Remove/install an excavator motor
Vložit
- čas přidán 3. 08. 2024
- Yanmar B37 excavator engine rebuild project:
0:00 into load on flat bed truck
9:37 Wash and move into shop
14:16 start removing engine
25:00 lift engine out and remove parts off engine
33:05 Bring engine, radiator, starter to rebuild facilities
39:50 start assembling parts
51:25 engine install
1:02:25 attempt to start
1:08:48 Fix frozen blade control
1:14:13 Drive it out of shop and load on trailer
1:22:06 Bring to a site to install culvert pipes and hammer rock
Bid on old engine parts:
www.shopcamarata.com/product-...
Instructions to bid:
1. Register for an account www.shopcamarata.com/my-account/
2. Once logged in, purchase the lab inspector bidder verification product for $1, this payment will be refunded. - Auta a dopravní prostředky
Andrew, you did a good job putting that excavator back together. Two things. When attaching ground straps, don't use the bolt as the current path. The current path is through the flat surface of the lugs and the structure. You want to remove the rust where you land the wires. To take it a step further there is a conductive coating that can be applied first and spray some paint to seal it up. It's called Grounding and Bonding. 2nd don't use Teflon tape on a sensor that has one wire. The sensor gets its ground from the threads. Great job getting it running!
Thanks
Tell cody I said hi
@@AndrewCamarata alot of times you have to use something. I usually just do one wrap in one spot using the thin tyflon thinking it will tear on the outside of the threads and clog up the valleys where it would leak. also the adjoining threads where you did not teflon will supply the ground.
Two things 👏👍
I clean the bolt's shoulder, the threads, the threaded mount surface, the lug on both sides all with some sort of rotating wire wheel. A wire brush normally doesn't cut thru the oxide coatings accumulated over decades.
Then Kopr-Shield everywhere. It'll conduct fine forever if ALL of this is done
Only Andrew can scoop one excavator with a bigger excavator ❗️
Genius ❗️❗️❗️
Every operator can do that.
Next for your castle should be a lift next to your stairs. Big enough to fit a pallet or 2. (Elevator)
Bro, that's a bulldozer. He's lifting a mini-excavator with it.
@@SalandFindles tracked loader. isn't it?
That was cool.
Like she just gave birth to mini exc
Look at all the small businesses Andrew supported to make this happen. I'm more amazed that there are that many local guys available to do that kind of work!
too sir
Yes. I’m glad the guys who specialize in those fields are here.
@@AndrewCamarata Would be great if you ever got a chance to highlight some of these specialize operations. I can't imagine the detailed level of knowledge and experience it takes to efficiently rebuild some of these parts. Sizes, specs, threads, motors, etc. It's like entire generations of engineering knowledge just waiting to evaporate out of our society.
Don’t forget people are buying junk pistons to help his business 😂you know you’ve made it in life when people are buying your trash 🚮 unbelievable
@@MrAllmotorB With 'Certificate of Authenticity' 😂
Watching Andrew changing an excavator motor is like watching Bob Ross paint.
Watching @Ants Pants changing an excavator motor is like watching Salvador Dali paint.
Congrats on being in business for 15 years. I've been watching your videos for just over 7 years since right before you built the Castle. You're an interesting and entertaining guy and I hope you have 15 more in you. Cheers
That LITTLE smile on ya face when the engine started 😝
same. just need more chainsaws again
Cheers! I feel the same way. AC is a force.
All of his success comes from the sweat of his brow, being bold, being ENTREPRENEURIAL, and putting in the time, good bad and ugly.
t em@@timregan1005
Anyone else love how he just put the pistons in the dishwasher😂😂 Only AC LOVE IT!!!!
Also great for stainless steel pistol parts .
Lol oh no no no, that sir is an indoor parts washer. “We don’t need no stinking (badges) dish washer”, Paper plates and plastic spoons n cups
Diesel parts makes the dishwasher a new black color 🤣 But it works 😸
He'd never get away with cleaning the old pistons and other miscellaneous parts in the dishwasher if he were married! 😂
We always use dishwasher for cleaning parts, also plastic, but no rubber!
Where do I start. Another excellent video. Classic Andrew Camarata - informative and enjoyable. If anyone thinks they're facing a project that's too big just watch one of Andrew's videos and get a lesson in how to get it done. No fanfare, just focus and effort.
The smile on Andrew's face when the excavator started for the first time is fantastic. Clearly he earned the opportunity. My only regret is that this video is only an hour and a half long. Felt like only 15 minutes. Thanks, Andrew.
there are 5 minute videos too long to watch, this one flies by before one notices.
So true. Another great video and another project solved.
On those paper Gaskets (like the thermostat one you showed assembling DRY) that kind of stuff works a LOT better with a thin smear of regular grease on both sides of the gasket, it makes the paper soften and swell up a bit and seal better, AND next time you goto remove it it wont be as stuck
You can't truly appreciate the size of the Koehring when it's alone in a rock pit, or with the crusher or haul truck. Seeing it dwarf the Yanmar and lift it up with ease really gives some perspective. 😂
was thinking the same thing
Yeah that sucker is huge
Nice Koexistence
yanking that thing around like it was a dog's chew toy.
Andrew "Let me just lift this whole excavator with a track loader" Camarata
Never a dull moment!
No substitute for brute force .
yep him and bushradical for me. How much? Bought raw land 3 years ago its now amazing. And I just bought a bobcat 331 excavator.
It has tracks and it got loaded. Seems about right to me 😂
The logistical accumin and problem solving ability of Andrew is amazing. I've been around the earthmoving industry for many years but am still amazed at his methods. Great to watch but stand clear.
Moved a lot of dirt with that Yanmar. Glad to see it back in business. Nice to work with folks that can actually rebuild engines, re-core radiators! 💪👍🏼
Everyone thought the $4,000 excavator was small and then you load the b27 in and out of the bed of a truck like it’s an attachment. 😂
The pressure washer alone was $6000
આ પાનાંમાં આચઃઇઃં અંદર😢@@HappyHands.
@@HappyHands. he bought it at auction for less
excellent...you must have helped sell so many Yanmar machines....good fix AC.....and nice to have a camera operator filming you. nice edit.
Prolly froze and evacuated its bowels in the winter. One of the reasons why i have a portable vacuum pump setup. I just vacuum the liquids inside something that's going to stay static for more than a few months and put a rust inhabitant anti-freeze mix in return. Zero chance of busting something. Learnt it the hard way. The 5D sieve way.
40:38 close enough. Coolant loss is what killed it tho.
Seeing you put bolts back so they wouldn't get lost or so you don't become confused to were they go sorta works. Many times you end up removing the bolts again to get the next part off. I have a system. I use large plastic drinking cups labeled with indelible pen. On big jobs I've had a forest of glasses. Watching them disappear one by one as the job is completed is satisfying.
Yeah, that works too, I did that on some things here.
Oh man, I thought I was getting to bed early tonight…. SCREW THAT ! It’s Camarata time boys !!
Hell yeah brother!
Woah... Grab the popcorn ya'll 👍 Nice long 1 from AC 👍
Hey Andrew I am glad you got the old Yanmar Excavator up and running. She is a hard working BEAST.
Thanks for all you do and all you continue to do. Cause you are an inspiration to us all. 😊
My B22 decided to destroy the radiator. That turned into injectors, and an injection pump bleeding into the case. It is great that at least for those 3TN's there are parts. But between you, me and Ants Pants, I think we have used up every part in the US.
Gotta like before you start watching ❤️
Super like!
glaze more
Same lol
Always do!
Mouthpiece
I love watching these with the subwoofer on full. My neighbour shares their renovation noises with me during the day, I share Andrew back in the evening.
💀🤣🤣🤣
Ok boomer.
Because you’ve never done any work at home huh?
@@FlourescentPotato I’d rather be a boomer than be poor and not know my own gender 😂
@@sjv6598 not really, I rent a pretty fancy beachside apartment, there isn’t much that needs doing.
I very rarely ever hit the like button anymore on CZcams, except for Andrew's videos.
Thanks Andrew! I love your attitude of persistent effort and not getting in your own way, like many of us do.
This is proof that the snap on truck may be fun, but is also not necessary. Andrew does all this without the big name tools.
This is a big one for me. Crazy seeing a guy work on stuff with tools I would throw out 😂
35yrs working on everything from lawn mower wagons to large off road equiptment and have broken some of all brands, nothing is superior if what you have is in your budget and works.
@@tipperryan Just love seeing Andrew still using the old Craftsman 19.2 1/4 drive impact.Gord Ontario Canada
Yeah I always notice this because zero CZcams guys do this. We’re always trying to aspire with better tools when in fact we should use what we have. For me a flex is using a plug in tool because my air compressor stinks.
1:21:39 Double Trouble threw me way off. I know I'm sitting here watching this on midnight shift trying to get through the last few hours. Wow, I really thought my eyes crossed... LOL!
38:15 .. Love places like this, I used t take all my alternators and starters to a guy to rebuild, who has a place like this, always did the best work!! :)
A couple of great points Andrew makes in the video
Take photos
& make a list...
Makes life so much easier
The list was helpful because I wrote down everything I did, then when I put it back together, I did it in the reverse order.
That's some good discipline. I have the bad habit of getting right into the project and want to just go go go as I'm enjoying it. Regrets later of course @@AndrewCamarata
@@jasonkirkham3153 Yep, I do the same thing. Sometimes you just dive in, perhaps we should all slow down and take our time. Someday.
@@AndrewCamarataneat trick grandpa taught me to put it on TDC prior to take apart. Saves major time on reassembly as timing & injection pump spot on
Andrew I love the comments you randomly reply to😂 I’m getting my first piece of equipment right now. I’m 23. I’ve been watching since I was in my teens. Thank you. God bless!
A few winters back I taught myself how to do this rebuilding the same engine out of my 955 jd tractor. Great video! I know exactly how that smile feels on the first start up… it’s a real good feeling!!
Hello Andrew, 29'32'', you can weld a washer on your flat key:)
Thank you very much for your amazing videos!
Full of caresses to dogs:)
Bonjour Andrew, 29'32'', tu peux souder une rondelle sur ta clé plate :)
Merci grandement pour tes esxcellentes vidéos !
Plein de caresses aux chiens :)
That Yanmar should last for decades to come. Great job getting it back working again.
What's good about the red antifreeze that Toyota uses is that it's easy to see small leaks when they first start.
Its easy to see the warning light ,too .
+ It could be the original thermostat was the wrong one and the new one in the kit is the right one , the radiator looked like it never had any antifreeze in it .
@@user-ji6qj5xw8t He found a split in a small hose.
You know the drill, always check your fluids and other important functions prior to running your equipment. And if something shows up, stop and analyze the problem before proceeding.
You betcha. Whether it’s a lawn mower , car, any vehicle or equipment that has oil or fluid - check before starting. My step daughter ruined her used Toyota because she never checked fluid. Ran it on almost empty until it seized up.
Seeing a "new" rad, starter, and new hoses makes me smile. Many more hours to go for this Yanmar that has done so many projects for you.
It’s not the the original b50
The genius of AC shines through here. Yes, it's impressive the way he removes the engine and re-installs it after the rebuild, but the real genius is making the project worthwhile in the first place. Under normal circumstances I can't imagine that it's practical to resurrect a little excavator with almost 9k hours and a blown engine, but because Andrew was able to film the process and post it on CZcams the project will pay for itself and then some. Over 300k views after only 1 day.
Can't say I'm surprised at the parts washer but it is typical A/C! Get 'er done, guy!
😂😂 that may have been an outside thing.
Ok Andrew, I’m sure you’ve been asked a million times and I just haven’t looked hard enough to see it (we your fans are prolific commentators), what’s up with the Power Wheels?
Thanks for the upload Andrew!
You're welcome.
@@AndrewCamarata where are all the "Honeys" tho!!!? I mean your "sidekicks"?? AKA Babes???
L
Love that little Yanmar, glad you got her back up and running.
Yes, it’s also inside my new garage too, so that will be much happier out of the weather.
It's always a good day when Andrew is fixing something rather than breaking it. lol
Andrew has convinced me start looking at properties to develop.
When you were tearing down with the dewalt, I thought that craftsman finally gave up the ghost.. but then on assembly it was right there.... going strong like always. I love that you're not a tool snob and get it done. Keep it up and go see your dad today!!!!
Yes!
Lol that craftsman has been around so long. Can't believe it still works.
I love how he smokes the pics out of every bolt and never straps anything. Dude was born for this.
The certificates are pretty wild, with the seals and all ! Also I love that double edit of you raising the ramps. It’s been a while since you did one
Glad to see you got an induction heater, they’re not for every application but they can be a big help in the right instances. Great job on the repair video I always enjoy watching you diagnose and fix broken equipment.
Andrew: i think i ruined the motor.
Me: You? Nah...you are so gentle with all your equipment. The proof is your pick up truck. 😉
😅
Well it probably wasnt Andrew who ruined the motor, more the lack of ANY coolant. XD I mean, what in the world? How can there be not a SINGLE drop of coolant in there? Where did it all go? Even with a broken line there should be at least a tiny bit of coolant left...
Like the "new" yellow pick up truck he brought to the Castle. 10 min later in the video it's all beaten up to wrecks ...
Andrew, every time you start one of your older pieces of equipment, and it takes a while for the engine to build compression, I just want to rebuild them all.
Best part of all AC"s old equipment is NO Computers! DIY
These machines/toys excites the little boy in all of us.
I agree, in the “60’s” when I was a teenager I operated some of the heavy equipment he has . Drove dump trucks, etc. it was big boy toys then as it is now. Totally enjoy his videos for years now.
Andrew, get yourself a milwaukee 12v impact. They are strong enough to pull even lugs but small enough to use all day long and get into super tight spaces.
Yea brake all the bolts too he used that small so nothing would snap
I heard Milwaukee cordless impacts are really good!
If Milwaukee or the Chinese company that owns it wants to be a sponsor I’m sure he would consider it.
This is how all mechanic videos should be done not all jump cuts and talking about what you did
There is something really special about that Yanmar excavator.
There;s never even the slightest urge to fast-forward, I want to take in every frame of these videos. And there is much pausing and re-playing of stuff.
Awesome! Just when I thought there was nothing on tonight.
Thanks Andrew!
agree yes
I love how Torque Specs don’t exist and have no place in his garage …. awesome swap out!!!
Sounds like that poor craftsman impact driver needs a bearing. Thanks for the great video! These fix videos are my favourite. If you fix your drill please make a video of it!
Can't wait for castle number two to get started andrew.
Exciting is a understatement!!!!
Wow, I'm not going to hear a single thing my wife says for the next hour and a half. 😂
Its 3.03 am in the UK . I couldn’t sleep NOW I can’t sleep !!
😅😅
Yeah, honey don't disturb me Andrew's got a new video on now
Same😂😂😂
Lmfbo!
1:03:43 Andrew's face of elation when the beast comes to life is priceless
Cool video! I like that you are adopting some Applied OCD techniques as you work, like putting bolts back in their holes and taking lots of pictures!
Nice to see Dave helping out in the shop. Andrew sure deserves a hand.
Nice job. I was surprised you didn't use anti-seize on bolts going back together.
Caught the run a tap to
clean threads on captive nut. What? No anti seize?
Murphy Switch - add to prevent idiot from just restarting & killing it.
Andrew understands " It's not just a tool, it's a money maker"
Obrigado! Quebrei meu pé e tenho sofrido com fortes dores... aguardando cirurgia... agradeço o entretenimento! Fiquei distraído pelo vídeo e esqueci de mim por muitos minutos... obrigado!
I'm so envious of your gantry chain hoist. You nsiled it with that. Great planing. It's been a real joy watching for over 12 yrs - have learned so much, given me inspiration & great ideas for my property. Thank you for all your hard work on video production, your the best. "Get back to work, no overtime!"😂😅
I appreciate that you keep things so clean and organized. From the first video I've ever watched and every video following you've done this and it's great.
3:50 AWWWW what a cute scenery. A mother tracked loader is carrying her baby excavator.
Hey Andrew, Give us a video on your night time yard lighting on the new storage building, Castle and landscaping. I bet it looks nice. I'm building a Japanese style Wabi~Sabi Garden. A long process.
Anoche fue la mejor inversión de 1h 35' 46" de mi Tiempo. Eres una persona totalmente interesante (te veo desde hace muchos años) por como resuelves y actúas en temas que quizá no sean de tu especialidad u ocupación habitual. Logras entretener y mostrar (enseñar) como se "encara" la Vida y sus obstáculos. Te agradezco que filmes, edites y publiques todo tu muy valorado material.
Saludos y felicitaciones por tu arduo trabajo desde Chubut, Argentina de parte de un Técnico Mecánico automotriz y de Aviación (ya retirado) y con mucho Tiempo, que no es igual a mucho resto de Vida.
The overhead crane in the shop is such a luxury also the great shop lighting for the footage, thanks.
Love those mountains!
Great view.
yup
Andrew a mi me gustaría poder tener un recuerdo tuyo pero te sigo desde Zaragoza , España y también tengo 75 años bueno me conformó con ver tus excelentes vídeos gracias por todo un abrazo desde Zaragoza
When you prefer a machine, it's worth the hassle to get it restored. This one can easily go another 30 years. There's no escaping the maintenance anyway, even with a new machine. Just moving the broken excavator was a project in itself. Excellent video.
Putting the excavator into the truck is classic Andrew Camaratta. Fantastic! 😊
Thats the narrowest alternator I've seen . Andrew it's good habit to check fluids before using any equipment 👍
It's like he jacked up the body and put a new excavator under it. The world's not ready for two Andrews so i'm glad that was camera trickery.
This machine is the reason I bought my yanmar 50! Thanks for keeping her alive.
You should send one of those scored up pistons to the operator that kept running that machine after it was overheated as a memento. Glad you rebuilt that little Yanmar I always liked that little excavator. You know the work pool is getting pretty lean when you only trust yourself to let the ramps down on the trailer. Great video as usual AC keep them coming!
It may not have been all the operators fault if you remember it was sending false information about being hot and oil pressure Los anyway I watch the whole thing from start to finish this morning
Definitely not the owners fault.Oh wait, I thought he was the guy who is supposed to take care of the machines maintenance.😮
I bet that’s the first time a mini ex was in the bed of a deuce ever.
I have to tell you Thank you for your show's your, constant work at maintaining with checking the oil and water and lubeing and cleaning up the machines has motivated me to be more attentive to my equipment and just as you are working on your excavator I have been cleaning and changing the oil in my mini that I have been using to remove trees on our farm in preparation for building a new house and two new shops for my retirement projects
Wow that overhead hoist might be one of the most valuable things in the shop. Going to have to go on my list of must haves.
A radiator shop can take it apart and run rods through the slots and open them up. If a new one is outrageously expensive
love it. Not a torque wrench in sight. Very relatable! Just the way I do it!
Until he needs to undo the bolts he over-tightened.
@@kenadams5504 thats what the induction heater is for
I love Yanmar mini excavator got a 1994 No break down only tracks and a few hoses .
Amazing quality.
Ps they use british std pipe on hydraulic fittings.
Andrew, not being mechanically inclined myself, I truly enjoy your abilities and fearlessness when taking on big jobs.
Hope you record some lake adventures again this summer. Good to see you have a recreational break occasionally.
Wait, did Andrew just put engine parts in the dishwasher? Lol I love it!! 🤔😂🤣😂🤣
No but sometimes he puts dishes in his parts washer
Lol I've never seen an excavator in a bucket haha. It looked like a baby in that thing. So many toys!
This video shows how very important it is to do regular consistent maintenance on your equipment!!! Neglect can cost you a ton of money!!!!
You sure put a lot of great work replacing motor and radiator. I suppose operators must put more care into operating older machines.
10k views in 30 minutes ❗️❗️❗️
Good movie must be on ❗️❗️❗️
Get your popcorn ready and enjoy this great production ❗️❗️❗️
Not sure why he would reuse the old radiator hoses after going this deep into the engine and rebuilding the radiator, but there is usually no doubting anything AC does, so maybe they were recently replaced. Another great video.
You can tell that little Yanmar excavator occupies a special place in your heart the grin when you fired it up again was good to see.
never a dull moment when Andrew needs to fix something
not even 5 min in and we've already got some camarata ingenuity love your vids man
1:03:46 Look man can be happy over small things..even sound of the engine..thats pure smile.
Glad to see the Yanmar is fixed! I know it has been awhile since we have seen it in action but it really does seem to have more get up and go and power it seems!
Nice work Andrew! Thanks for sharing with us!
The timing gears were out of synchro or the paint marks were incorrect ?
Your repair videos are my favorite. I like seeing your work. I am a mechanic by trade. With the work you are doing I think you would benefit from a good set of pro level wrenches. Ratcheting versions also. The crap wrenches you are using are a curse. Maybe I’m just a snob but I have my good stuff at work and when I’m working at home with my “extra” stuff if really sucks.
Another great video. I like how he takes responsibility. (I blew the motor) Not many CZcamsrs will do that.