How to RESET your Android box and UPDATE FIRMWARE using ANDROID RECOVERY MODE
Vložit
- čas přidán 20. 10. 2018
- Lots of times simply RESETTING your box back to FACTORY defaults will get you up and running again. When you do need up load Firmware, here are a few things to be careful of.
- Věda a technologie
Brilliant video, 1st time I've had it explained in easy to understand language
This is a great short video on the fundamentals of programming these Android TV boxes! A+
Well explained tutorial Peter, clear, simple, and straight to the point. Thank you
Great instructional video in an easy to understand format. Thanks.
I know this is old but, I would not be looking if i did not have an old box. I would like to commend you on your ability to have told those of us that being smart and not doing stupid things is good in many cases. Thanks,
Peter, very good video on the power supply I have two H9 Pro+ boxes and have had to replace the power supply on both. Thank you for all you do us.
Yes, whenever the problem seem to move around it is usually the power supply. I had one with flickering video the other day, I tested the power supply and it was way off under load.
@@PeterC408 First thing i did was buy a 5A/ 5000 ma New supply. In 3 years never anymore power supply fail! Thank you for all your post! But the OEM power supply is a Fail/problem waiting to happen. Bet a lot of GOOD boxes are trashed over a bad wall supply. It's not always works or dead. I seen voltage swings and low MA output. If you add anything to the Box the supply is Maxed out. As with anything if you run at 90%+ of capacity it will not last long.
Very knowledgeable thank you and make some more movies like these👍
Great video sir! I just wanted to say It's far easier to utilize adb and fastboot commands via terminal in Linux or even cmd in windows to install updates. Adb sideload is drag and drop and most Android oems offer the updates that can be flashed through two commands
LOL. Think about it. how long would it take to explain ADB, what it is, where to get it, how to install it and how to use it. The explain Linux or Command line. Then say "easier" again. LOL
I wish I found this video before I bricked my box. I factory reset my device only for it to get stuck on the boot logo. Unknowingly I went and flashed a firmware to "fix" the issue. Great video - learnt a lot
I just did the same thing. 2 boxs stuck in loop. And i just moved in and wanted the 65 inch smart tv behind it will be getting put in my bedroom i guess.
Have a matricom 3 g box stuck on boot and a hvkla with supposedly 6 ram and this fancy rockchip 3133. It was the 1st to go. Lasted maybe 10 months. I think firestick is the way to go now
But i dont know much. I still wasnt my express vu back
mine is stuck on the logo screen how do i fix that
Hi Peter, thanks for all you do for us. Can you make a video teaching us how to download the Extended Info line? Thanks 🙂
Peter you are the man👍
Excellent video sir! Thank you for the referral from the other video too! This is very helpful.
"i DON'T FEEL SO GOOD, MESS AROUND WITH MY SPINE" Hahaha that's so funny but it does make us understand.. just because it's not working how we wanted doesn't mean you can mess around changing everything love you videos..!!congrats
This video answered a few questions I had. I'm still looking for information on resetting a ZTE ZXV10 B760H. I haven't been able to find any button on the motheboard, but there are jumper pins. Don't know what to do.
Peter,
This video of yours really saved the day for me! Following your instructions I managed to recover my son's android TV box.
Thank you Sir! God Almighty bless you, man!
Glad that I could help and thanks for watching!
Thanks, your video helped a lot after struggling with Androidtv logo
Have Nvidia but great info to pass on to my co-workers thanks again
Did you see this one about running Plex Server from your nvidia shield? czcams.com/video/w6vYPgMjueI/video.html
Great video again really helpful
Excellent information...thank you
love the way none of the questions posted are answered! taking care of your community and subs...good job....lmao
I try to answer them but with over 500 videos to date.... some can slip through.
Thanks a million Peter. The box is working fine now. Your video and explanations are excellent.
GREAT! Thanks glad that you got it to work.
You're definitely a life saver.. Well detailed video. Bless
Glad it helped.
Peter Thank you, I tried updating my android box and bricked it. 2 minutes listening to your video I am up and running again, Not trying the update thing again
Glad that you are back in action!
Great video Peter. I have a Mecool BB2 Pro with 6.0. How do i upgrade to a new firmware?
Love watching you! I learn a lot!!!! Ty
Thanks for your hard work
Excellent presentation. Ty
hi sir....if we already press the reset button and plug in power but the Box didn't go into the Recovery Mode, what could be the problem ? ...the screen stay black and twitching....looping...
Thanks for the tips. I just tried to do a reset on a X99 Mini (stuck in splash screen) and it doesn't work - pressing reset does nothing - just a blank screen and this is a new box (only a couple o months old). Tried the same in my old box and it works - so, I know I'm doing it right.
Is there any other trick to try to reset the X99 at hardware level? I'll open it for a look-see, but I suspect I got myself a new paper weight.
Thank you Peter, this is a fantastic video... I have one question, although I was able to enter recovery mode the system will not allow me to push factory reset when pressing the enter button. What can I do?
Press the "Power" button on the remote instead of "Enter".
I snip the point off of the toothpick with pliers or side cutters. It's a lot more comfortable and less awkward to hold the button in.
Good one. Thank you
Thank you very much !
You do know your goin to get some dafty trying to run his android box of a Micro wave lol
Excellent teaching skills
Thanks and welcome
Cool. I have a TX3 Pro. Can I use the same firmware as the TX3 mini? I can't seem to find any firmware for the TX3 Pro
Cheers Peter another great video 👍
Hi Peter, thanks for your ever educating video. I am curious to know if there is yet an Android 8.1 for my H96 pro + box for upgrade?
I do not know of such a release nor do I expect one. Most Android boxes are designed for a particular OS release and never intend on upgrading... You get what you get. Nvidia and Amazon are a bit different... they released a marketplace where they hope to sell you things... like movies, games and channels. For that reason, they keep updating the OS to control the user experience and make their support lives easier. H96Pro+ is only hoping to sell you a new box when you want to get one... they have no incentive to keep you up to date.
Thanks Nice to teach we learn a lot
It's my pleasure
Great video!
Im curious,have you heard of sny firmware update for the h96 pro+? Was agreat box in its time, but havent found any official good update since late 2017!
Did you ever find anything? I've just turned my h96 pro stick on and stuck on Android 7.2 and can't update past that
I'm getting the fire stick 4k for Christmas so no more cerseing my old box.😁
Great tutorial.... Buzz should point XPL3900 Stuck in boot customers having difficulty to your site....well done.
Anywayt you can do a video on upgrading the Mecool BB2 Pro to 7.1 if possible
New to the channel Pete looking to gain some great knowledge
Great video. Keep it up.
Can you please make a video on installing Dolby Atmos in Android TV box and solving low sound problem in h96 mini
interesting video and sense of humor!!!
Awesome Video, Thanks so so much
Hey Peter can you explain what those other choice's on the list mean and if they would ever get used.
Great video. Thanks
Hello Peter, would you know how to upgrade the firmware of T9 to version 9 pie. I would really appreciate the walk through.
Tks for replying
V nice explained thanks alot bro
Thanks and welcome
Hi Peter, I have two identical Android Box T95ZPlus and I've downloaded the TWRP image file for this model. When I boot in recovery mode with one of the boxes with the file on a SD card it brings me right into recovery mode where I can perform a BACKUP, RESTORE, WIPE, etc........ When I try to do this on the 2nd unit, it will not go into recovery mode at all, stops at the model's LOGO screen and just stays there. I remove the SD card with the Recovery.img file from this unit and now, holding the reset button and powering it up gets me to the Android Recovery mode but not the same as the first. This one brings me in to the Recovery where my choices are: Reboot System Now, Reboot to Bootloader, Apply Update from EXT, so on and so on. All I want to do is be able to do a backup of this second unit and restore it to the first T95ZPlus. It seems with the 2nd unit, I presently can't find a way to create a back-up of it. THANKS in advance for your help or anyone else that can shed some light on this.
Thanks for the Info, I had Always wondered about this, as I have a Box that is Android 6.1 and I have been told that I can upgrade it to 7.1 or higher but it will cost me $$$$$.
IMO I would think that these boxes "Should" be able to upgrade the OS like any PC/Laptop.
I also have a Android Tablet, that I would think should be able to be Upgrade able as well. Know knowing this about the boxes, I will look harder/smarter into that too.
once again Thanks for this info and a great Video as always.
In my experience you can usually get 1 upgrade on the cheap Chinese boxes and even then it's not coming from the manufacturer. It's possible your Android 6 box was being sold as Android 5 last year and they've already done the upgrade. Just like with phones there comes a cut-off point for upgrades.
thanks
Excellent video
Peter I’ve got an old pine64 what can I do with it. Maybe something for the kids
Hello i just found this and did sub, since you have many points that you covered well.. just tell me how to enter recovery mode in X96 min Tv box, since all methods i have tried wont work.. i am IT person so i even opened it cause it is strange that damn device wont go in recovery...tried to flash it over AA OTG cable and over SD card, but damn recovery mode wont start.. pin is inside AV hole ..
thanks,.
Thanks for the information on how to make the android TV box come back to life again. Please, I also have the same issue and I have tried your method but the box was not coming up. Please, any other suggestions? The OTT Android TV box is X88 pro 10.
I followed your solid instructions. Once reboot done after factory reset, now in never ending loop that cannot be interrupted by mouse, keyboard or remote. Any suggestions please?
God , I hope you speak chinese !!! because, I think I can learn from you in just a week !!!!!
Hi and thanks for help me with some issues with Android and now I ask help to boot a t95 s2 as soon and turn on stays on android tv and the logo and I try to reset but don’t work please help
Hi Peter,I have a H96 Max ulta hd box,I can not get the boot logo off the box,have tried to Reset.So I can not get the anything on my tv to try and reset.Basically I can't get to the state bit.Do you have a video where I can try and reset it by reseting the box with firmware.Thanks.
Alright, I know this isn't exactly an Android box, but it probably functions exactly the same.
One of my phones is full of trojans (my brother was pretty dumb) and factory resets aren't enough to erase them because the system files got infected. Is reinstalling its firmware and switching to stock Android a good idea?
hey peter i have a t 95 max 16 gig it kicks me off hard to go to settings got to keep unplugging it tried the pin and it wont reset where do i go from there dont use that box too much but i like it its pretty fast thank you...
Great video
my box stuck on the logo. resting it came up with (fail to mount cache I/o error) and doesn't reboot. now I have another working box (twin the broken one) can I download the firmware to an sd card from the working one and install it to the broken one?
I installed ATVXperience on my s905W box then i installed all my popular software on box made backup then installed master back up to 5 different s905w boxes , to my shock all 6 boxes now share the same mac id, not WIFI MAC but lan mac id im was not aware that this would happen and not sure how it happened reached out to ATVXperience havent heard any suggestions from them, if i can find s905w firmware from manufacturer maybe that might reset mac back to original state please help if you have any ideas
thanks
Off topic. Can we get a review of some new builds? I can't seem to find one I like for my firestick since team zt went down
I really like the KODI NoLimits FireStick Build, for the FireStick czcams.com/video/Ds32ZXuuIVk/video.html
hi peter ive a t95q andriod box the it is powering up but the hdmi signal is not being recieved ,i know its not the cable as i have the same boxin another room, i tried the toothpick and nothing am i doing anything wrong thanks
Hi, good day i have a s10 mini box, its wifi auto turn off, and when i try to restart it only stay in restart logo and didnt turn off at all, is it a software or hardware problem? Thnak you
Oh wait... so I just factory reset and it should all work again? I’ll try 😂 sorry I didn’t read the description box
Hey peter any other way to reset..stuck on mi logo on my mi box 3...got to factory reset screen...I reset it started reboot after recovery...and still freezes on mi box logo? Thanks for all your info...PS. All started after the Oreo upgrade..
Hi Peter, great video, very good info, thanks, i own an MXQ PRO 4K, i followed the process, erased data for factory reset, but does not boot, can you help please
How did you go on recovery mode. ? I am pushing the reset button on Av hole, then plugin the power but the box doesn't show any recovery mode
Does anyone know the size of power supply plug size? I have a few box's and and they all seem to be the same power supply plugs. Is it a 5.5mm/2.1mm are a 5.5mm/2.5mm. The original power supplies seem to be about the same and cheaply made. I would like to try a slightly better made one and hopefully it would last longer.
Afternoon/morning Peter,
Great vid and thanks. My issue goes a bit deeper and wondering if you have any advice..
T95z plus No.1: we had two power cuts in quick succession and TV box is now stuck in perpetual 'boot'. Presents the animated logo, but nothing else.
T95z plus No.2: purchased new TV box and low and behold, electric switched off (doing a bit of wiring in the house) and the new box was also stuck in 'boot' and some times, no display on the box at all. Just the blue light from inside.
By dumb luck, T95z plus No.2 went into recovery mode after powering it off/on may times. I was able to factory reset and all is well.
I decided to see if I could save T95z plus No.1, but I am stuck. I only today discovered the reset button in the AV port, but when I press and hold while powering on, the box doesn't boot at all and has no lights. Just a quick flicker of the hex-halo when the power is inserted.
I have tried the new power cable and variations of when I press the reset button, but no change. Just stuck at 'boot'.
Is it bricked beyond repair?.
Thanks again and love from Ireland
Sorry for the long delay, we had a death in the family and time was lost. The T95z looks like it does support a new build of Android 12 but it is an older processor. How do you have so many of them? Try holding the button when applying power. Changing power supplies is a good idea. If it doesn't work, it could be just dead. There are so many great boxes. Make sure to get one that will keep updated: Roku, NVidia, Amazon. Those will work for years.
Hi, i have x88 pro 13 ultra hd 8k, after restarting it, it always needs to get factory reset after restarting. Can you explain how to solve this problem? Thanks!
My MXQ Pro box doesn't have a reset button/hole?
In TV box to go to android recovery we have to press and hold rest button and insert power cable to TV box .....after 10 counts release reset button? We will get the recovery options on screen? Correct?
I am unable to find firmware for a easytone T95Z max. Can you help me find it?
I tried to do your reset method fro an android box Mx3 but it won't work and it won't go to android recovery mode. When I try the pin reset and holding power the red light jut turns of and will go gray.Can you please help me?
I have a old Keedox MX3 box running 4.4.2 I wonder if I can upgrade it. Found the reset button in the a/v jack.
As we went from Android Jellybean (4.4) to KitKat(5.0) the requirements changed a lot. Jellybean was popular and long lived. When KitKat came out many of the boxes were left behind. I would just get an upgraded box, an Android TV and here's why czcams.com/video/_ONZkYWyhqM/video.html
Hi Peter I have a worldmax tv box which I have reset got it going but after a short while it reset itself and now even after reset it goes back to the old setting, how can i upgrade box.
This is great, Peter. I have an Nvidia Shield tv box with various apps but I don't know how to update them. Asked on their forum but they get a bit precious about using 3rd party apps. Any advice?
Sure. The easiest way is to go to the Google Play Store and look up the installed apps. When you pull them up, they will show you if there is an update available. If so, just hit update.
Oftentimes I have got them through apk. Is it the same process?
I have an issue with a MXQ PRO 4K box. I have the exact firmware that is meant for the chip, i burn it with an IMG maker to an SD card ... But the device never reads anything. Always gives a failed to load error when I click on Update from SD CARD..?
Hey I have a buzz xpl3000 I did a hard rest now my server setting keep saying" please contact your provider to register this device" my subscription is active and my Mac address is the same. When I try to connect I get that same message. I even added a new server and it's the same thing
I cant get to that menu on my TX6 that is stuck in boot
@Vipul Ahir Same problem here with my X96
Hello Sir I just have one question I have a H96 max box for some reason Google play store and play service have been deleted from my box every time I factory reset they don’t come up I install new ones but it’s not compatible for the box any ideas what should I do
Hi Peter, i just bought H96 plus pro S912 Amlogic 3/16gb. What happened is that i only installed the superuser snd when the box asked me to reboot i did snd after that it stuck in logo. I tried the wipe data and clear cache but wont help. I also tried the same firmware on SD but it wont read the file. The file is .img but aml is on the front. Much appreciate if you can help! Best regards
Hi Peter, do you have a link to a power supply that works with Tanix boxes? I have the first one you reviewed with Alice, and I really like it alot, but the power supply no longer works. Thanks
It is best just to look at the plug, voltage and current and get a match for that. You need to match the plug (fits) and polarity (99% center positive) and the voltage. The current (or amperage) can be over but needs to be enough. Usually for these boxes we are looking at 5V, 2A but 2.5A is fine ... it will only consume the current it needs. In the old days, we could go to RadioShack, but that is gone now. The plugs (usually barrel plugs) are measured in millimeters (usually between 2mm and 3.5mm). Try a new power supply but here is a reason you may just want to get an AndroidTV box czcams.com/video/_ONZkYWyhqM/video.html
X96 Max I found the reset button in A/V port. Unplugged the power and pushed the rest button and held 10 seconds and plugged in the power. Held the reset 10 seconds after the power cord was installed and released. The logo came back on in the frozen state ???
Frustrating.
What else can I try???
What do I do if I am stuck on the recovery screen. I have no idea how my Android tv box restarted on this recovery screen on its own, I did not touch any rest button or do anything differently. And after googling several links I have tried to do the factory reset but then I can’t get past this it does reset and then I can’t get out of this screen no other screen come up or I can’t get into any kind of other boot up screen. Please help. I am definitely not the most technical savvy so I’m hoping that it’s something I can try and repair myself that is not too complicated
I did something wrong, I have tried to update firmware for my Mecool BB2 Pro TV Box to Android 7.1.1 that was installed on an SD card, failed massage while updating under android recovery , clicked on reboot system now then device toped working (only the blue power led on is on without showing anything on screen and tried to press the button but nothing happened )
Thanx, mate!
Hi, I have a t95z plus.
How can I reset the restriction profile!
It would work if in place of native box recovery you installed TWRP recovery and tried to install the new system using this new recovery method
I did reboot my nexbox A95X 2 times , and down loaded a app again but the sound is very bad and the movie stopped. and the tv flashes and sound crackles. After I rebooted it, some of the icons got change to different apps and will not let me go to settings and when I do the the tv screen still said invalid format... Any ideals ? thanks
I've an android box here, and the reset button has no effect. It still bootloops. You see a split second of some yellow text in the bottom left but it's back to boot logo
Useful video, Peter.
Hey Pete, I have a Monsterbox X1 Max. I turned it on this morning and have nothing but a green screen. Any idea what's going on with it? Ty.