.... de tete la fiche que j'avais faite c'est les paramètres pour le display LH-100, la c'est le wxgh-100 d'où sûrement les petites différences.... n'étant pas non plus un expert, et pas la doc du display fourni avec, je ne peux que supposer.
Hello! Unfortunately I can't read French, Unfortunately, I also have a display like this and would like to know which P setting is for what. Would someone with French knowledge please be so kind as to write in the comments what P settings are for what?? Thanks!
Power (On/Off) Mode (Km/voltmeter) 2sec mode (headlight on/off) (Prog mode, Power 10 sec, then Mode without releasing Power. code 6666 then 2 sec Power) (LH-100???) (or power + mode: 2 sec for WXGN100) (Mode to change the value, Power to validate/go to the next one) P1: Screen brightness. P2 (miles) / (km/h 0) P3 battery voltage P4 screen timeout in min (10) P5 assistance level 0 (0/3) - 1 (0/5) (103, 1XX does not go through speed 0, 0XX goes through speed 0, XX3-5-9, number of speed steps) P6 wheel size in inch P7 number of magnet in the wheel (30) P8 clamping (speed limitation in %) 100%, or less depending on the project (stroller at 55%) P9 start by pushing (no) or (direct trigger: 0) P10 trigger or PAS (0 NOT prio) (1 prio trigger) (2 both can work at the same time): parameter for me, 2 P11 PAS sensitivity (pedaling) P12 Pedaling force (???- for bicycle) P13 Number of magnets on the bottom bracket sensor disc (for bicycle) P14 current limitation (0-20A) (impossible to modify) P15 protection voltage (29.0V) (100???) P16 reset km P17 cruise control (0 off - 1 on) P18??? (not on WXGN100) P19??? gear ratio (not on WXGN100) P20 GAS or PAS sensor (not on WXGN100) 99 - 99 (???) d0 - 4 (???) For certain values I do not have any information, since the person from whom I retrieved the information did not have the information.
You're a hero, you know that? Thanks alot! There are 2-3 other versions of this display, some of the points in the instructions are the same, but others are not. The P settings you listed match what I see on my display. Apparently we have a rare version with the "wxgn100" because even Google can hardly find anything about this version. You saved me the adrenaline of having to figure it all out myself and maybe doing something that could have destroyed something. again. thanks thanks thanks! By the way, I installed this controller in a NinebotG30D with a 60 Volt Battery to avoid the German 20 km/h speedlimit :)@@nicolassamson552
You're a hero, you know that? Thanks alot! There are 2-3 other versions of this display, some of the points in the instructions are the same, but others are not. The P settings you listed match what I see on my display. Apparently we have a rare version with the "wxgn100" because even Google can hardly find anything about this version. You saved me the adrenaline of having to figure it all out myself and maybe doing something that could have destroyed something. again. thanks thanks thanks! By the way, I installed this controller in a NinebotG30D with a 60 Volt Battery to avoid the German 20 km/h speedlimit :) @@nicolassamson552
You're a hero, you know that? Thanks a lot! Unfortunately my other comments were deleted from CZcams for some reason. That's why I'm keeping it short now. Thank you very much, you saved me a lot of work and trial and error!@@nicolassamson552
Eres el mejor bro 🌈👋👋👍👍👍👍
Salut comment fait tu pour modifier les ampère p 14 je suis sur 1
Salut, j'ai pas pu modifier ce paramètre, je suis resté d'origine à 1 aussi.
(Je pense qu'ils ont fait une mise à jour et que ça se gère automatiquement, par cq'en roulage il est clair qu'iln'y a pas qu'un ampère ^^)
.... de tete la fiche que j'avais faite c'est les paramètres pour le display LH-100, la c'est le wxgh-100 d'où sûrement les petites différences.... n'étant pas non plus un expert, et pas la doc du display fourni avec, je ne peux que supposer.
Mercj de ta réponse !
Hello! Unfortunately I can't read French,
Unfortunately, I also have a display like this and would like to know which P setting is for what. Would someone with French knowledge please be so kind as to write in the comments what P settings are for what??
Thanks!
Hi, i look when i go back home
Power (On/Off)
Mode (Km/voltmeter)
2sec mode (headlight on/off)
(Prog mode, Power 10 sec, then Mode without releasing Power.
code 6666 then 2 sec Power) (LH-100???)
(or power + mode: 2 sec for WXGN100)
(Mode to change the value, Power to validate/go to the next one)
P1: Screen brightness.
P2 (miles) / (km/h 0)
P3 battery voltage
P4 screen timeout in min (10)
P5 assistance level 0 (0/3) - 1 (0/5) (103, 1XX does not go through speed 0, 0XX goes through speed 0, XX3-5-9, number of speed steps)
P6 wheel size in inch
P7 number of magnet in the wheel (30)
P8 clamping (speed limitation in %) 100%, or less depending on the project (stroller at 55%)
P9 start by pushing (no) or (direct trigger: 0)
P10 trigger or PAS (0 NOT prio) (1 prio trigger) (2 both can work at the same time): parameter for me, 2
P11 PAS sensitivity (pedaling)
P12 Pedaling force (???- for bicycle)
P13 Number of magnets on the bottom bracket sensor disc (for bicycle)
P14 current limitation (0-20A) (impossible to modify)
P15 protection voltage (29.0V) (100???)
P16 reset km
P17 cruise control (0 off - 1 on)
P18??? (not on WXGN100)
P19??? gear ratio (not on WXGN100)
P20 GAS or PAS sensor (not on WXGN100)
99 - 99 (???)
d0 - 4 (???)
For certain values I do not have any information, since the person from whom I retrieved the information did not have the information.
You're a hero, you know that?
Thanks alot!
There are 2-3 other versions of this display, some of the points in the instructions are the same, but others are not.
The P settings you listed match what I see on my display.
Apparently we have a rare version with the "wxgn100" because even Google can hardly find anything about this version.
You saved me the adrenaline of having to figure it all out myself and maybe doing something that could have destroyed something.
again. thanks thanks thanks!
By the way, I installed this controller in a NinebotG30D with a 60 Volt Battery to avoid the German 20 km/h speedlimit :)@@nicolassamson552
You're a hero, you know that?
Thanks alot!
There are 2-3 other versions of this display, some of the points in the instructions are the same, but others are not.
The P settings you listed match what I see on my display.
Apparently we have a rare version with the "wxgn100" because even Google can hardly find anything about this version.
You saved me the adrenaline of having to figure it all out myself and maybe doing something that could have destroyed something.
again. thanks thanks thanks!
By the way, I installed this controller in a NinebotG30D with a 60 Volt Battery to avoid the German 20 km/h speedlimit :)
@@nicolassamson552
You're a hero, you know that?
Thanks a lot!
Unfortunately my other comments were deleted from CZcams for some reason. That's why I'm keeping it short now.
Thank you very much, you saved me a lot of work and trial and error!@@nicolassamson552