TP4056 module modification for more lithium Batterys
Vložit
- čas přidán 31. 07. 2024
- TP4056 module modification for more lithium Batterys.
This is experiment only but you can try. Because this was working.
Components used in this project:-
1. TP4056 Lithium Battery charging module.
2. TIP3055 Transistor
3. 56 Ohm 1W or 2W
4. 1K Resistor
0:00 - Circuit Assembly.
2:08 - Testing.
4:43 - Testing 18650 4 Battery's.
#tp4056
#diyelectronic #tp4056_module #batterycharger #18650 #homemade101
DIY Power Inverter 12v to 220v : czcams.com/video/K-gSJNiheYI/video.html
That 0.5A is current drawn from the 3P battery due to equalizing its voltage to a 1P one. This is why the current goes down, the 3P battery become slightly discharged as it slightly charges the 1P one. Furthermore, that transistor end up in saturation (due to heavy base current) connecting the B- (collector side) to the ground (emitter side), which does virtually nothing to the charging current, because charging current still goes through TP4056, because this IC regulates the current at the positive side. Changing that programming resistor to 1kΩ increases the output current to the 1.2A, which is kind of unfortunate as the TP4056 is rated to 1A max. This modification is nothing than a nonsense from its beginning to the bitter end.
thank you
@@NikiBretschneider nice! that was my thought from the very beginning. You confirmed it, thanks! Absolute nonsense
One cell of 4.2 v
How much max current we can give?
@@NikiBretschneider yeh!! Your right 👍👍👍👍
@@NikiBretschneider HI. donde te puedo escribir?
Hi, is it posible to mod drone remote control so it can yaw smoother?
yes,.. you can try it
Wow! That’s cool. If this could be done , may I know is it possible to do one mode similar to make a 3S bldc esc into 200v bldc esc ? I didn’t see anyone doing this yet. Thanks ❤
welcome. try
nice but how to charge them when they are in a 4s configuration?
This connection is not correct. If so, we should do a separate battery charging by banning with a 4s balancer circuit. I made this as a test for this module.
@@homemade_101 I was considering using a NC relay for the 4s and pull it when the charging circuit activates but then i'm not sure if the relay will fail open or closed and that would be a fire hazard. also considering i wish to use it in a battery back for my old hammer drills there would not be room for the 3 high power relays that would be needed. I could use a A triple-pole switch but i don't like manual control especially if you forget then you fry the system.
من العراق احييك ايها الانسان البطل فعلن لديك ابداعات قيمة شكرا جزيلا لحضرتك 🌹
thank you and welcome
@@user-wh1hu6sd4u Что за каракули ?
😂😂😂 5amp not 500 mah only😅
Ignorance is visible.
Зробив зарядку на 0,5 ампера🤷
yes i thik battry was charging
Co to je? To máte v Indii nějaké nové hodnoty pro Ampery. Toto je velký fail.
okey
Multumim,bine venita inovați,merita abonat
❤
Bucurați-vă și bun venit canalul meu.
О мой индийский друг! Я сначала не узнал тебя в перчатках. Когда пойдешь в майкрософт работать?
😂 Какой смысл ставить транзистор пипец😅
Вроде как усилитель тока ?
the ic max current output is 1 amp only.theres no way this could boost current output.. cant full everyone though
full everyone
Dear you are creative. The first question, what is the benefit of the 1 kilo resistance? Why didn't the blue LED light up after the complete charging? Thank you.
A carbon film is used because the SMD resistor burns when a large current is passed. It will not turn blue because the batteries are not charging at the same time. A balancer will be used for this.
means that after the charging is complete, it turns blue and thank you
@@hanymagdy2095 welcome
Now this board 2amp?
yes
Not work. TP4056 out 4,20V - 0,65V Base = 3,55V out insufficient charger
what
@@homemade_101 you are a fraud
These TP4056 boards cost 1.5$ for 10 of them, but 🤡 "forgot" to measure voltage on cells after current fell to 10% of nominal.
yep
ایده بدرد نخوری بود نیم امپر 😂😂😂
Very good First time i saw a real video on this topic on youtube.
thank you bro
Nessa configuração esse transistor não está servindo para nada 😂😂😂😂😂😂😂😂😂
ok
what the purpose of this? to increase the fast charging?
Stop burned the module
@@homemade_101 thank you for the reply. this is good idea to stop burning module.
Carga lenta
yes sorry
i'll tray it in my project to
good luck.
💯💥Good job
thank you
Μπράβο πολύ έξυπνο. Συγχαρητήρια.
thnaks
И нахера там транзистор если все всеравно идёт через микруху, она и ограничивает ток, максимум может дать 1А заряда. Читай даташит и схематику изучай тормоз!
sorry
Последовательно с микросхемой еще транзистор. Ну да смысла от него нет. Это наверно если шунт в его цепи ставить, который микросхема будет анализировать.
Sorry brother it is taking current more than the cell's limit.
In this way you are killing that battery.
Can you limit the current below 500ma
thank you
Super❤
thanks
??????????????????
why
Thanks 🙏
welcome
everything he did makes no sense. You could just hook up the rest of the batteries
yes you are
Get some real knowledge 😂😂😂😂😂
😄