Boost converter Using NE555 6V To 60V with feedback - Part-2
Vložit
- čas přidán 5. 02. 2023
- Hi Friends In This video i will make a boost converter using NE555 time ic
-
JLCPCB 1-20 Layer PCB from $2, Flex PCB from $25, Sign up to Get $54 Coupons via jlcpcb.com/IAO
PCB Assembly and 3D Printing Offer a Rock-bottom Price too.
-
Gerber File For PCBs
drive.google.com/file/d/1RQYh...
Circuit Diagram
-
drive.google.com/file/d/1Ye7z...
i made this boost converter in my previous video part -1 . but there was a problem. the voltage was not stable it starts increase until 70-80V so it was problem. and that much high Voltage is not usable for anything. I'm in this part 2 i added feedback. and now its stable and the voltage can be adjusted from 6V to upto 60V . it works amazingly. i used The pin 5 of NE555 timer ic . because the 555 timer ic has internal OpAmp That is connected to oscillator. and pin 5 is connected to Non inverting output of OpAmp . and i used A NPN Transistor to Pull the pin 5 to ground and used a voltage divider to control output voltage. when the voltage increase on feedback the circuit tourn off for neno second or maybe less . and it somehow stabilize the output voltage to a level. now that voltage can be used to power many things. and this is awesome.
if you read these all . then I want to say its very hard to make these videos so please like and subscribe for more :-)
#Boost converter #buck boost converter#boost converter simulationclosed loop boost converter#boostconverter #design and simulation #buckboost Converter simulink matlabboost converter pi controller design #inverter #12volts #5volts #24Volts #dctodc #actodc #sepic #z44n #ne555
Watch part -1 here
czcams.com/video/myDSWl5I03k/video.html
dont good! coil bazer , dont stabile voltage
Hello
I think you need to increase the frequency 50-100khz
@@Electronic_For_You in the diagram isn't 100r 2x , but the PCB is 2x 100r , 1k potencjometr 5k at the diagram is 20k please axtualise
If you intent to operate the 555 at 50% duty cycle it is convenient to controll the charging and discharging of the capacitor from the output (pin 3) across the 10 kOhm resistor. In this case you save 1 resistor and you avoid to short 1 kOhm to ground via the discharge (pin 7) and waste 1 mA per 1 V operating voltage unnecessarily.
Maybe true
Wow that's amazing
This little circuit can handle 60Wattts 🔥
Yes 👍
@@Electronic_For_You
🤯🤯🤯🤯
Cool 🔥
Nice work bro im sure this gonna be helpful 😊
I'm amazed by this circuit
You must Try!!!!
Be careful must use Capacitor 100V and Low current Powersupply.!
At first try!
Thanks for sharing
Welcome 😊
Miyako thina montuli toku👍👍👍
👍
This was an awesome video , I subscribed btw 😀
You must try 😁
@@Electronic_For_You Am going to build it today
@Creative For You pls I made it, and it regulated, but when I put a load, it fell to input voltage pls help me
How much current you loded?
@@Electronic_For_You like a motor or so
Nice 👍
Thanks ✌
Amazing
Circuit 🔥🔥🔥
I made this and it works very well. But not good with Small Inductor!
Yeas
I told to use Bigger inductor
@@Electronic_For_You
Thanks for amazing video 🔥
Welcome 💪
Ok will subscribe you. Thank for your information.😬😬👍👍
Thank you 😊
Молодец супер ! 5А это круто ..
используйте 2 МОП-транзистора, вы получите до 8 ампер. Это правда 👍🔥🔥🔥🔥
does it work under little step down environment? maybe i will use this circuit for 3s battery, i hope i can make 12v stably even though the full charged battery voltage is 12.6v.
thanks for your educational video.
Very nice project ❤❤❤
Thanks 😀
@@Electronic_For_Younext update buck and boost pwm controller converter use IC 3843
👍
Good Jobs 👍🏼
... Hobi Elektronika here 😊
Thanks ❤️
gan rangkaian ini beneran bisa bekerja kah?
@@fanless3193
I tried 100% Working!!!!!
Why not !
I share Working Circuit Always 😊
If you Have any problem always ask!
@@kalashnikov_47z thanks mate
Good
Thanks
1:50
i wonder why there is 2 resister more under the potentiometer. i saw your circuit diagram, and i'm making schematic before compositing circuit, your circuit diagram has only 100k ohm nearby 50k potentiometer. little bit confused.
And maybe i can use 100 OHM infront of the 75N75 mosfet , right?
for the last, can i use only circuit diagram that you uploaded for 5Amps output?? I checked gerber file in your jlcpcb link, there was two of 75N75 mosfet, and is there something different for output Amps?
Sorry for asking a lot. And always i feel thankful for your channel
Hello,
I recommend using the uc3843 IC. , because the ne555 is not made for boost converter,
I've tried the circuit diagram simulated using Proteus and Easyeda but why is there no change to the output with 12V input, even when I've changed the resistor variable
I never tried in a simulation!
But in reality this circuit works you can try yourself!
How did you do your calculations for this circuit? Could you please explain?
What calculations?
what is the value of the electrolytic capacitor on pin 5 of ic 555?
1nf
I have to build from the schematic on google drive and what parameters do the resistors have there besides ohms
Kilo ohm resistors
@@Electronic_For_YouHow many watts is a 1 kilo, 10 kilo, 100kilo resistor.
It can be any watt 1/2W or 1/4W
reply me sir
can i use this circuit to power my 19.5 volt, 2.1 amps laptop ?
because my laptop has no battery and i want to use circuit to boot my laptop which requires 19.5 volt with 2.1 amps.
will this work sir ? ? ???
i am using laptop-lithium-ion-celss.
I uploaded another video a few days ago !
Watch that one !
It's perfect for your work!!!!
c1 470 uf or pf? look like not same value on real board!!
Pf
Bhai iska PDF File do na jisse mai isko bana saku
Follow the part 1 diagram then part-2
@@Electronic_For_You Ok Bro
IRF1010E TO220
Power 200 W
Voltage 60 V
Current 84 A
This mosfet will be good if I replace 75n75 with it
Yes
It works too
What source did u use as an input .is it battery or .. ac
DC 6v - 12V
Can we use mosfet Irz series
Yeas
mosfet as Q1 is Bc547???
I'm sure you didn't watched full video. Everything is written on diagram. 😄
Sir in ur diagram one of the resistor's specification is not given. So can u plz send me the ohms of it sir rn
Gate Resistance of MOSFET is 10 To 100 ohms
In the video, there is a ceramic capacitor, how much is the ceramic capacitor worth? Where is the ceramic capacitor connected?
470pf to 1nf
0.1$ each
if I supply 12v, do I get 5v at the output and if I change the input voltage to e.g. 1.5v, do I also get 5v without adjusting the potentiometer?
I think you don't have proper knowledge about the Boost converter! It's not how it works! A boost converter can only increase voltage higher than input voltage!
@@Electronic_For_You I didn't think so I knew he was just lifting but forgot with this example. Let's say I set 20v for the output then giving 12v, 9v to the input, the output will always be 20v. What if I don't use a schotkky diode but a regular 10A diode
@@Electronic_For_You I can use the LOS ESR capacitor
Yeas it remains the same voltage!
You have to use a High Frequency diode or the diode will get Hot and burn !
It's good to use a Low esr capacitor!
@@Electronic_For_You I found on a popular site in my country with various things 1n5822. it is a diode 40v 3A if I connect them for example 3 in parallel I will achieve 40v 9A?
May i use 3.7 volt for the input??
It works from 4.5V . Minimum 5v input
Why is the mosfet hot even though it hasn't been loaded yet?
🤔 is it consuming current and how much?
after looking for the cause finally the circuit works perfectly, this is very useful... thank you...
I'm happy to hear it worked 😊
Thanks for watching
Don't forget to subscribe for more ❤️
What resistor for mosfet irf1010e?
10-100 ohm
@@Electronic_For_YouHow little came out of the information in the catalog note?
How many watts of real output can this circuit provide?
40-60W
Can this circuit works at 5v or has to be 6v input?
MOSFETs don't switch on 5V so 9V input is most efficient
@@Electronic_For_You thank you for answered.
We can change it to lower gate mosfet voltage like 160n03, 90n03 as its threshold only 2v-3v.
🤔
You can try . But i recommend using UC3843 ic i have another video . Recommend watch
I followed the schematic like the video but the feedback doesn't work, please help me, I use 2n5551 instead of bc547 because I don't have it :(
How it behaves
Please can you explain so i can give you advice!
@@Electronic_For_You I followed the diagram you put below the description, when there is no load the output still increases the voltage to 40v but when I supply the output load about 40w the voltage is only 27v maximum. I tried increasing the input voltage from 12v to 13v the output also increased.
Is it adjustable like mine ?
Can it adjust the voltage normally?
Or stuck at 40V?
@@Electronic_For_You yes but only when there is no load. On load it gets stuck at 27v
Oh
Can you input 12V and get 24V ? And load it?
I am not able to get the inductor 80uh so what can I use instead
Inductor from Computer Powersupply
Can u plz tell me the ratings sir
Use A Iron Powder core and make 10 to 15 Turns 1MM copper wire
Or
You can use 100uH inductor
Ok thank u sir
The circuit in the picture is completely different from the video. Even the capacitor is wored in the wrong polarity.
I used different components because i don't have some components
@@Electronic_For_You No, that's not how it works, you can't of course wire a capacitor the wrong way, it will blow up. And no, even with different components you can't connect it like that. I suspect this circuit is not your design since you don't even have made any calculations.
How many amps can this circuit bear?
5 Amps Maximum
@@Electronic_For_You what do you mean by maxium ? isn't the amps stablized ? then what is the minium ?
No
The current isn't stabilized. It will give how much load wants
Hi. I want to do a dc to dc boost converter with feedback for project. Howcan i communicate with you?
You can just Follow the Circuit Diagram!
Its simple
Sir what is the name of the component (blue one )used to measure output voltage
Ang also for input
You mean Input Terminal?
Are you talking about That Terminal with screws on top?
Yes sir that one with screw on top
The name of that component is *Screw Terminal Block*
I have tried this circuit and it works if not given a load, when given a load the output voltage of the circuit has a voltage drop so that the output voltage is the same as the input voltage, why is this?
I think your inductor is not right!
I have used an inductor as recommended which is 100uH
Hello try using Bigger core and higher inductance
Is the inductor you use worth 100uH 3A?
Try using 600uh+ inductance
sir your work is great please whould you like to help me in designing og boost converter whose input is 6V and f=30KHZ AND DUTY TIME IS 0.7 And Resistor value is 5 ohm with 555ic
Ok, but whare is 5 ohm resistor you want to connect
At load bro
And output ripple voltage is 0.5
Have you built it?
No sir these are the given data
How much is the resistor in the gate worth?
10-100 ohms
@@Electronic_For_You how much is the 2 capacitor electrolytes and 1 capacitor ceramic worth?
Everything written in circuit diagram
Sir can I use ln4007 instead of fr307
Will it work sir
You need to use a High Speed diode FR107 can be get from old cfl lamp ... But its only 1A maximum and FR307 Is 3Amps
Ok sir that means ln4007 will not work right
1N4007 may work but after a few minutes it will get damaged
Ok tq sir
THIS CIRCUIT IS NOT WORKING. I HAVE TRIED IT THE INPUT VOLTAGEIS SAME AS OUTPUT VOLTAGE SO IT IS NOT BOOSTING.
Is your Ne555 timer oscillating?
IT IS NOT OSCILLATING AT ALL
Make a oscillator first then use output to drive mosfet and use control pin for feedback 👍
the MOSFET becomes too hot once turn on
Something is wrong!
Maybe your frequency is too high try decreasing it to 50-60Khz
Ampere ?
Upto 6Amps
I am confused with the value part no of circuit diagram....haha
Follow the video you will found everything you need!
And its 1000% working circuit
hello sir
we tried it but the voltage is not increasing sir . why is it so
First check if the ne555 timer outputting pwm?
But how can I sir
Do you have a multimeter
If yeas ... Select Hz option and put probes on pin 3 see if you saw some Khz value if not then its not working something is wrong connected
Ohh ok sir will check it once
Ok
Sir can u plz send me the components details I want it for reference
All components are written on diagram
@@Electronic_For_You ohh thank you sir.
What could be the advantage of adding feedback system sir ?
If we add feedback The output voltage is stable
Bro second boad circuit diagram 😊
In this circuit u useing 12v regulater bro
U r from bro
This is a boost converter
9V input output 12-30V
Bro can I get 12v input and get 54vdc in this circuit is possible
For ro motor
resistor look like 10k not 100k
Follow that the screen says its fine tuned for everything. You should use what i say not what you see.
Not working wast off time.
Yeah ,
Because you failed to make it
are you a cheater? what is bc547? mosfet or Transistor!!!
Are you blind?
What do you mean by cheater?
Mind your language!
Do you know how to read component symbols, Rana?
Sir can I get ur Instagram acc .I want to get help from u regarding this vidoe
Just comment on the video and I will reply! No problem
Ok sir.