable value in place of fused LED but he seemed believing in shortcuts.
@@vibhordublish9914 нет
No...but by doing it this way may outlast new bulb...just try it...and if you dont put back the top cover it will last even longer.
@@vibhordublish9914
I thought about the same thing. Measure the resistance of a good LED and go buy a resistor closest to that value. Then solder it back into the removed LED. The current should stay about the same. It is not going to be as bright. I believe it is a series circuit.
Many people in the comment section recommend leaving it open. This makes sense because of heat will be dispersed easier.
ఎలా చేయాలో చెప్తే బాగుంటుంది. Music బదులుగా
Nice one, just leave the defuser off, they will run cooler, and the light will be better.
With the defuser off, they are super bright... maybe too bright for some.
Which part of the bulb is the diffuser? The cover (the top part of a bulb)?
@@donlod322 the cover white thing
But the power is very low
THANK YOU..
Thanks!
Nam ke
Thank you
I tried this but I can’t separate the parts.
Question: how long does it take to start a house fire? :D
Sir ye jo current laga ke check karne se hame problem ta nhi hoga current nhi lagega ta
Covering wire must be used. Thank you
Munto bem costei
محمد من فاس
If you fixed like that is very dangerous, you can remove first the lamp from AC and then you can search dead led with cable and use battery
he is pakistani and pakistani always look shortcut....
Agreed.
If your driver fulte then you can't check.
Yes
Meng. Egak. Nrumum
wadul saya coba cara itu ga cala
There are new ways to do this.See me.
Speak lord. Speak to me
Good to upload videos but it can't work for an hour, total waste idea
kasih penjelasannya dong
Anyone blows on the smoke of 😅the solder
is works 😀
Is it real?
fukin genius...❤
Great, but how did you pop the top off of that bulb?
Don't think so really.far as I can see you just complete the circuit.
A knife on the edge and it pops easy off
SNIMAK STROGO ZABRANITI !!! Da nebi neko stradao !!!
I tried to check the damaged smd exactly the same way u did in the video and the bulb gave light for a second but then other smds burned immediately ... Why???
To choke my others video for solving this problem
Should have used a resistor to step down power bit
@@Pc.Farmer Thank you for your attention .... Agree with you , but he just used a piece of wire (red) for the checking and didn't mention anything about redistors.
Led bulb ko fuse kaise kre
Though a short cut a very unscientific and unprofessional way of repair.
With such repair the bulb is definitely get damaged in few days
The damaged led should either be replaced with new or with equivalent resistance
ini penjelasan kaya orang tuna wicara
I wish all LED lights were obsolete. They ruin the night sky (you cannot even see stars in a city anymore), they blind you when driving from oncoming cars and they even change the colour of items, so you're unsure of the correct colour (for people who rely on colour design). I curse whoever invented LEDs. They are just awful.
What does an LED have to do with the stars?
you are right the headlights in cars are so blinding and no one cares they should be outlawed for cars
طريقه غلط
It's not working
Ben daha pratik bir yöntemle tamir ediyorum kanalımda
Good
Chees
Hzuwg
Worng tecnic
You can watch my other video. and Different idea. Thank you