Make A Blind Hole Bearing Puller | DIY Inner Bearing Removal
Vložit
- čas přidán 27. 03. 2023
- Today I will Show You an Awesome DIY Tool Idea. I Make A Inside Bearing Puller. It Is a Very Useful Tool For Fan type 6201 - 6202 Size bearing removal. I Hope You Enjoy This Video. If You Like This Video Then Click On Like And Subscribe to My Channel For More New Videos.
►Subscribe to my channel and don't forget to click the bell 🔔
/ mistrymaketool
►My Favourite Project Videos:
• How To Make A Spot Wel...
• How To Make A Bench Vi...
• How To Make A Angle Gr...
• How To Make A 9 inch D...
Visit My Official Website:
mistrymaketool.com/
Social Media:
Facebook Page: / mistrymaketool
Instagram: / mistry_maketool
Pinterest: / _created
Thanks For Watching...
Hit the Like & Subscribe Button...
#mistrymaketool #diyproject - Jak na to + styl
Many people commenting "use grease, bread" etc.
That method is useless if the bearing is not sealed or the cavity has an oil gallery etc.
Thanks for the video, I finally removed a stubborn bearing today using this as a basis for a design.
You can take a rod the size of the inner hole in the bearing, then pack the hole with grease. Place the rod in the hole and strike with a hammer and the grease will force the bearing out. Old mechanics trick!
Or bread will work too. Although this is a good tool for when there is a hole behind that the packing trick won't work on
That's right and lot less work than all that.
Was thinking the same thing, but I'm an old mechanic.
A cake of soap 🧼 works very well also
Candle wax works better
Nice puller. We shared this video on our homemade tools forum this week 😎
Great idea!! Nice work!
Ah yes, let me head downstairs to my fully equipped wood/metal shop
Well done, I like it.
حل ممتاز 👍ولاكن☝️معقد بعض الشئ..ومع ذالك شكرا لمجهودك 🙋
Great Solution, Design seems specific for particular size. It is dificult to use for various size bearings to pulled out.
Make inner shims of various thicknesses to accommodate different inner race IDs; make the basic tool to pull the smallest bearing you wish to work with and add inner shims to work on the larger ones.
Понравился способ обработки вала. Надо воспользоваться.
i had the same problem on a car gearbox , you can force the bearing out with well soaked bread !! push the bread into the centre of the bearing find a quite good fit bar and hammer it in thus forcing the soaked bread behind the bearing and forcing it out amazing but it works i think there are videos on youtube about it
😲
@@snoyes34231 Yup. I usually use silicone wax, as it's much easier to clean up after. This guy's idea isn't bad (I've done similar, but not for blind bearings). However, you'd have to make one for every size bearing shaft you could come in contact with. I bet it took him the better part of a full day's work to complete this. The bread or silicone trick would've had you done and moving on w/in ~5min.
😊😊
Good "lathe" - angle grinder post. Good idea
That's genius!!!👏👏👏
I shoot grease in the bearing cavity and use a punch or piece of stock ground to fit through I.D.. Hammer punch and hydraulic pressure removes the bearing, works every time. Thank you for posting this, good tool making skills.
Very clever design!
Uma ideia show de bola
Always enough space under the bearing to allow the puller jaws to grip!
Cute!
Yeah convenient.
Anyway you can just use bread. No gap needed under the bearing.
@@wizrom3046 Or heavy grease and a wooden dowel, like I've done in my Shop for years.
@@regsparkes6507 I like silicone wax (easy to clean up), but, yes, simple to do when you employ hydraulic pressure.
Good job👍
Congratulations, great job.
Brilliant!
great tool build its amazing with the tools wich you are using dont get me wrong wich are home made and very well made you accomplished making a very totally funktional tool. i am a machinist and have a lathe and mill and i really dont think i could make that tool any better than you for funktionability.
И под каждый размнр делать снова? -Кусок хлеба поможет изъять подшипник.😂
Very nice
¡Esta herramienta es muy profesional!😉👍👍👍👍
Amazing tool👍
Good job👌👍👏.. Thats a brilliant idea💭...
It’s a wonderful idea! Nice and simple work. Your sliding angle grinder is so good. Have put any video about it? If so please send link
Instead of taking help with heavy tools to make bearing puller.... You can remove bearing in cheaper way.... Just break candle in small pieces and fill in middle hole of bearing and tap with same size of bearing hole bolt which can easily move around in bearing hole tap tap until bearing come out.... But it work when other side of bearing cover with part surface
Great idea but if have larger or smaller bearings might not work same.. a small slide hammer kit with the 2 hook style is what I have from Cornwell tools.. just the lip of the hooks get mangled or bent kinda easy.. iv had to warranty it twice
Very clever!
That's a good one!!!
சிறப்பு 👍 💐
Good work
Simple and i need that puller. I will developmenting for big size . Thank you for your idea. Regards
Shove bread or silicone wax into the bearing's hollow shaft. Take a piece of the appropriate sized shaft steel and pound it into the hole. The bread/silicone will force the bearing out (hydraulic pressure). You're done in under 5min, you didn't have to make a custom tool, and it'll work for almost any sized bearing.
Really great 👍
Amazing❤
🎉🎉🎉 فكره رائعه بأدوات بسيطه اشغل البال بالمحال 4:51
Good video for watch
damn! that's good.
Mantap
Good luck sir 🎉
Amazing mr👍👍 good job 👍👍👍
Very good
Super👌
Красафчик
Good
лайк я зробив з ресори
Nice
Я тоже самое делаю обычным анкером.
Этот съемник только под один фиксированный внутренний диаметр подшипника.
👍👏👏👏
👍👍👍👍👍
next up, Make a crankshaft / DIY diesel crankshaft
Lol, whatever. Get started on making that tool and I'll have the bearing out before you have your stock centered to start turning because i was able to find a stick and some rags and some grease.
What if the bearing is not sealed or there is an oil gallery behind the bearing?
I used bread to remove my pilot bearing in my Nova
👍👍👍👍
Do jednego rozmiaru łożyska.
Co gdy będzie większe?
Hi friend which country are you from
👍
My dad was a machinist by trade, he would have thoroughly enjoyed watching this.
hmmmm. just take short pieces of rods at different diameter. split one end. insert the spit end in the blind hole bearing and jamm at the splitt a wedge. Then pull, or hammer out. I have to admit you did a nice tool that you can use for 1000 projects...
BTW: WD40 also helps.
I hope you wear a good dust mask. Thats alot of metal particle and grinder dust for one project.
Mroźna prościej 😁😁🤣🤣
4 hour to build an only use once in a lifetime, very specific to one size bearing , what if the next one doesn't have clearance for the puller? grease,, a punch and hammer would have had that bearing out before a guy would have finished taking measurements for tool design
Sir/ paano mag order sa iyo nyan? Magkano kaya yung tatlong puller? Salamat po.
Ótimo invento muito útil!!!
de que material es? que acero usaste?
Ķ
Mujhe yaisa tool chahiye
Маладцы
👍☕💪
So you're saying I don't have to pack my pilot bearing full of bread to get it out
Price please sir
0:48 OMG xD just take this rod to a man with a lathe and he will do this for a beer.
Troppo lavoro.meglio comperarlo gia fatto
I dunno, the 2 times I needed a blind hole puller, I went down to Auto Zone and borrowed one for free. Worked great.
But you can buy a complete set for a wide range of bearing sizes for only £27 and they work so much better than this.
ŚCIĄGACZE MAMY GŁĄBIE
इसके बनाने में ज्यादा खर्चा आ जायेगा बहुत लेंदी प्रक्रिया है
KUCH BOLECH NA?
KUCH CHALECH NA,?
MAZI RADHA RUSLI KA?
ISKA मतलब
मैं मुका vdo बिलकूल भी पसंद नाही करता हू,,
Sure, go out and buy thousands of dollars worth of equipment so that you can build a 100 dollar tool.
Smart way to save money.
Innenlager Abzieher versch. Größen gibt's für kleines Geld zu Kaufen.
BASTLER bauen es lieber selbst.
Depende el dinero que cada uno tenga, si puedes apañar materiales gratis, lo veo bien como lo hace
Only for one size😂😂
Asambal karma ph karo
i want beans 1 piece
Inner bearing remover, good decision, bad idea, it will damage bearings.
Perhaps the reason it is being removed is because it’s being replaced.🤷♂️
In which case it would be way easier to just cut the bearing.
Jesus....just buy the friggin' tool.......
not very smart idea ...
or you can just buy one wholeset of different sizes+bearings installer,not practical...😂
Dude, get a lathe and a mill and START working seriously !... these Angle Grinder "Craftmenhip" is just annoying
muy fragil veamos si en rodamiento mas grande y agripado resulta
😂😂😂😂😂 Серьёзно?
А можно ещё сложнее?
А если другой диаметр подшипника тогда что?
Мастер 😂😂😂😂
Mantap
👍👍👍👍👍
👍