Hi. Thank you for uploading such a helpful video. It was very interesting to see whats involved and I greatly admire your professional work. How many hours would be a fair estimate of what is involved including strip down of the head to allow for it to be skimmed ? Thank You so much.
Be careful starting an engine with no coolant if you’ve fitted a new water pump. The seal on water pumps is a special type and needs coolant to lubricate it. If you run it dry when it’s new it will chew it out and the pump will leak straight away or very soon after. I learnt this the hard way….
When you put the fuel pump, did you set the timing on it? If you don't you are liable to strip and snap the cam belt over a period of time. There is a mark on the drive gear on the pump, that must be aligned with the mark on the casing. Goes in when the cam shaft drive strocket is locked in place.
@@ssss-df5qzthis pump is timed. It have only one piston. Easy to recognize, if there is that funny gearbox between CR pump and head, you should time it.
Je hebt hoop ik wel de timing belt in de juiste gaatje vast gezet en de hoge druk brandstofpomp met de diskette case op de juiste puntje afgesteld? want als je dat niet doet kan je een fibrillatie krijgen in je nokkenas en die geeft het door aan je distributie riem waardoor je riem binnen 1000 km de tandjes af kunnen klappen. PSA waarschuwt daar ook voor. Zal niet de eerste keer zijn en vaker gezien namelijk.
Hi, Can you support with tightening torques and specs or service manual? I am working on engine overhaul and I cant find seals for lower crankcase in local shops. Thanks in advance.
Hey man, Do you have any memory how does the non return oil valve on the head goes in ? There’s a red membrane and I don’t know which way it goes as the machine shop removed it and didn’t put it back the way it was …
Hi. Thank you for uploading such a helpful video. It was very interesting to see whats involved and I greatly admire your professional work. How many hours would be a fair estimate of what is involved including strip down of the head to allow for it to be skimmed ? Thank You so much.
Very professional job,,,,
Thank you 😊
Brawo. Super robota!
Be careful starting an engine with no coolant if you’ve fitted a new water pump.
The seal on water pumps is a special type and needs coolant to lubricate it. If you run it dry when it’s new it will chew it out and the pump will leak straight away or very soon after.
I learnt this the hard way….
When you put the fuel pump, did you set the timing on it? If you don't you are liable to strip and snap the cam belt over a period of time. There is a mark on the drive gear on the pump, that must be aligned with the mark on the casing. Goes in when the cam shaft drive strocket is locked in place.
These pumps aren't timed or phased mate. The cam drives gears through a little gearbox which the HP pump bolts to.
Dat dus want het zal niet de eerste keer zijn waar dat gebeurt. PSA waarschuwt hier ook al voor.
These pumps are timed, they will strip the teeth on the belt eventually
@@ssss-df5qzthis pump is timed. It have only one piston. Easy to recognize, if there is that funny gearbox between CR pump and head, you should time it.
Pompa paliwa powinna byc ustawiona na znaki po ustawieniu rozrzadu najpierw a potem pompa
dokładni tak
jak nie ustawił to rozrząd wytrzyma max 10tys
Amazing job. Well done.
Nice clean job 👌👌👌
Je hebt hoop ik wel de timing belt in de juiste gaatje vast gezet en de hoge druk brandstofpomp met de diskette case op de juiste puntje afgesteld? want als je dat niet doet kan je een fibrillatie krijgen in je nokkenas en die geeft het door aan je distributie riem waardoor je riem binnen 1000 km de tandjes af kunnen klappen. PSA waarschuwt daar ook voor. Zal niet de eerste keer zijn en vaker gezien namelijk.
Hola amigo , consulta los grados 220 , se aprieta total o por separado los grados , gracias
Cześć, dobra robota!
Po jakim przebiegu była ta jednostka?
Jaki problem się pojawił, że została zakwalifikowana do remontu?
Nice, how much do you charge?
Hi,
Can you support with tightening torques and specs or service manual? I am working on engine overhaul and I cant find seals for lower crankcase in local shops.
Thanks in advance.
Hey man,
Do you have any memory how does the non return oil valve on the head goes in ? There’s a red membrane and I don’t know which way it goes as the machine shop removed it and didn’t put it back the way it was …
Approximately how many hours did this take?
Good few days probably
👍
Hi Julius. Is this video available at normal speed please? I have this job to do on my van and the disassembly is a bit quick for me to follow :)
Unfortunately no it takes about 3 working days to do so I was recording mostly in time lapse from the beginning.
how did you get the injectors out? mine are seized up
Didn't even time the fuel pump
vous avez fait un grave erreur de calage pompe injection 1000 km casse courroie distribution et arbre à cames