speed control of BLDC motor using PID controller

[@HarshT-dn5ug]

in order to get exact result put the value of dc voltage to be 47.89v and the value of gin to be kept to -30/pi good luck
✌✌

[@-EE_SHAIL_RAJ]

i really thanks you

[@eduardocappiello1]

Thank you!!

[@RayanMalik-ql2yj]

Thanks, it actually works by putting the value that you've told!

[@anus4444]

Thank you so much 😀

[@RayanMalik-ql2yj]

Very useful video! Thanks a lot, and good luck!

[@tejassrivastava6971]

Did you simulated? Did it work?

[@FLAMERAYYT]

@@tejassrivastava6971yup! It worked

[@stukershaw8394]

Hi could yu tell me where this truth table comes from as my model won't work as yours does, sure it's to do with truth table?

[@thoughts424]

Hi! It was helpful. Can you provide the source for truth table of the decoder used or any more sources to know about decoder used in BLDCs.Thanks!

[@saravanakumar.a]

Invalid setting for input port dimensions of 'BLDC/gate pulse/Demux'. The dimensions are being set to 1. This is not valid because the total number of input and output elements are not the same
Component:Simulink | Category:Model error
Error in port widths or dimensions. 'Output Port 1' of 'BLDC/gate pulse/emf_abc' is a one dimensional vector with 1 elements.
Component:Simulink | Category:Model error
These were the two errors poped up for me. Could you pls mail me the solution regarding it please :)

[@_035tamananabi7]

For all those who aren't getting the right output.. Keep input dc voltage low upto 47v and keep the gain block value -30/pi instead of 30/pi...this way you will get the output as 499.5

[@rohanmistry7528]

Do you have the simulation

[@abdulmanaf4963]

thanks alot bro its working😍

[@rohanmistry7528]

@@abdulmanaf4963 do u have the simulation sir

[@sunilsahare8917]

if we put -30/pi instead of 30/pi it works in matlab but is it feasible in while going for hardware work, will be useless

[@ashishshah1856]

thanks a lot

[@nsangalashi19]

In the decorder circuit, the second wire connected to the second input demux should be connected behind the NOT gate and not in front of it, the gain should remain the same, 30/pi

[@SelwynLloydMTado]

Hi! May i ask how to get the value of kp,ki, and kd?

[@techvik63]

Decoder circuit how to add truth table

[@aravindsomanath2485]

I tried,but I couldn’t get the result as you got.I think some changes you made which is not included in this video.

[@rohanmistry7528]

Do you have the simulation

[@HARSHAPOWER-xe6dx]

You are trying to do in future you will get succeed keep go on

[@rohanmistry7528]

Do you have this simulation?

[@kartik_kumar13]

don't put -30/pi instead of 30/pi. just change NOT gate at 27:34 . only apply not gate to upper wire don't apply on both the wire.

[@LingRuo607]

You are right! Thanks!

[@mustaphaaguerrab803]

please any help how she did to get the PID values ?

[@kannupriya8957]

Hi mam the video is very useful but what's the logic or truth table you are following to make a decoder at 23:04

[@danielteodoro8254]

why you didnt change the PID parameters?? What kind of methods did you use?

[@rohanmistry7528]

Do you have this simulation

[@user-gp5lo6nl4i]

podu maja than inimae ithan yen final year project uh....

[@42gopikrishnac57]

Massu vro

[@nithishs6444]

How do you import the truth table value into the model.

[@snehasishbanerjee4705]

To all, who are not getting desired output... Its decoder subcircuit is a complete mess, that's why it's not working... Get a right decoder circuit for Hall sensor anywhere from Google.. the circuit will run nicely.... After that, you can change the parameter values of PID CONTROLLER to get better response. All the best😊.

[@malisiri3883]

can you give the PID controller values

[@steffinchackovarkey5773]

Which version of MATLAB are using

[@user-rp2oh3zx7q]

Then how when we remove the pid then the result can provide please

[@nafreefirenaistam8267]

Can you do this with dc servo motor?

[@yshashi5920]

Do u have base paper ? Can u send the base paper link..

[@vrinda_theambitious]

Keep gain block gain block value -30/pi and correct the decoder circuit from czcams.com/video/irBoN1RJkO4/video.html. The Second line should be connected to not gate input instead of output.

[@hocho2278]

What is the purpose of sharing this videos 🤣🤣🤣🤣🤣🤣🤣🤣Thank GOD, If you don't want to share the values of PID, Repeating sequence 😅🤣Many undergraduate students are watching and wasting their times.

[@rohitathithya3964]

+1

[@gowtham3120]

Mam How did you paste that truth table there? 27:34

[@walmirsantos9026]

I tried too, but couldn´t the result as you got. Walmir Brazil

[@adityakale9917]

Mam plz share the simulation link...

[@zanakemaloglu1755]

same paremeters are missing, ı coundt get the result

[@rohanmistry7528]

Can i get the simulation

[@arpitsharma2324]

how you choose the value of gain .

[@rohanmistry7528]

Do you have this simulation?

[@KrzysztofDomagaa-ym8zn]

Can you send me a files?

[@supraxmen125]

I don't have the correct output even I edited it. Can someone tell me about the value of PID, Sine Wave, and repeating sequence? Thanks a lot guys 😁

[@PratheekPoojary-it8us]

👍

[@techvik63]

Mam please tell me fast tomorrow test

[@engineersdotcom3446]

results are not matched when i am trying to make its simulation

[@rohanmistry7528]

Do you have the simulation

[@naemamir678]

This video is waste of time

[@jakkavijayalakshmi3012]

I tried too much .but I didn't get output.How to contact you